Grant-bio PMS-1000i User manual

Microplate shaker
PMS-1000i
Operating instructions

Version 1.01 - January 2013
Page 2 Microplate shaker PMS-1000i
Operating instructions

Contents
1 Safety
2 General Information
3 Getting Started
4 Operation of PMS-1000i
5 Specifications
6 Guarantee and service
Microplate shaker PMS-1000i
Operating instructions Version 1.01 - January 2013
Page 3

1. Safety
The following symbols mean:
Caution! Read these operating instructions fully before use and pay particular
attention to sections containing this symbol.
GENERAL SAFETY
Use only as specified in the operating instructions provided.
The unit should not be used if dropped or damaged.
The unit must be stored and transported in a horizontal position (see package label).
After transport or storage in humid conditions allow the unit to dry out (2-3 hrs) before connecting to
the supply voltage.
Before using any cleaning or decontamination method except those recommended by the
manufacturer, check with the manufacturer that the proposed method will not damage the
equipment.
Do not attempt to modify the unit.
ELECTRICAL SAFETY
Connect only to a power supply with a voltage corresponding to that on the serial number label.
Use only the external power supply unit provided with this product.
Ensure that the power switch and external power supply connector are easily accessible during
use.
Before moving the unit, disconnect it from the mains.
To turn off the unit, disconnect the external power supply from the power outlet.
If liquid is spilled inside the unit, disconnect it from the mains and have it checked by a competent
person.
DURING OPERATION
Do not impede the platform motion.
Do not operate the unit in environments with aggressive or explosive chemical mixtures.
Do not operate the unit if it is faulty or been incorrectly installed.
For indoor use only.
Do not use outside laboratory rooms.
Do not place a load exceeding maximum loading mentioned in Specifications.
BIOLOGICAL SAFETY
It is the user's responsibility to carry out appropriate decontamination if hazardous material is spilt on
or inside the equipment.
Version 1.01 - January 2013
Page 4 Microplate shaker PMS-1000i
Operating instructions

2. General Information
The new upgraded PMS-1000i version is designed for reliable continuous, long-
term operation. Use of direct drive and brushless motor allows continuous
mixing during up to 7 days and guarantees reliable operation for more than 2
years.
The Microplate shaker PMS-1000i is designed to regulate shaking for 2 or 4, 96-
well microplates. Compact with a low profile and small footprint for personal
use, applications include, immuno-diagnostics, mixing of biological liquids as
well as incubation and cultivation in microplates according to the program set by
the operator.
The unit can also be used for mixing any biological and chemical
components, in all areas of medicine, biotechnology and microbiology
laboratory research.
The principle of the PMS-1000i operation is based on the creation of the
rotational movement of the shaker platform with smooth, constant amplitude.
The rotational speed is controlled from the front panel.
Gentle shaking of samples
Smooth regulation and stabilization of the rotational speed
Even shaking amplitude throughout the shaker platform
Setting and indication of the necessary working time
Automatic stop of platform movement after the time expires
Indication of the current operation time
Microplate shaker PMS-1000i
Operating instructions Version 1.01 - January 2013
Page 5

3. Getting started
3.1 Unpacking
Remove packaging carefully and retain for future shipment or storage of the unit. Examine
the unit carefully for any damage incurred during transit. The warranty does not cover in-
transit damage.
3.2 The PMS-1000i set includes:
• Microplate shaker PMS-1000i.................................................................1 piece
• Platform for 2 plates ..............................................................................1 piece
• Operating instructions; Declaration of Conformity .....................................1 copy
• External power supply ..............................................................................1 piece
3.3 Optional extras
Platform MPP4 for 4 microtest plates 
3.4 Set up:
• place the unit on an even horizontal working surface;
• plug the external power supply unit into the 12 V socket at the rear side of the unit.
3.5 Platform installation
Install the platform by inserting the pins on the underside of the platform into the holes on
the supporting platform on the shaker.
Note! When using MPP4 platform do not set speed higher than 800 rpm.
2 plate standard platform 4 plate option MPP4
Version 1.01 - January 2013
Page 6 Microplate shaker PMS-1000i
Operating instructions

4. Operation of PMS-1000i
Fig.1 Control panel
4.1. Connect external power supply to the mains.
4.2. Place the microtest plates on the platform and fix them with the 2 screws. Using MPP4
platform fix the microtest plates with the special holder by pressing it against the microtest
plates with two screws.
4.3. Switch ON the Power switch (Fig.1/1), located on the front panel of the shaker (the timer
indicator will be light up (Fig.1/3), in standby mode the display shows set time or set speed
(when RPM key is pressed). In run mode the display shows operation time or actual speed
(when RPM key is pressed)
4.4. Using the ▲ and ▼ buttons (Fig.1/4) set the working time with the help of the timer display.
The set time is displayed in hours and minutes (hh:mm).
4.5. Set the shaking speed with the Speed dial (Fig. 1/6) using set speed readings on the
display. Speed readings are indicated on the display while the Speed knob is being
turned.
Microplate shaker PMS-1000i
Operating instructions Version 1.01 - January 2013
Page 7

4.6. Press the Run/Stop key (Fig. 1/5). The platform begins shaking and the timer indicator
starts counting up the set time interval. The timer displays the actual time: up to 1 hour - in
minutes and seconds (min:sec), after 1 hour - in hours and minutes (hh:mm). Press and
hold the RPM key (Fig. 1/2) while the platform is shaking to display the actual speed of the
platform motion on the display.
4.7. After the set time has expired, the platform shaking stops and the set working time is
shown on the timer display.
4.8. To repeat the operation with the same working time and speed press the Run/Stop key.
4.9. If necessary the shaker can be stopped before the set time elapses by pressing the
Run/Stop key (Fig. 1/5). For 2 s the display will be showing the time the shaker has
worked, after that, the set time.
4.10. If the working time is not set (or is deleted) and the display shows 00:00, pressing the
Run/Stop key will start continuous shaking until the Run/Stop key is pressed again.The
timer will count up until 99hrs and 59 min and then restart from 00:00.
4.11. At the end of operation turn the Power switch into position OFF.
4.12. Disconnect external power supply from the mains.
Version 1.01 - January 2013
Page 8 Microplate shaker PMS-1000i
Operating instructions

5. Specifications
The PMS-1000i is designed for operation indoors in a laboratory, cold room or incubator, with an
ambient temperature from +4°C to +40°C and maximum relative humidity of 80% for temperatures
up to 31°C decreasing linearly to 50% relative humidity at 40°C. It can be used at altitudes up to
2000m.
· Speed control range ...............................................................................150-1200 rpm
(150-800 rpm using the platform MPP-4)
· Orbit ......................................................................................................................2 mm
· Digital time setting ....................................................................1 min - 24 hr / non-stop
· Maximum continuous operation time ................................................................168 hrs
· Maximum loading ................................................................................................0.3 kg
· Dimensions ........................................................................................220x205x90 mm
· Input current/power consumption .................................................12V, 280 mA / 3.4 W
· External power supply .......................... Input AC 100-240 V 50/60Hz, output DC 12V
· Weight, not more than..........................................................................................2.0 kg
Optional accessories
Description
MPP-4
platform 4 microtest plates
Replacement parts
Description
MPP-2
platform 2 microtest plates
Grant is committed to a continuous program of improvement; specifications may be changed
without notice.
Microplate shaker PMS-1000i
Operating instructions Version 1.01 - January 2013
Page 9

6. Guarantee and Service
6.1 Guarantee
When used in laboratory conditions and according to these working instructions, this
product is guaranteed for TWO YEARS against faulty materials or workmanship.
6.2 Service
There are no user-serviceable parts inside the unit. For all maintenance and repairs
return to our service department in the UK or in other countries, our distributor.
6.3 Cleaning & Disinfection
Standard ethanol (75%) or other cleaning agents recommended for cleaning of laboratory
equipment can be used for cleaning and disinfection of the unit
Version 1.01 - January 2013
Page 10 Microplate shaker PMS-1000i
Operating instructions

Microplate shaker PMS-1000i
Operating instructions Version 1.01 - January 2013
Page 11

Grant Instruments
(Cambridge) Ltd
Shepreth
Cambridgeshire
SG8 6GB
UK
Tel: [phone]
Fax: [phone]
Email:[email protected]
www.grantinstruments.com
Microplate shaker/PMS-1000i/1.01