Graco HVLP TurboForce II 7.0 Manual

PRODUCT FLUID SET #2
17P485
FLUID SET #3
17P486
FLUID SET #4
17P487
FLUID SET #5
17P488
FLUID SET #6
17P489
FLUID SET #7
17P490
Dye
Ink
Non-Wiping Stain
Automotive Finish
Lacquer
Stain
Enamel
Epoxy
Urethane
Varnish
Primer
Industrial Finishes
Latex
Multi-Spec
Butyrate
Nitrate Dope
Solvent-Based Wall Paint
www.graco.com
HVLP TurboForce™II
7.0 / 9.0 / 9.5
Quick Operator’s Guide
Turn power switch to OFF position.
Fill FlexLiner™ with material to
‘MAX FILL’ line. Clean threads and
sealing surfaces if needed.
ROTATE air cap to
desired spray pattern.
HVLP EDGE™ II PLUS.
AutoStart setting automatically turns off
when not actively spraying. Sprayer will start
upon re-triggering of HVLP Edge II Plus gun.
Turn switch to ON position if AutoStart is not
desired.
Verify trigger slide is in SPRAY
position (A), not NEEDLE REMOVAL
position (B).
pattern by rotating air
cap retaining ring.
Disconnect spray gun
from air hose.
Connect FlexLiner™ System
to gun.
Screw cover and ring onto cup.
Tighten ring securely.
Disconnect
gun from
FlexLiner™
System.
Connect air hose to gun.
Unscrew ring
from cup.
Remove lid
and ring from
cup. Verify
FlexLiner™ is
in cup.
Verify trigger slide is
in SPRAY position.
Sprayer is now ready to use.
AB
STANDARD PROCONTRACTOR
PROCONTRACTOR ONLY
SETUP
CHOOSE THE RIGHT NOZZLE
OPERATION
This procedure is for water-based paints and flushing agents. For solvent-based paints and flushing agents (i.e. mineral spirits), you must first
read the section on Fire and Explosion Hazards in the Operating Instructions. Please note this Quick Guide is at no means replacing the official
Graco manual. Graco can at no means be liable for any consequences of not following the safety regulations as stipulated in the official manual.
* Please check the Graco operations manual supplied with the unit for more details.
WARNING

Plug turbine power cord
into grounded outlet.
Disconnect gun from
FlexLiner™ System.
Point gun towards a free area. Evacuate air
from FlexLiner™ System by holding gun
vertically and pulling trigger until
continuous spray pattern is achieved.
Connect gun to air hose.
Turn power switch to ON position.
Point gun towards free area.
Pull trigger and flush gun.
If necessary refill cup.
Repeat process till liquid runs clear.
Remove air plug housing.
INsert Artisan air valve.
HVLP EDGE™ II gun only.
Turn power switch to:
START > STANDARD VERSION
AUTOSTART > PROCONTRACTOR VERSION
Turn TURBO CONTROL
to maximum.
UNscrew ring and lid from cup.
Aim center of spray gun at bottom
edge of previous stroke, overlapping
half of each stroke. To optimise
atomisation, adjust air control knob.
To optimise product flow,
adjust fluid control.
If atomisation is too coarse, use
finer fluid set or dilute
the product with
recommended agent.
Remove retaining ring and air cap.
Clean all parts well with cleaning agent.
Re-insert gun after cleaning.
Set air control.
Clean all parts well, using
a new FlexLiner™ if
possible.
Wipe hose gun and cup
with rag soaked in water or
mineral spirits. Turn off turbine.
Rotate pattern size
control clockwise to
maximum fan diameter.
Fill FlexLiner™ in cup with cleaning agent,
cover cup valve and shake well.
Repeat until parts are clean.
Turn off turbine.
Disconnect
FlexLiner™ from
gun to refill cup
Fill cup with cleaning
agent and connect
FlexLiner™ sytem to gun.
1
2
2a
3
4
5
F
L
U
I
D
L
U
I
THICK
UNEVEN FINISH EVEN FINISH
THIN
EVEN
UNEVEN FINISH
EVEN FINISH
THICKTHIN THIN
PROCONTRACTOR ONLY
STANDARD
PROCONTRACTOR
STANDARD PROCONTRACTOR STANDARD
PROCONTRACTOR
Set fluid control
dial to #5.
STANDARD PROCONTRACTOR
GRACO DISTRIBUTION BVBA Industrieterrein Oude Bunders
Slakweidestraat 31 • B-3630 Maasmechelen
Tel: [phone] • Fax: [phone]
www.graco.com
© 2018 GRACO Distribution BVBA · Form No. 328034ENEU (revB)· 08/18 · Digital version only.
Graco is certified ISO 9001.
All information, illustrations, and specifications in this document are based on the latest product information available at the time of publication.
The right is reserved to make changes at any time without notice. For more information on Graco’s intellectual property, see www.graco.com/patent or www.graco.com/trademarks.
SPRAYING
CLEANING
OPTIONAL ARTISAN AIR VALVE