golmar ART 7AW/G+ User guide

ART 7AW/G+
ART 7AW/G+ V01 REV.0121|ENGLISH
INSTALLER
MANUAL

CATEGORY 1_HEADERCATEGORY 2_HEADER
2Footer Infos
IP G+ ART 7AW/G+
2
www.golmar.es
INDEX
1. Safety cautions and warnings...................................................................................................................................... 3
2. Characteristics .............................................................................................................................................................. 3
3. Device description........................................................................................................................................................ 3
3.1. Jumper description.............................................................................................................................................. 4
4. Device installation........................................................................................................................................................ 4
5. Monitor conguration ................................................................................................................................................. 5
6.Web client....................................................................................................................................................................... 5
6.1. Settings.................................................................................................................................................................. 6
6.2. SIP Servers............................................................................................................................................................ 6
6.3. About..................................................................................................................................................................... 7
7. Settings........................................................................................................................................................................... 7
7.1. Address.................................................................................................................................................................. 8
7.2. Privacy................................................................................................................................................................... 8
7.3. Guard..................................................................................................................................................................... 8
7.4. Devices.................................................................................................................................................................. 9
7.5. SIP.......................................................................................................................................................................... 9
7.6. Password ............................................................................................................................................................... 9

3
ART 7AW/G+ IP G+
www.golmar.es
20-09-2017 Wed
Intercom Events App Settings
09:27
View
Status leds
Speaker
- TCP/IP video intercom system.
- Installation in an existing network structure (requires the addition of D4L-G+/PoE switches) or in its own structure using bre or
UTP cable of category 5 or higher.
- Up to 98 blocks for each installation.
- Up to 19 door panels for each block.
- Up to 799 apartments for each block.
- Up to 19 general gurad units for installation and 9 gurad units for each blockl.
- Up to 32 IP cameras with ONVIF protocol,
2. CHARACTERISTICS
- e installation and handling of this equipment must be carried out by authorised personnel only..
- e current regulations require the feeder to be protected with a circuit breaker.
- e entire installation must travel at least 40 cm from any other installation.
- In the power supply (FA-G+):
- Do not over-tighten the screws of the terminal strip.
- Install the power supply in a dry and protected place, without risk of dripping or splashing water.
- Avoid locations near heat sources, damp or dusty.
- Do not block the ventilation slots so that air can circulate freely.
- To avoid damage, the power supply must be rmly anchored. Usea a DIN 46277 guide for xing (8 DIN).
- To avoid electric shock, do not remove the cover or handle the wires connected to the terminals.
1. SAFETY CAUTIONS AND WARNINGS
3. DEVICE DESCRIPTION
- Front side
DUAL
POE
MONITOR IP 7”
ART 7AW/G+
12310720
GOLMAR S.A.
C/ Silici, 13
08940 - SPAIN
DUAL
POE
48V
18V
12V
GND
PCM IN
HZ+
HZ-
RJ45
PCM OUT
FPOE
SPOE
AL5
AL6
AL7
AL8
GND
GND
COM1
NO1
COM2
NO2
AL1
AL2
AL3 AL4
SA
GND
12V OUT
GND
485+
485-
- Back side
Microphone
RJ45 connector.
Alarm input connectors.
HZ(**)
(*) Makes reference to the doorbell of the house.
12V local power connector..
PCM/G+ connector
Power mode selector
jumper.

4
ART 7AW/G+IP G+
www.golmar.es
4. DEVICE INSTALLATION
1- Avoid exposing the monitor to backlighting from light
sources for optimal picture quality.
1,65m máx
1,45m máx
1,85m máx
16-03-2020 Mon
View Intercom Events Settings
11:24
2- Place the top of the monitor at a height of 1,65 m
for a correct viewing of the screen.
1,65m máx
16-03-2020 Mon
View Intercom Events Settings
11:24
Monitor location.
Necessary elements to complete an installation:
• FA-G+ power supply for each 8 devices (door panels, monitors...).
• Make the distribution of the dierent devices through 4 distributed outputs D4L-G+/PoE distributors or via standard PoE
switches.
• Choose 6502/G+ door panels, or a modular composition for the Nexa panel to be able to register all the units in it and set a
video intercom system as such.
In case of daisy-chain distribution of the devices (IN/OUT), use DCP/G+ injectors, accompanied by a FA-DC48/G+ power supply
and DCS/G+ ethernet switches in the monitors.
Use the monitor stand so that the monitor is at the above
mentioned height.
Place it in a at surface which allows a good t of the stand to
the wall.
3.1. Jumper description
FPOE
SPOE
FPOE
SPOE
We will be able to choose what supply voltage will be necessary for the correct operation of the device through the jumper located in the back side
of the monitor as follows:
48 V standard PoE (default position).
e device is ready to receive 48V from a PoE standard switch.
18 V.
e device is ready to receive 18V from a D4L-G+/PoE or from a
DCS/G+ ethernet switch.

5
ART 7AW/G+ IP G+
www.golmar.es
IP address of the monitor.
Subnet mask odf the monitor.
System gateway address. IP address of the system
router through which go out to internet.
If you want to assign a dierent network parameters as the ones that the system automatically assigns, we must to press on the icon located
in the bottom of the screen. is will bring us to a screen where we will be requested to enter the desired network parameters.
Ajustes de red ~ Network settings
Local IP
Subnet Mask
Gateway
Server IP
Automatic
10.0.0.107
255.0.0.0
10.0.0.1
10.0.14.9 Server system IP address. It is the management panel
IP address.
6. WEB CLIENT
We can access the Web Client of the monitor to make changes in the conguration or to congure its network parameters
manually, entering the device IP address in our web browser. If the device still being with its default factory settings, we have to enter
the 10.0.0254 IP address in our web browser. If the device is already congurated, we have to enter the IP address that the system
automatically assigned or we manually assigned.
Type the IP in the web browser:
GO
10.0.14.9
Search
GO
10.0.14.9
Search
e password to access is 888999.
Log in the Web Client:
5. MONITOR CONFIGURATION
Once the monitor is connected to the network, it will automaticalle start and it will show an initial conguration screen in which we must set the
following parameters related with the physical location of the monitor in the installation:
Edificio ~ Block
Dígitos llamada ~ Call digits
Idioma ~ Language
Vivienda ~ Apartment
Monitor
Configuración inicial ~ Initial config
1
5
1
1 / 6
English
Always has to be 5.
Up to a maximum of 6 apartment
unit for each apartment..
Block in which the apartment is
located.
Apartment number in the block..
Save the conguration set.
Manual assignment of network parameters.

6
ART 7AW/G+IP G+
www.golmar.es
Below, it is described the initial screen of the Web Client for the ART 7AW/G+ monitor:
If we do not remember the IP address that we assigned the monitor, we can make a search of IP addresses in the network via searching
programmes as “IP search Tool”.
SIP server
About
Settings
APARTMENT UNIT
Monitor unit
Apartment address
Block number
1
1
1
Apply
Network
Automatic settings
Local IP
Gateway
Server IP
Subnet Mask
10.0.0.107
10.0.0.1
10.0.14.9
255.0.0.0
Dialing code length 5
Language * 1
* Languages
1 Spanish
2 English
3 Portuguese
Next
About the device.
SIP settings.
Settings.
Monitor language.
Dialling code
length.
Block number.
Apartment number.
Unit number of the
apartment.
Available languages.
Manual assignment of
network parameters.
6.1. Settings
Go to the next screen.
SIP server
About
Settings
Previous
APARTMENT UNIT
Background picture
Load Restore
Next
Go to the next screen.
Go to the previous
screeen.

7
ART 7AW/G+ IP G+
www.golmar.es
6.2. SIP Servers
In the SIP Servers section, we will be able to add the device in the PABX switchboard registered in the master panel to make and re-
ceive calls from SIP devices included in the system via extensions assigned to the monitor.
SIP server
About
Settings
SERVER REGISTRATION
User
Password
SERVER LIST
1
2
3
4
5
6
7
8
9
10
Qualvision
Golmar
Office 1
Update
Admin
Register
Registered on Office 1
User and password
created in the PABX
switchboard.
We can change the background picture of the monitor for the picture that we consider through the “Load” option that allows us to
upload an image from our laptop. We also can re-set the default background pressing over the “Restore” option.
SIP server
About
Settings
Previous
APARTMENT UNIT
Applications
Add Delete
1
2
3
4
5
6
7
8
9
YnO
G2Call+
Go to the previous
screen..
We can see which applications are installed in the monitor and install new desired applications. For this, we have to previously obtain
the apk le of the application to be installed and upload it to the list of applications throgh the “Add” option. A progress bar will appear
indicating that the application is installing and when it ends, the application will appear in the list. Otherwise, if we want to delete an
application of the monitor we must select it and then press over the “delete” option. We must press accept in a conrmation screen that
will appear and the application will disappear of the list.

8
ART 7AW/G+IP G+
www.golmar.es
7. SETTINGS
In this section of the manual, we will see in detail the system settings. If you want to see other type of settings to which we can access with
the monitor, see the ART 7AW/G+ user manual that you will nd in the “Downloads” tab in the product website.
When pressing over the system settings, in the monitor will appear a screen in which you must type the installer password to be able to
access the setting system menu. e default installer password is: 2718.
Once you have access the system settings, the following screen will appear:
System
PrivacyAddress
Password
****
SIP
SP
Devices
Guard
To re-set the monitor settings to a factory values, we must press over the icon located in the bottom right on the screen. e
following screen will appear and we must conrm the factory reset of the monitor settings.
Reset all settings ?
Reset
6.3. About
SIP server
About
LOCAL INFORMATION UNIT VERSION
PASSWORD
Local IP
Hardware
Administrator
Gateway
Firmware
Unit
MCU
Subnet Mask
Server IP
MAC address
10.0.0.107
C
10.0.0.1
1.00
1.00
255.0.0.0
10.0.14.9
e6:ff:6f:78:6a:27
Dialing code length
Block number
Apartment address
Monitor unit
5
1
1
1
Reboot Update
888999
0000
Apply
Settings
Restore
Return to factory values.Reboot device. Update FW version..

9
ART 7AW/G+ IP G+
www.golmar.es
7.1. Address
Address
Block number
Dialing code length
1
5
Apartment address 1
Monitor unit 1 / 6
In this section we can modify the system address. If we modify the physical address of the monitor, the network parameters of the moni-
tor will also change. ese can be assigned automatically by the system or manually accessing to the screen explained before pressing
over the icon.
We would ll in the elds in the same way as in the beginning of the conguration but updating the data which have changed.
7.2. Privacy
Automatic erasing
Automatic snapshot
Preview video sources
Privacy
In the privacy section, we will be able to enable or disable the monitor’s view of the door panels and the CCTV IP cameras added in the
system, the automatic snapshot when there is a call from the door panel and the automatic erasing of them aer the set period of 30 days.
7.3. Guard
Guard
Block number
Direct call button
Notify alarm alerts
99
Unit address 919
With regard to the guard unit settings, we will be able to set to which address we will call when we press the direct call to the guard
button from the main screen of the monitor. We will also be able to enable the general guard’s reception of the alarms when them occurs.

CATEGORY 1_HEADERCATEGORY 2_HEADER
10Footer Infos
7.5. SIP
SIP
Server
User
Password
SP
SIP protocol
In the “SIP” section we will be able to add the monitor in a PABX switchboard in order to receive and make calls through the PABX via
a previously created extension for our device in the switchboard. For this, we will must ll in the elds requested by the monitor in the
following way:
Server name which we are going to
use..
Extension created for our device.
Password set in the web client of
the PABX when we created the
extension..
7.6. Password
To conclude with the system settings menu, we will emphasise in the “Password” section which will allow us to change the password to
be entered to access the system setings menu.
Password
****
Enter new password
****
1
4
2
5
3
6
789
0
7.4. Devices
Devices
Floor number
Lift control
Private call module
Staircase light control
Link to access control
01
In the “Devices” section, we will be able to enable, if we have it, the PCM/G+ private call module panel. We will also be able to enable
the li control from the main screen of the monitor and link it with the access control so that, when you open the door presenting the
keys to the RFID reader of the door panel, the li is activated in the respective oors of the panel and the apartment.
www.golmar.es
IP G+ ART 7AW/G+
10

Sist
emas de comunicación S.A.
C/ Silici 13. Poligon Industrial Famadas
08940 – Cornellà del llobregat – Spain
[e-mail]
Telf: [phone]
www.golmar.es