Graco TurfLiner 826059 Instruction Manual

Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2004, Graco Inc. is registered to I.S. EN ISO 9001
310928A
Operation
TurfLiner™
- Use with Water-Based Materials -
Model 826059
900 psi (6.2 MPa, 62 bar) Maximum Working Pressure
Patent pending
Read all warnings and instructions
309045
309053
WLD

Warning
2310928A
Warning
The following are general warnings related to the setup, use, maintenance and repair of this equipment. Additional,
more specific, warnings may be found throughout the text of this manual, where applicable.
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as gasoline, solvent and paint fumes, in work area can ignite or explode. To
help prevent fire and explosion:
• Use water-based materials when spraying and cleaning.
• Use equipment only in well ventilated area.
• Do not fill fuel tank while engine is running or hot; shut off engine and let it cool. Fuel is flammable
and can ignite or explode if spilled on hot surface.
• Do not fill fuel tank with sprayer sitting on any vehicle where static electricity may occur.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop
cloths (potential static arc).
• Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just
a cut, but it is a serious injury that can result in amputation. Get immediate medical attention.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the spray tip.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Do not spray without tip guard and trigger guard installed.
• Engage trigger lock when not spraying.
• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking, or servicing equipment.
PRESSURIZED EQUIPMENT HAZARD
Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and
cause serious injury.
• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking, or servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers and other body parts.
• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.

WARNING
310928A 3
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
• Use water-based materials. Use fluids and solvents that are compatible with equipment wetted parts.
See
Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings.
• Check equipment daily. Repair or replace worn or damaged parts immediately.
• Do not alter or modify equipment.
• For professional use only.
• Use equipment only for its intended purpose. Call your Graco distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not use hoses to pull equipment.
• Comply with all applicable safety regulations.
PRESSURIZED ALUMINUM PARTS HAZARD
Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids
containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical
reaction and equipment rupture, and result in death, serious injury, and property damage.
SUCTION HAZARD
Never place hands near the pump fluid inlet when pump is operating or pressurized. Powerful suction
could cause serious injury.
CARBON MONOXIDE HAZARD
Exhaust contains poisonous carbon monoxide, which is colorless and odorless. Breathing carbon mon-
oxide can cause death. Do not operate in an enclosed area.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
• Read MSDS’s to know the specific hazards of the fluids you are using.
• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
BURN HAZARD
Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe
burns, do not touch hot fluid or equipment. Wait until equipment/fluid has cooled completely.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss. This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and solvent manufacturer
•Gloves
• Hearing protection
WARNING

4310928A
English Français Deutsch Español Italiano
1 Striper OFF
2 Stencil Lever
3 Spray gun control
4Primevalve
5 Spray gun trigger lock
6 Spray shield
7Pump
8 Drain tube
9 Suction tube
10 Fluid filter
11 Tip extension, 30 in.







35,0(
635$<




WLD

Setup
310928A 5
Setup
1 Take sprayer out of box. Fold
handle up.
2 Tighten knob and secure
handle
3 Check engine oil level. See
Honda engine manual.
4 Fill fuel tank. See Honda
engine manual.
WLD
WLD
FROG
WLD
WLD

Setup
6310928A
5 Assemble spray shields to
striper
6 Loosen knob and slide
spray gun outside of wheel.
Tighten knob.
7 Fill wet cup with TSL to
extend pump life
8 Ensure tip guard and
SwitchTip are removed
WLD
WLD
WLD
WLD
WLD
WLD

Setup
310928A 7
9 Place suction tube in water
pail
10 Place drain tube in waste
pail
11 Turn prime valve down
:$7(5
WLD
:$67(
WLD
WLD

Startup
8310928A
Startup
1 Start engine.
a Press priming bulb (A)
repeatedly until gasoline is
seen in fuel return tube (B)
if engine is cold or has pre-
viously run out of fuel
b Move choke to closed c Pull starter rope d After engine starts, move
choke to open. Let sprayer
run for 20 seconds.
WLD
WLD
$
%
WLD
WLD
WLD

Startup
310928A 9
2 Ensure pump is cycling. If
not, momentarily squeeze
gun control.
3 Allow pump to prime until
water comes out of drain
tube
4 Turn engine OFF 5 Prepare paint according to
specification of paint manu-
facturer
WLD
WLD
:$67(
WLD
2))
WLD
3$,17
:$7(5
WLD

Startup
10 310928A
6 Place suction tube in paint 7 Start engine 8 Ensure pump is cycling. If
not, momentarily squeeze
spray gun control.
9 Allow pump to prime until
paint comes out of drain
tube
:$67(
3$,17
WLD
WLD
WLD
WLD
:$67(
WLD