Grant-bio CPS-20 User manual

Compact CO2Platform Shaker
CPS-20
Operating Manual

Edition 1.01 –December of 2021 Compact CO2Platform Shaker CPS-20
Page 2 Operating manual

Compact CO2Platform Shaker CPS-20 Edition 1.01 –December of 2021
Operating manual Page 3
Contents
1. About this edition of user instructions .....................................................................................3
2. Safety precautions..................................................................................................................4
3. General information................................................................................................................5
4. Getting started........................................................................................................................6
5. Operation...............................................................................................................................8
6. Specifications.........................................................................................................................9
7. Ordering information...............................................................................................................9
8. Guarantee and Service.........................................................................................................10
9. Compliance..........................................................................................................................11
1. About this edition of user instructions
The current edition of user instructions applies to following models:
Model
Version
CPS-20, compact CO2platform shaker
V.1GW

Edition 1.01 –December of 2021 Compact CO2Platform Shaker CPS-20
Page 4 Operating manual
2. Safety precautions
Caution!
Make sure you have fully read and understood the present instructions before us-
ing the equipment. Please pay special attention to sections marked by this symbol.
2.1. General safety
•Save the unit from shocks or falling.
•Store and transport the unit in a horizontal position (see package label) atambient temperatures
between -20°C and +60°C and maximum relative humidity of 80%.
•After transportation or storagekeep the unit under room temperature for 2-3 hrs before connect-
ing it to the mains.
•Before using any cleaning or decontaminationmethods except thoserecommended by the man-
ufacturer, check with the manufacturer that the proposed method will not damage the equip-
ment.
•Do not make modifications in design of the unit.
•The safety of the equipment may be impaired if the equipment is used with accessories not
specified by the manufacturer or if the equipment is used in a manner not specified by the man-
ufacturer.
•Hazards may occur if the equipment is used to mix flammable or explosive materials.
•Do not mix materials where the transfer of mechanical energy to glass could lead to a breakage.
2.2. Electrical safety
•Connect only to external power supply with voltage corresponding to that on the serial number
label.
•Use only the external power supply provided with this product.
•Ensure that the external power supply is easily accessible during use.
•Disconnect the unit from the mains before moving.
•Turn off the unit by disconnecting the external power supply from the power socket.
•If liquid penetrates into the unit, disconnect it from the power socket and have it checked by a
repair and maintenance technician.
•Do not operate the unit in premises where condensation can form. Operating conditions of the
unit are defined in the Specifications section.
2.3. During operation
•Do not impede the platform motion.
•Do not operate the unit in environments with aggressive or explosive chemical mixtures. Please
contact manufacturer for possible operation of the unit in specific atmospheres.
•Do not operate the unit if it is faulty or has been installed incorrectly.
•Do not use outside laboratory rooms.
•Do not place a loadexceedingthe maximum loadvalue mentioned inthe Specifications section
of these instructions.
2.4. Biological safety
•It is the user’s responsibility to carry out appropriate decontamination if hazardous material is
spilt on or penetrates into the equipment.

Compact CO2Platform Shaker CPS-20 Edition 1.01 –December of 2021
Operating manual Page 5
3. General information
CO2Shaker CPS-20 provides regulated orbital motion of the platform and is designed for use
specifically in CO2incubators. CPS-20 is specifically designed for use in harsh environments such as
CO2and humidity and provides reproducible results for cellculture growth. A choiceof 5 interchangeable
platforms provides the possibility of performing various procedures and techniques in various cultivation
vessels. The specially designedremote controller allows for protection of electronics from CO2incubator
environment, as well as, does not interfere with the experiment.
Shaker CPS-20 incorporates a brushless motor with a guaranteed service life up to 35,000
hours. The unit is equipped with a triple eccentric mechanism for platform motion that provides supreme
balancing characteristics, superior reliability and quiet operation. Typical applications include eukaryotic
cells cultivation.

Edition 1.01 –December of 2021 Compact CO2Platform Shaker CPS-20
Page 6 Operating manual
4. Getting started
4.1. Unpacking. Remove packing materials carefully and retain them for future shipment or storage of
the unit. Examine the unit carefully for any damage incurred during transit. The warranty does not
cover in-transit damage. Warranty covers only the units transported in the original package.
4.2. Complete set. Package contents:
4.2.1. Standard set
- CPS-20 Orbital Shaker .................................................................................................1 piece
- External power supply ..................................................................................................1 piece
- Remote controller..........................................................................................................1 piece
- Operating instructions, declaration of conformity ............................................................1 copy
4.2.2. Optional accessories
- UP-12 platform........................................................................................................on request
- Additional HB-200 holding bar for UP-12 platform ...................................................on request
- Bio PP-4 platform.................................................................................................... on request
- P-16/88 platform...................................................................................................... on request
- P-12/100 platform.................................................................................................... on request
- P-6/250 platform...................................................................................................... on request
UP-12 Bio PP-4 P-16/88
P-12/100 P-6/250

Compact CO2Platform Shaker CPS-20 Edition 1.01 –December of 2021
Operating manual Page 7
4.3. Platform installation. Install the platform to the moving base of the shaking unit. Fit the pins on the
underside of the platform into the holes on the moving base.
4.4. Setup.
Note.
The CO2incubator must be not operating, switched off and in non-condensing en-
vironment during the installation of CO2shaker.
- Gently pull the control cable apart at the middle connector.
- Thread the longer part of the control cable (connected to the shaking unit) through the opening
port in the CO2incubator, from inside to outside.
- Seal the opening as shown by the instructions for the incubator (e.g., with PE seal that comes
with the CO2incubator)
- Place the shaking unit inside the CO2incubator positioned on an even horizontal and firm sur-
face place. Make sure that the control cable does not obstruct the movement of the platform.
- Accurately connect the control cable in the middle, outside of the CO2incubator. Align ends by
the white marking on the rim. Do not force the connection.
- Remove protective film from the display.
- Plug the external power supply into the 12 V socket at the bottom of the unit controller and po-
sition the power supply so that the plug is easily accessible.
- The unit controller features magnets on the back. If possible and necessary, put the unit con-
troller on the outer wall or a door of the CO2incubator.

Edition 1.01 –December of 2021 Compact CO2Platform Shaker CPS-20
Page 8 Operating manual
5. Operation
Figure 1. Control panel of CPS-20
5.1. Connect the external power supply to the mains. Display turns on.
5.2. Place samples on the unit platform.
5.3. Setting the parameters. Press the Select key (fig. 1/1) to choose the parameter to change. Each
pressing of the Select key consecutively activates the parameters. The active parameter is flashing.
Use the ▼ and ▲ keys (fig. 1/2) to set the necessary value. Pressing the key for more than 2 s
increases the speed of value change.
5.3.1. Set the required working time interval in hours and minutes, the increment is 1 minute.
5.3.2. Set the required shaking speed, the increment is 10 rpm.
5.4. Press the Run Stop key (fig. 1/3). The platform starts rotation, indication RUN appears on display
and the timer in the lower line of the display starts counting the time interval.
5.5. After the timer reaches the set time, the platform motion will stop and the flashing indication STOP,
accompaniedbythe repetitive sound signal, will appear in the lower lineof thedisplay.Press the Run
Stop key to shut down the signal.
5.6. The unit can be stopped before the set time elapses if necessary by pressing the Run Stop key.
Press the Run Stop key to repeat the operation with the same working time and speed.
5.7. If the working time is not set (or is reset) and the Time indicator on display shows OFF, pressing the
Run Stop key will start continuous operation of the unit until the Run Stop key is pressed.
5.8. The platform motion can be stopped at any time by pressing the Run Stop key. In this case, the
program realization and the platform motion will stop and the unit will switch into the STOP mode.
5.9. After finishing the operation disconnect the external power supply from the mains.

Compact CO2Platform Shaker CPS-20 Edition 1.01 –December of 2021
Operating manual Page 9
6. Specifications
The shaking unit (without the unit controller) is designed specifically for operation in CO2incu-
bators and closed laboratory environments at ambient temperature from +4°C to +45°C in a non-con-
densing atmosphere and relative humidity up to 98%.
The unit controller is designed for operation in cold rooms, incubators (excluding CO2incuba-
tors) and closed laboratory rooms at ambient temperature from +4°C to +40°C in a non-condensing
atmosphere and relative humidity up to 80% for temperatures for temperatures up to 31°C decreasing
linearly to 50% relative humidity at 40°C.
Grant is committed to a continuous programme of improvement and reserves the right to alter
design and specifications of the equipment without additional notice.
Speed control range
1
........................................................................................................50-250 RPM
Increment.................................................................................................................................10 RPM
Digital time setting ..........................................................................................1 min –96 h or non-stop
Increment................................................................................................................................ 1 minute
Maximum load...............................................................................................................................3 kg
Orbit...........................................................................................................................................20 mm
Dimensions of the shaking unit, WxDxH ...................................................................255x255x100 mm
Operating voltage and current....................................................................................DC 12 V, 470 mA
Power consumption .....................................................................................................................5.7 W
External power supply.................................................. input AC 100-240 V, 50/60 Hz, output DC 12 V
Weight
2
....................................................................................................................................... 4.2 kg
7. Ordering information
7.1. Models and versions available:
CPS-20, compact CO2platform shaker
7.2. To inquire about or order the optional accessories, contact Grant or your local Grant representative.
7.2.1. Optional accessories:
UP-12, universal platform with bars and non-slip rubber mat (285x215 mm)
Bio PP-4, flat platform with non-slip silicone mat (255x255 mm, work area 230x230 mm)
P-12/100, platform with 12 clamps for 100 ml flasks (250x190 mm)
P-6/250, platform with 6 clamps for 250 ml flasks (250x190 mm)
P-16/88, platform with Spring holder for 88 of 10 to 50 ml tubes
HB-200, additional holding bar for UP-12
1
Maximum speed depends on the load on the platform and the shape of the vessels.
2
Accurate within ±10%.

Edition 1.01 –December of 2021 Compact CO2Platform Shaker CPS-20
Page 10 Operating manual
8. Guarantee and Service
8.1. Guarantee. When usedinlaboratory conditionsandaccordingtothisOperatingManual, thisproduct
isguaranteedforTWOYEARS (excludingitemsmentioned intables2and3)againstfaultymaterials
or workmanship.
8.2. Service. Thereare nouser-serviceable parts inside the unit. For all maintenance and repairs (except
as defined below) return to our service department in the UK or in other countries, our distributor.
8.3. Cleaning and disinfection.
8.3.1. Cleaning the outside parts. Use mild soap and water with a soft cloth or sponge for cleaning the
exterior. Rinse remaining washing solution with distilled water. Wipe dry the excess water with clean,
soft cloth or sponge.
8.3.2. Disinfecting the exterior plastic parts. Use 75% ethanol or DNA/RNA removing solution (e.g.,
PDS-250). After disinfecting it is necessary to wipe the surfaces dry.
8.3.3. Autoclaving. The platforms andits accessories are autoclavable, 15 min at 121 °C. The unit and the
unit controller are not autoclavable.

Compact CO2Platform Shaker CPS-20 Edition 1.01 –December of 2021
Operating manual Page 11
9. Compliance
EU Declaration of Conformity
All the products covered by this Manual comply with the requirements of the EU harmonised legisla-
tion verified using the following standards
Low Voltage Directive (2014/35/EC) for Electrical safety.
LVS EN 61010 Part 1
LVS EN 61010 Part 2-051
EMC directive (2014/30/EC) for Electromagnetic compatibility
LVS EN 61326-1
RoHS Directive (Directive 2011/65/EC including 2015/863)
for Hazardous substances
LVS EN50581
UK Declaration of Conformity
All the products covered by this Manual comply with the requirements of UK statutory requirements
verified using the following standards.
Electrical Equipment (Safety) Regulations 2016
BS EN 61010 Part 1
BS EN 61010 Part 2-051
Electromagnetic Compatibility Regulations 2016
BS EN 61326-1
The Restriction of the Use of Certain Substances in Electrical and
Electronic equipment Regulations 2012
BS EN50581
Waste Electrical and Electronic Equipment (WEEE)
All the products covered by this Manual are marked with the crossed-out wheelie bin sym-
bol indicating they must not be disposed of with unsorted waste. Safe recycling of WEEE
helps conserve natural resources and protect human health.
Grant Instruments complies fully with the UK Waste Electrical & Electronic Equipment
(WEEE) regulations 2013. We are a member of the B2B compliance scheme (Scheme
Approval Number WEE/MP3338PT/SCH), which handle our WEEE obligations on our be-
half. Grant Instruments have been issued with a unique registration number by the Environmental
Agency, this reference number is WEE/GA0048TZ.
For information regarding WEEE collections in the UK please contact our B2B Compliance Scheme
directly on 01691 676 124 or www.b2bcompliance.org.uk
In the EU, Grant Instruments complies with WEEE Directive 2012/19/EU.
Contact your local equipment supplier for WEEE collections.
REACH Regulations
This product does not contain any Substances of Very High Concern (SVHCs) at greater than 0.1%
that have to be identified in accordance with Regulation (EC) No 1907/2006 and therefore does not
have an entry in the SCIP database.

Grant Instruments
(Cambridge) Ltd
Shepreth
Cambridgeshire
SG8 6GB
UK
Tel: [phone]
Email: [e-mail]
www.grantinstruments.com
Representative in the European Union
Grant Instruments Europe B.V
Strawinskylaan 411
WTC, Tower A, 4th Floor
1077 XX Amsterdam
The Netherlands
Email: [email protected]antinstruments.com
Compact CO2platform shaker / CPS-20 / 1.01