Grant-bio Platform Rocker PMR-100 User manual

Operating instructions
Platform Rocker
PMR-100
For version V.1GW

Page 2
Platform Rocker PMR-100
Operating instructions
Version 1.02 - April 2013

Page 3
Contents
1 Safety .....................................................................................4
2 General Information..............................................................5
3 Getting Started......................................................................6
4 Operation of PMR-100 ..........................................................7
5 Specifications .......................................................................9
6 Guarantee and service .......................................................10
Platform Rocker PMR-100
Operating instructions
Version 1.02 - April 2013

Page 4
The following symbol means:
Caution! Read these operating instructions fully before use and pay particular attention to sections
containing this symbol.
GENERAL SAFETY
Operation of the unit must be carried out according to the given operating manual.
The unit should not be used if dropped or damaged.
The unit must be stored and transported only in a horizontal position (see marking on the package).
After transport or storage dry out the unit (2-3 hrs) before connecting it to the supply voltage.
Before using any cleaning or decontamination method except those recommended by the manufacturer,
user should check with the manufacturer that the proposed method will not damage the equipment.
Do not attempt to modify the unit.
ELECTRICAL SAFETY
Connect only to a power supply with voltage corresponding to that on the serial number label.
Do not plug the unit into the main outlet without grounding, and do not use extension lead without
grounding.
Only use the external power supply unit provided with this product.
Ensure that the external power supply connector is easily accessible during use.
Before moving, disconnect from the mains. To turn off the unit, disconnect the external power supply
from the mains outlet.
If liquid is spilled inside the unit, disconnect it from the mains and have it checked by a competent
person.
DURING OPERATION
Do not impede the platform motion during operation.
No objects or body parts can be placed between the platform and shaker body at any time.
Do not operate the unit in environments with aggressive or explosive chemical mixtures.
Do not operate the unit if it is faulty or been incorrectly installed.
For indoor use only.
Do not use outside laboratory rooms.
Do not place a load exceeding maximum loading mentioned in ref p9 Specifications.
BIOLOGICAL SAFETY
It is the user's responsibility to carry out appropriate decontamination if hazardous material is spilt on or
inside the equipment.
1. Safety
Platform Rocker PMR-100
Operating instructions
Version 1.02 - April 2013

Page 5
2. General Information
Platform Rocker PMR-100 provides adjustable soft (intensive) biological media or
solutions mixing in vessels or single use plastic bags located on the platform.
Regulated speed and angle of the platform allow flexible mixing processes according to
the method required.
Ideal for gel washing, staining/destaining after DNA/RNA or protein electrophoresis.
Optimal for biomolecular hybridization on strips and for staining/distaining procedures.
The PMR-100 can be installed inside an incubator, ideal for cell growth in single use
plastic bags (working volumes of bags 5 litres).
Platform Rocker PMR-100 is equipped with a system of platform overload automatic
detection. In the case of overload an error message is shown on the unit’s display
accompanied by the sound signal. This feature ensures long-term safe operation.
Platform Rocker PMR-100
Operating instructions
Version 1.02 - April 2013

Page 6
3. Getting started
3.1.Unpacking
Remove packaging, and retain for future shipment or storage of the unit.
3.2. The PMR-100 set includes:
• Platform Rocker PMR-100...............................................................................1 piece
• Detachable platform .......................................................................................1 piece
• Rubber pad .....................................................................................................1 piece
• Four screws and a hex key .................................................................................1 set
• External power supply unit ..............................................................................1 piece
• Operating instructions; Declaration of conformity.............................................1 copy
•
•
•
•
•
•
3.3. Set up:
place the unit on an even firm stable horizontal surface;
connect the power cord to the external power supply;
plug the external power supply unit into the 12 V socket at the rear side of the unit.
3.4. Platform installation:
install the platform on the unit and remove the rubber pad;
secure the platform on the supporting platform on top of the unit with the four
supplied screws;
cover the platform with the rubber mat.
Platform Rocker PMR-100
Operating instructions
Version 1.02 - April 2013

Page 7
4. Operation of PMR-100
4.1. Connect external power supply plug to the grounded mains.
4.2. The display will turn on with the upper line showing time, RPM and tilt angle set earlier (fig.1/u)
and the lower line showing current readings of the same parameters (fig.1/v).
How to set the necessary parameters.
Use the readings in the upper line of the display, while setting the necessary parameters.
4.3. Time set (Time hr:min)
With the help of the “p” and “q“ TIME keys (Fig. 1/w) set the required working time interval in
hours and minutes (increment - 1 min). If the button is pressed for longer time the speed of
increment becomes bigger.
Note! If the operation time is not set and the timer indicator shows 0:00, pressing RUN key
(Fig. 1/z) will allow continuous use until the STOP key (Fig. 1/{) is pressed again.
4.4. Speed set (Speed RPM)
With the help of the “p” and “q“ SPEED keys (Fig. 1/x) set the required rocking intensity in
revolutions per minute (increment 1 oscill/min). If the button is pressed for longer time the
speed of increment becomes bigger.
4.5. Tilt angle set (Angle Deg.)
With the help of the “p” and “q“ ANGLE keys (Fig. 1/y) set the necessary angle (increment
1º). If the button is pressed for longer time the speed of increment becomes bigger.
Run/Stop
OFF
30 90 10
90 10
SPEED ANGLE
RUN
STOP
Time
(hr:min)
Speed
(RPM)
Angle
(Deg.)
Fig.1. Control panel
Platform Rocker PMR-100
Operating instructions
Version 1.02 - April 2013

The set parameters can also be changed during operation.
Program execution
4.6. Place samples on the platform. When loading arrange symmetrically to the turning axis to give
the unit even balance during operation.
Caution! Do not place any items between the platform and the shaker body as this could cause
breakage or injury.
4.7. Press the RUN key (Fig. 1/z). The platform will start rocking and the timer indicator will start
counting up the time interval (with 1 min precision).
4.8. If the platform is overloaded, the operation process tries to restart rocking three times
(indication: DRIVER ERROR), if this operation fails, the display shows the flashing reading
OVERLOAD accompanied by the repetitive sound signal until the STOP key (Fig. 1/{) is
pressed. Eliminate the causes of overload before restarting operation (see p. 4.6).
4.9. After the set time elapses the platform motion stops and the timer shows the flashing reading
STOP accompanied by the repetitive sound signal until the STOP key is pressed.
4.10. If necessary the unit can be stopped at any time during operation before the set time has
elapsed by pressing the STOP key. In this case the platform motion stops when the platform
achieves horizontal position. Pressing the RUN key again will start the program from the
beginning (timer will be restarted).
4.11. At the end of operation disconnect the external power supply unit from the mains.
Page 8
Platform Rocker PMR-100
Operating instructions
Version 1.02 - April 2013

5. Specifications
The product is designed for operation indoors in a laboratory at altitudes up to 2000 m,
with ambient temperature from +4°C to +40°C and maximum relative humidity 80% for
temperatures up to 31°C decreasing linearly to 50% relative humidity at 40°C.
·Speed control range ...........................................................................1-99 oscill/min
·Speed setting range ................................................................................1 oscill/min
·Tilt angle range
for 1-50 oscill/min range ...........................................................0 - 9°
for 51-99 oscill/min range ............................................................10°
·Digital time setting...................................................1 min - 99 hrs 59 min / non-stop
·Time setting resolution ......................................................................................1 min
·Maximum continuous operation time ............................................................168 hrs
·Maximum loading ...............................................................................................5 kg
·Platform working area ........................................................................480 x 380 mm
·Dimensions ...................................................................................400x480x250 mm
·Input current/power consumption ....................................................12V, 1,1 A / 13W
·External power supply ...................... input AC 100-240 V 50/60Hz, output DC 12V
·Weight, not more ..............................................................................................13 kg
Grant is committed to a continuous programme of improvement, specifications may be
changed without notice.
Page 9
DescriptionReplacement parts
Flat platform with non-slip rubber matPP-480
Platform Rocker PMR-100
Operating instructions
Version 1.02 - April 2013

6. Guarantee and Service
6.1.Guarantee
When used in laboratory conditions and according to these working instructions, this
product is guaranteed for TWO YEARS against faulty materials or workmanship.
6.2.Service & Maintenance
There are no user-serviceable parts inside the unit. For all maintenance and repairs (except
as defined below) return to our service department in the UK or in other countries, our
distributor.
6.3. Cleaning & Disinfection
Cleaning liquids that do not contain concentrated organic solvents, alkali or acid can be used
for cleaning the device. Standard ethanol (75%) can be used for disinfection. Before using
any other cleaning or decontamination method, check with the manufacturer or supplier to
make sure that the proposed method will not damage the equipment.
Page 10
Platform Rocker PMR-100
Operating instructions
Version 1.02 - April 2013

Page 11
Platform Rocker PMR-100
Operating instructions
Version 1.02 - April 2013

Platform Rocker/PMR-100/1.02
Grant Instruments
(Cambridge) Ltd
Shepreth
Cambridgeshire
SG8 6GB
UK
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.grantinstruments.com