GoPowerBike Plug Runner S901 User manual

RUNNER
ELECTRIC SCOOTER INSTRUCTIONS MANUAL

TABLE OF CONTENTS

Unfolding Your Runner Scooter
1. First push up the latch, releasing the safety
bar.
2. Then, unfold the stem of the scooter until the
safety bar clips into place. Give the stem an
extra push to ensure the safety bar is locked
into place.
3. Finally, unscrew the handlebar folders, open
them up and screw them back into place.
Also ensure the latch on the stem is
tightened after adjusting it to the correct
height.
4. Bear in mind that the scooter is still new and
the joints can be a bit stiff. If you’re
struggling, please do not force ant pieces.
Use bicycle grease or a similar solution, to
help loosen screws or any tight hinges.
Getting Started Guide
2

3
Folding Your Runner Scooter
1. Always ensure that your scooter is turned off
before folding. Turning off before folding
ensures your scooter will not accelerate
when being folded or stored.
2. Unlatch the stem and slide it down until the
handlebar reaches the folding latch, then
tighten the latch. Unscrew the handlebar
folders to fold the handlebar.
3. Release the folding latch by pushing forward
slightly on the handlebars and pushing the
latch down with your foot simultaneously,
and slowly lower the stem towards the base
of the scooter, until the safety bar clicks into
place.

Power On and Off
To turn on the scooter, press the power button, shown above, for 3 seconds,
and the LED screen will turn on. To turn the scooter off, press the power
button again for 3 seconds.
Your scooter will automatically turn off if left idle for 90 seconds.
Speed Control
When your scooter is switched on, you will find 3 speed gears (1, 2, 3) that can
be changed by pressing the “Mode” (“M”) button.
Grade 1: 25KM/H (15 MPH)
Grade 2: 35KM/H (22 MPH)
Grade 3: 40+KM/H (25+ MPH) 4

Lights
To turn the scooter lights on or off, press and hold the “M” button for 3
seconds
Power Indication
The LED display shows the approximate charge level of your battery. For a
more detailed amount of charge remaining, refer to the voltage meter.
For proper preservation of your battery health, we do not recommend
regularly draining the battery below a 20% charge.
Mileage
When your scooter is powered on, the odometer will show the total distance
travelled. To switch between total distance travelled and trip distance, simply
click the power button once.
5

6
Battery Overview
Your scooter is powered by a lithium ion battery, a high-quality battery for
ultimate performance. In order to get the most out of your battery, charge is
fully before the first use.
Features of Your Lithium Battery
Balanced Charging Protection
Each battery is equipped with automatic balancing internal cell voltage protection,
protecting your battery and the voltage current being used at all times.
Overcharging Protection
The battery is equipped with an automatic disabling feature where the battery will stop
charging when it reaches 100%, even if the charger remains inside the scooter.
Temperature Protection
It is very important to keep your battery stored or charging in temperatures of 15-30°C to
ensure it remains safe.
Over-Current Protection
Only chargers with up to a certain voltage can be used to charge this scooter. Anything too
high will not charge the battery, protecting the life-cycle of the battery.
Over-Discharging Protection
When discharging your battery, the output power will automatically stop if the voltage falls
too low to protect the health of the battery.
Short-Circuit Protection
If a short circuit occurs, the battery will automatically stop output to protect itself

7
Charging
1. Plug the charger into an AC power outlet first, then connect the other end
to your scooter’s charging port.
2. As a safety recommendation, do not leave the scooter charging for more
than 10 hours.
3. Ensure the room’s temperature is between 15-30°C for ultimate battery
protection.
4. Charge time: approx. 6 hours
Battery Capacity
48V, 13.2aH

8
Learning to Ride
1. Use the necessary protective equipment while riding your scooter. Please
note helmets are mandatory in some Canadian provinces. Always check
local laws prior to riding your scooter.
2. It is strongly recommended to avoid riding on wet surfaces, unpaved
roads, ice, or snow, as this may result in injury.
3. The use of any electric scooter, or other Plug product, under the influence
of alcohol, drugs, or other judgment-impairing substances is strictly
prohibited and is illegal in select provinces.
4. Respect all local laws with your electric scooter (such as stopping at red
lights, respecting cars, and driving within the speed limit).
5. Sidewalks are strictly forbidden to ride on at all times
IMPORTANT
Please ensure you read and are aware of the local laws and regulation before
riding your scooter. Plug is not responsible for any misuse, negligence or fines
resulting in your use of your scooter.

9
Plug is not liable for any negligence, personal injury, or damage to property or
individuals due to improper use of this electric scooter. All riders will be
personally liable and take full responsibility of their actions during the use of
their scooter. By purchasing this scooter, you agree with all of Plug’s terms and
conditions.
Please ensure you read and are aware of your local laws and regulations
before riding your scooter.

10
Cleaning
To clean stains on the surface of your scooter, use a soft cloth with water to
remove the stain. Other solutions may be used such as toothpaste and
stain solutions, but please ensure that there are safe and do not cause
material decay.
Note: Do not use alcohol, gasoline, kerosene, or any other corrosive
chemical solutions to clean your scooter, as they can damage the frame
and/or internal parts of your scooter. Ensure your scooter is powered off
to prevent any electric shocks during the cleaning process.
When storing, ensure your scooter is in an environment with a temperature
rating from 15-30°C to keep the battery healthy. To improve longevity of
the battery, ensure it is charged to 75% or more prior to storing it for
extended periods of time. Turn the scooter on about once a month to
ensure the charge level has not dropped. If it drops below 30%, charge the
battery back up to 75% before continuing to store it, for ultimate battery
safety.
Daily Protection and Maintenance

11
Battery Tips
1. Opening the battery cover and/or playing with any of the connectors leads
to automatic cancellation of the warranty provided to you by Plug.
2. Do not touch, dismantle, or puncture the battery as this can cause serious
health hazards and can lead to injury. Plug is not liable for any damage or
harm caused by improper actions with the battery.
3. Do not use any unauthorized battery chargers. Adhere to charging with the
provide charger or another charger unpurchased from Plug to ensure no
risk of damage.
4. We truly care about the environment and ask that, in case of disposal of a
battery, that you do so with caution and care for the environment. Please
recycle or ask Plug for resources near you that can properly recycle
batteries.
5. Keep the battery charged to at least 75% and at room temperature as
often as possible for the optimal safety conditions for the battery. Failing
to do so can lead to battery failure and danger (high temperatures can
lead to fire hazards).
6. When storing your scooter for periods longer than a week, ensure the
battery is at least 75% charged and the room’s temperature ranges from
15-30°C. Plug is not responsible for scooter damage that results from
improper storage.

12
Summary
For after-sales and warranty service, contact us at [e-mail]
or call us at 917-900-1110.
- Plug scooters covers all spare parts at cost under the warranty agreement,
and will always be at your service to help you resolve all issues.
- The warranty period is 12 months (1 year) from date of purchase. Plug will
bear the full cost of repairs needed due to manufacturing defects in the
first 12 months.
- All wear and tear of scooters (tires, scratches, damages caused by the
rider) are not covered by the warranty.
- Warranty cases are up to Plug's discretion.
- Warranty does not cover water damage to scooter batteries.
- Any production defects need to be communicated within 14 days of
receipt of the scooter.
Manufacturing Defects
- Any items that are damaged or malfunctioning due to production issues of
the scooter are covered under warranty.
- Production issues, or manufacturing defects, need to have physical proof
sent to [email protected]om.
- Batteries that malfunction due to water damage are not covered under
warranty.
- Examples of manufacturer defects: motor malfunctioning, broken
bearings, bent disk brakes during delivery, etc.

13
Wear & Tear
- All spare parts will be offered at cost under normal wear and tear of the
use of Plug’s electric scooters.
- Labor and maintenance are offered for free under the warranty period for
wear and tear.
- Examples: Used tires need replacing, brake pads worn out, etc.
Upgrades
- Upgrade parts are not offered at cost and are not covered under warranty.
- Labor and installation is offered at cost during the warranty period.

14
Important Notes for Warranty
Failure or damage caused by the following will not be covered by the
warranty:
1. Failure to comply with and follow the user manual’s instructions.
2. Damage caused due to misuse, accidents, or collisions.
3. Damage caused by riding on abnormal roads, paths, or unfit terrain.
4. Storing incorrectly, or charging breaches not mentioned in the manual.
5. Negligence, misuse, or any use not deemed, “responsible riding”.

15
After-Sales Service
For any problem listed in the following table, Plug will provide after-sales
service within the scope of the warranty:
Please note that the acceptance of all warranty cases is up to Plug’s
discretion. By purchasing a Plug product, you agree to Plug’s terms and
conditions.