GRAPHTEC CE5000 SERIES User manual

CE5000-UM-251-22-9370
CE 5000 Series
SERVICE MANUAL
MANUAL NO. CE5000-UM-251
CUTTING PLOTTER

CE5000-UM-251-9370 ii
HISTORY OF REVISIONS
No. Date issued Description of revision Page Edition
106.07.06 First Printing All 01
20 6 .0 9 .13 Information for the 9e60p was added. 10 -1,10-12 02
30 6 .0 9 .13 Part list for the steel stand ST0068 was added. 10-9 02
40 6 .0 9 .13
Part number for the main board of the CE5000-40 was corrected. 4-1,10-1 02
506.09.26 Procedure of upgrading the system firmware was corrected. 7-13 03
606.09.26 Section numbers were corrected. 11-10 to 11-12 03
70 6.11.07 Procedure of adjusting the pen force was corrected. 7-4 04
80 6.11.16 Hooter of page was wrong. 4-1 05
90 6.11.16 Cutting Mat 40 of part number was updated. 4 -1,10 - 3 05
10 0 6.11.16 Cutting Mat 120 of part number was updated. 4 -1,10 - 3 05
11 07. 02 . 2 8 Part number for the cutter pen holder was corrected. 10-6 06
12 07. 02 . 2 8
The cutter pen holder and the pen holder thumb screw L10 were deleted from recommended parts list. 4-1 06
13 07.05.18 CE5000-120AP information added. All 07
14 07.10.19
Remark of the Main Board of CE5000-120AP was corrected. 4-1 08
15 08.03.04 Description for the roll stocker was corrected. 10 -15 09
16 08.08.22
Procedure of adjusting the Auto-Registration Mark Sensor Sensitivity was added. 7-10 10
17 08.10. 28 Rank of parts were corrected. 10-1 to 10-16 11
18 08.11.04 X and Y motor cables were added to the parts list. 10-9 12
19 08.12.15
Part number for the Auto registration mark sensor was corrected. 4 -1,10 -7 13
20 08.12.15
The X-drive belt for CE5000-40 and -60 were changed. 10-3 13
21 08.12.15
The replacing procedure was added for the X-drive belt of the CE5000-40 and the CE5000-60. 6-27 13
22 08.12.15 Part number was added for the stopper assembly. 10 -12 13
23 09.01.09 Procedure of the distance adjustment was corrected. 7-7 14
24 09.04.02 Part number for the stock shaft was corrected. 10-10,10-11 15
25 09.04.02 Part number for the stopper was corrected. 10-10 15
26 09.04.02 The explanation of the sensor status were corrected. 8-1 15
27 09.08.24 Part number for the Y drive pulley was corrected. 4 -1,10 - 3,10 - 5 16
28 09.08.24
Part number for the rubber spacer of CE5000-120AP was corrected. 10-5 16
29 11.03.02 The item No.38 was not including the item No.37. 10-5 17
30 11.03.03
The replacing procedure added for the new type of main board. 18
31 11.03.03 The parts number added for the new type of main board. 4-1,10-1 18
32 11.03.04
The Dip Switch setting added for the new type of main board. 7-1 18
33 11.03.07 The circuit diagrams added for the new type of main board. 11-13 to 11-18 18
34 11.03.07 Confirmation for the Y rail mounting position is added. 6-38 to 6-40 18
35 11.03.07 The adjusting procedure added for the drive roller height. 6-41 to 6-43 18
36 11.05.16
The dip-switch setting for the NV-RAM Clear of new type of main board was corrected. 7-1,7-4 19
37 11.05.16
The menu and procedure were corrected for updating the firmware of new main board. 7-16 19
38 11.05.16
The procedure was corrected for replacing the new type of main board . 6-34 19
39 11.08.01 The parts number of LCD changed. 4-1,10-1 20
40 11.10.11 The baearing added for the CE5000-120AP-AMJ 10-5 21
41 11.10.11 The parts number changed for the rubber spacer. 10-5 21
42 11.10.11 The parts number added for the new type of main board. 10-6 21
43 12.01.06 The measuring position of pen block height was added. 6-16 21
44 12.11.22 Part number for the tension spring was corrected. 10-5 22
45 12.11.22 Part number for the center bar 120AP was corrected. 10 -13 22
46 13.02.20 Part number for the Push Roller was corrected. 4 -1,10 - 3,10 - 5 22
47 13.02.20 Part number for the Y Belt 40 was corrected. 4 -1,10 -7 22
48 13.02.20 Part number for the Y Belt 60 was corrected. 4 -1,10 -7 22
49 13.02.20 Part number for the Y Belt 120 was corrected. 4 -1,10 -7 22
50 13.02.20
Part number for the Push Roller Sensor Flexible Cable was corrected. 4 -1,10 -7 22
51 13.02.20
Part number for the X Motor for CE5000-40/60 was corrected. 4 -1,10 - 3 22
52 13.02.20
Part number for the Y Motor for CE5000-40/60/120 was corrected. 4 -1,10 - 3,10 - 5 22
53 13.02.20
Part number for the Control Panel Switch Sheet was corrected. 4-1,10-1 22

CE5000-UM-251-9370 iii
54 13.02.20 Part number for the Drive Roller 120 was corrected. 4 -1,10 - 5 22
55 13.02.20 Part number for the Drive Roller 60 was corrected. 4 -1,10 - 3 22
56 13.02.20 Part number for the Drive Roller 40 was corrected. 4 -1,10 - 3 22
57 13.02.20 Part number for the Left Side Cover was corrected. 10 -1 22
58 13.02.20 Part number for the Front Guide 60 was corrected. 10 -1 22
59 13.02.20 Part number for the Front Guide 120 V2 was corrected. 10 -1,10-5 22
60 13.02.20 Part number for the Front Guide 120AP was corrected. 10 -1,10-5 22
61 13.02.20 Part number for the Right Side Cover was corrected. 10 -1 22
62 13.02.20 Part number for the Front Guide 40 was corrected. 10 -1 22
63 13.02.20
Part number for the Center Cover CE5000-120 was corrected. 10 -1 22
64 13.02.20
Part number for the Center Cover CE5000-60 was corrected. 10 -1 22
65 13.02.20
Part number for the Center Cover CE5000-40 was corrected. 10 -1 22
66 13.02.20 Part number for the Rear Guide 120 V2 was corrected. 10-1,10-6 22
67 13.02.20 Part number for the Caution Label was corrected. 10-1 22
68 13.02.20
Part number for the Y Drive Belt 100TN15-5G was corrected. 10-3 22
69 13.02.20 Part number for the X Drive Belt 82TN15-8G was corrected. 10-3 22
70 13.02.20
Part number for the Y Drive Belt 100TN15-10G was corrected. 10-5 22
71 13.02.20
Part number for the X Drive Belt, 82TN15-10G was corrected. 10-5 22
72 13.02.20 Part number for the Cam Shaft 120 was corrected. 10-5 22
73 13.02.20 Part number for the Rubber Spacer was corrected. 10-5 22
74 13.02.20 Part number for the Spring DE-646 was corrected. 10-5 22
75 13.02.20 Part number for the Front Media Guide was corrected. 10-5 22
76 13.02.20
Part number for the Center Cover CE5000-120 was corrected. 10-622
77 13.02.20
Part number for the Thumb Screw L10 was corrected. 10-722
78 13.02.20
Part number for the Registration Mark Sensor Bracket A was corrected. 10-722
80 13.02.20
Part number for the CA504301A (Power Supply to Power Switch) was corrected. 10-9 22
81 13.02.20
Part number for the CA504310 (Power Supply to Main Board) was corrected. 10-9 22
82 13.02.20
Part number for the CA504308 (Registration Mark Sensor to Y Relay) was corrected. 10-9 22
83 13.02.20
Part number for the FPC504306 (Push Roller Sensor Flexible Cable) was corrected. 10-9 22
84 13.02.20
Part number for the CA504311 (X Motor Extension Cable) was corrected. 10-9 22
85 13.02.20
Part number for the CA504312 (X Motor Encoder Extension Cable) was corrected. 10-9 22
86 13.02.20
Part number for the CA504325 (Y-motor Encoder Cable) was corrected. 10-9 22

CE5000-UM-251-9370 iv
CONTENTS
1 INTRODUCTION .........................................................................1-1
1.1 Main Specifications ...............................................................................................................1-1
1.2 External Dimensions ............................................................................................................ 1-3
2 PARTS NAMES and FUNCTIONS ............................................ 2-1
2.1 Parts Names and Functions..................................................................................................2-1
2.2 Assembling the Stand .......................................................................................................... 2-5
2.3 Attaching the Basket (CE5000-60/120: Optional) ..............................................................2-12
3 OPERATIONS ............................................................................ 3-1
3.1 Control Panel......................................................................................................................... 3-1
3.2 Menu List ............................................................................................................................... 3-2
3.3 Description of Special Functions A..................................................................................... 3-5
3.4 Description of Special Functions B..................................................................................... 3-8
4 RECOMMENDED PARTS LIST................................................. 4-1
5 LIST OF TOOLS ........................................................................ 5-1
5.1 Tools....................................................................................................................................... 5-1
5.2 Greasing And Gluing Points ................................................................................................ 5-1
5.3 Subparts List ......................................................................................................................... 5-1
6 DISASSEMBLY AND REASSEMBLY ....................................... 6-1
6.1 Exterior Parts ........................................................................................................................ 6-1
6.1.1 How to Replace the Right Side Cover.................................................................................................... 6-1
6.1.2 How to Replace the Left Side Cover ...................................................................................................... 6-1
6.1.3 How to Replace the Center Cover (CE5000-40/60) ............................................................................... 6-2
6.1.4 How to Replace the Center Cover (CE5000-120/120AP) ...................................................................... 6-3
6.1.5 How to Replace the Front Guide (CE5000-40/60).................................................................................. 6-4
6.1.6 How to Replace the Front Guide (CE5000-120/120AP) ......................................................................... 6-5
6.1.7 How to Replace the Rear Guide ............................................................................................................. 6-8
6.2 Mechanical Parts................................................................................................................. 6-10
6.2.1 How to Replace the Front and Rear Media Sensors............................................................................6-10

CE5000-UM-251-9370 v
6.2.2 How to Replace the Push Roller............................................................................................................6-11
6.2.3 How to Replace the Push Roller Arm ...................................................................................................6-12
6.2.4 How to Replace the Cam Sensor Board ...............................................................................................6-14
6.2.5 How to Replace the Pen Block ..............................................................................................................6-15
6.2.6 How to Replace the Push Roller Sensor ..............................................................................................6-17
6.2.7 How to Replace the Y-relay Board ........................................................................................................6-18
6.2.8 How to Replace the Cutting Mat............................................................................................................6-19
6.2.9 How to Replace the Control Panel Relay Board, LCD and Membrane Switch Panel ...................... 6-20
6.2.10 How to Replace the Y-belt..................................................................................................................... 6-22
6.2.11 How to Replace the Y-motor ................................................................................................................. 6-24
6.2.12 How to Replace the X-motor................................................................................................................. 6-26
6.2.13 How to Replace the Y-flexible Cable.................................................................................................... 6-28
6.2.14 How to Replace the Vacuum Fan ......................................................................................................... 6-31
6.2.15 How to Replace the Main Board........................................................................................................... 6-32
6.2.16 How to Replace the Power Supply....................................................................................................... 6-35
6.2.17 How to Replace the Drive Roller .......................................................................................................... 6-36
6.2.18 How to Confirm the Y rail mounting position ..................................................................................... 6-38
6.2.19 How to adjust the height of the grid drive shaft ................................................................................. 6- 41
7 ELECTRICAL ADJUSTMENTS ..................................................7-1
7.1 DIP Switch Settings ...............................................................................................................7-1
7.2 List of Items Requiring Readjustment .................................................................................7-2
7.3 Explanation of the Values of the Main Board Settings.......................................................7-3
7.4 Clearing the Non-Volatile RAM ............................................................................................ 7- 4
7.5 Adjusting the Pen Force....................................................................................................... 7-5
7.6 Adjusting the Distance Accuracy .........................................................................................7-7
7.7 Inputting the Servo Gain .......................................................................................................7-9
7.8 Setting the Auto-Registration Mark Sensor Option..........................................................7-10
7.9 Adjusting the Auto-Registration Mark Sensor Sensitivity............................................... 7-11
7.10 Adjusting the Offset of the Auto-Registration Mark Sensor............................................7-12
7.11 Upgrading the System Firmware ........................................................................................7-15
7.12 Adjusting the Pen Exchange Y Direction Value (CE5000-120AP) ....................................7-17

CE5000-UM-251-9370 vi
7.13 Adjusting the Pen Exchange Height Value (CE5000-120AP).................................. 7-18
7.14 Adjusting the Spacing Between Pen 1 and Pen 2 (CE5000-120AP) ................................................... 7-19
8 SERVICE MODES...................................................................... 8-1
8.1 Sensor Test Mode ................................................................................................................. 8-1
8.2 Control Panel Membrane Switch Test Mode....................................................................... 8-2
8.3 Clear Setup Mode.................................................................................................................. 8-3
9 TROUBLESHOOTING ............................................................... 9-1
9.1 The Plotter is Turned On But Doesn’t Operate................................................................... 9-1
9.2 Media Loading Operations................................................................................................... 9-2
9.3 Cutting Operations ............................................................................................................... 9-3
10 PARTS LIST............................................................................. 10-1
10.1 Outer Casing.........................................................................................................................10-1
10.2 Main Frame for CE5000-40/60............................................................................................ 10-3
10.3 Main Frame CE5000-120/120AP.......................................................................................... 10-5
10.4 Pen Block............................................................................................................................. 10-7
10.5 Wiring Harness.................................................................................................................... 10-9
10.6 Stand (CE5000-60, CE5000-120, CE5000-120AP).............................................................10-10
10.7 Option Basket.....................................................................................................................10-15
10.8 Other Parts .........................................................................................................................10-15
11 BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS ....................11-1
11.1 Block Diagrams....................................................................................................................11-1
11.1.1 Block Diagram for CE5000-120..............................................................................................................11-1
11.1.2 Block Diagram for CE5000-40/60 ..........................................................................................................11-2
11.2 Circuit Diagrams ..................................................................................................................11-3
11.2.1 Main Board Top Section (PN5043-01A).................................................................................................11-3
11.2.2 Main Board Connector Block Section (PN5043-01A) ..........................................................................11- 4
11.2.3 Main Board CPU Block Section (PN5043-01A).....................................................................................11-5
11.2.4 Main Board Motor Drive Section (PN5043-01A)...................................................................................11- 6
11.2.5 Main Board FPGA Section (PN5043-01A) .............................................................................................11-7
11.2.6 Main Board Interface Section (PN5043-01A)........................................................................................11- 8

CE5000-UM-251-9370 vii
11.2.7 Main Board Memory Block Section (PN5043-01A) ..............................................................................11-9
11.2.8 Relay and Sensor Board Section ........................................................................................................ 11-10
11.2.9 Control Panel Membrane Switch Panel Section ................................................................................ 11-11
11.2.10 120-Relay Board Section ..................................................................................................................... 11-12
11.2.11 120-Pen Encoder Flexible Cable Section (PN5043-10)...................................................................... 11-12
11.2.12 Main Board CPU Section (PN0021-01) ................................................................................................ 11-13
11.2.13 Main Board Connector Section (PN0021-01)...................................................................................... 11-14
11.2.14 Main Board Motor Driver Section (PN0021-01) .................................................................................. 11-15
11.2.15 Main Board FPGA Section (PN0021-01) .............................................................................................. 11-16
11.2.16 Main Board I/F Section (PN0021-01).................................................................................................... 11-17
11.2.17 Main Board Memory Section (PN0021-01).......................................................................................... 11-18

CE5000-UM-251-9370 1-1
1 INTRODUCTION
1 INTRODUCTION
CAUTION
DOUBLE POLE/NEUTRAL FUSING
1.1 Main Specications
CE5000-40CRP/60/120
Item CE5000-40CRP CE5000-60 CE5000-120
CPU 32-bits CPU
Conguration Grit rolling
Drive system Digital servo
Maximum cutting area 375 mm x 50 m 603 mm x 50 m 1213 mm x 50 m
Range of guaranteed precision 356 mm x 5 m*1 584 mm x 5 m*1 1194 mm x 5 m*1
Compatible media widths Minimum: 50 mm
Maximum: 482 mm
(19 inches)
Minimum: 50 mm
Maximum: 712 mm
(28 inches)
Minimum: 85 mm
Maximum: 1346 mm
(52 inches)
Maximum media thickness 0.25 mm
Maximum cutting speed 60 cm/s (in all directions) 100 cm/s (45° direction)
Speciable cutting speeds
1–10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 cm/s 1–10, 15, 20, 25, 30, 35, 40, 45,
50, 55, 60, * cm/s
Cutting force 0.2 to 2.3 N
(20 gf to 300 gf) (31 levels)
0.2 to 4.4 N
(20 gf to 450 gf) (38 levels)
Minimum character size
Approximately 5 mm for alphanumeric characters (varies depending on the medium, font, etc.)
Mechanical resolution 0.005 mm
Programmable resolution GP-GL: 0.1/0.05/0.025/0.01 mm; HP-GLTM *2: 0.025 mm
Repeatability precision 0.1 mm or less per 2 m*1
No. of pens mountable 1 pen
Compatible cutter type Supersteel cutter blades
Compatible pen type Water-based ber-tip pens
Compatible cutting lm Marking lm (PVC, uorescent, or reective lm) up to 0.25 mm in thickness
(excluding high-luminosity reective lm)
Interfaces RS-232C/USB (Full Speed)
Buffer capacity 2 MB
Command modes GP-GL, HP-GLTM *2 (selected on the control panel)
Display panel Liquid crystal display (16 characters x 1 row)
Rated power supply 100 to 240 V AC, 50/60 Hz
Power consumption 100 VA
Operating environment 10°C to 35°C, 35% to 75% RH
Conditions for guaranteed precision 16°C to 32°C, 35% to 70% RH
External dimensions (W x D x H) Approx.
623 x 285 x 223 mm
Approx.
851 x 585 x 1004 mm
*3
Approx.
1,487 x 744 x 1194 mm
*3
Weight Approx. 9.4 kg Approx. 25 kg
*3
Approx. 39.1 kg
*3
*1: Varies depending on the type of Graphtec-authorized lm and the cutting conditions
*2: HP-GLTM is a registered trademark of Hewlett-Packard Company.
*3: Including the stand

CE5000-UM-251-9370 1-2
1 INTRODUCTION
CE5000-120AP
Item CE5000-120AP
CPU 32-bit CPU
Configuration Grit rolling
Drive system Digital servo
Maximum cutting area 1164 mm x 50 m
Maximum guaranteed cutting area 1164 mm x 3 m*1
Compatible media widths
Media widths 160 to 270, 300 to 400, 440 to 540, 580 to 680, 710 to 810, 850 to
950, 990 to 1090, 1120 to 1220 mm (the effective drawing area is the
maximum obtainable area for the corresponding medium width) Up to
1180 mm when roll media (2-inch core) is used
Maximum roll outer diameter 190 mm
Media types Fine quality paper for apparel patterns (64 to 130 g/m2)
Roll media diameter: 2-inch, 3-inch
Maximum cutting speed 60 cm/s
Specifiable cutting speeds 1 to 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 cm/s
Cutting force 20 to 300 gf (31 levels)
Mechanical resolution 0.005 mm
Programmable resolution GP-GL: 0.1/0.5/0.025/0.01 mm, HP-GLTM *3: 0.025 mm
Repeatability precision
Mechanical precision Within 0.1 mm/3m*2
Guaranteed precision Within ±0.5 mm/3 m, up to a maximum of five consecutive pages*1
(cutter pen/plotter pen exchange precision is also included)
No. of pens mountable 2
Compatible cutter blade type Supersteel
Compatible pen type Water-based fiber-tip pens, Oil-based ballpoint pen
Interfaces RS-232C/USB 2.0 (Full speed)
Buffer capacity 2 MB
Command modes GP-GL, HP-GLTM *3 (selected on the control panel)
Display panel LCD (16 characters x 1 row)
Rated power supply 100 to 240 V AC, 50/60 Hz
Power consumption 100 VA
Operating environment 10°C to 35°C, 35% to 75% RH
Conditions for guaranteed precision 16°C to 32°C, 35% to 70% RH
External dimensions (W x D x H) Approx. 1,487 x 656 x 1189 mm
Weight 43 kg
*1: When the following Graphtec-specified conditions have been met:
• Graphtec-specified paper must be used for cutting/plotting.
• “PAPER LOAD: 2” must be specified for the PAPER LOAD setting and “UNTIL: 180 seconds” for the PAPER READY
TIME setting.
• After five pages have been cut/plotted consecutively, the paper must be reloaded.
• If expansion or contraction of the paper due to temperature and/or humidity changes has occurred during a cutting
or plotting operation, the following margins of error are added to the repeatability precision value:
0.1 mm/°C, 0.3 mm/10% RH.
*2: The precision specification is the precision that was obtained when Graphtec’s mylar film was used to measure the
mechanical precision. Please note that as only fine quality pattern paper can be used with this device, the precision
may differ slightly.
*3: HP-GLTM is a registered trademark of Hewlett-Packard Company.

CE5000-UM-251-9370 1-3
1 INTRODUCTION
1.2 External Dimensions
CE5000-40CRP
623 322
285
443
322
（122 ）
Units: mm
Dimensional accuracy: ±5 mm
CE5000-60
1004
585
851
Units: mm
Dimensional accuracy: ±5 mm

CE5000-UM-251-9370 1-4
1 INTRODUCTION
CE5000-120
7441487
1194
Units: mm
Dimensional accuracy: ±5 mm
CE5000-120AP
1487
1020
1189
Units: mm
Dimensional accuracy: ±5 mm

CE5000-UM-251-9370 2-1
2 PARTS NAMES and FUNCTIONS
2 PARTS NAMES and FUNCTIONS
2.1 Parts Names and Functions
Front View
Media set lever
Pen holder
Pen carriage
Grit roller
Cutting mat
Push rollers
The above illustration is of the CE5000-120 model.
USB interface
connector
Serial (RS-232C)
interface connector
Control panel
Cutting mat : Cutting or plotting is performed on this mat.
Grit roller : Feeds the medium backward or forward
Push rollers : Push the medium against the grit roller
Pen carriage : Moves the cutter pen to the left and right
Pen holder : Holds the cutter pen and moves it up and down
Media set lever : Raises or lowers the push rollers during loading of a
medium
Control panel : Used to operate the cutting plotter and set functions
USB interface connector : Used to connect a USB cable
Serial (RS-232C) interface connector : Used to connect an RS-232C serial interface cable

CE5000-UM-251-9370 2-2
2 PARTS NAMES and FUNCTIONS
Rear View
Power switch
AC power inlet
Stock rollers
Stoppers Stand
The above illustration is of the CE5000-120 model.
AC power inlet : Connects the power cord to the cutting plotter
Power switch : Turns the power supply to the cutting plotter on or off
Stand : Supports the cutting-plotter unit
Stock rollers : Hold the roll media
Stoppers : Used to determine the position of the roll media loaded

CE5000-UM-251-9370 2-3
2 PARTS NAMES and FUNCTIONS
Front View (CE5000-120AP)
Media set lever
Control panel
Grit roller
Cutting mat
Push rollersStock shaft
Stopper
Pen station
Pen carriage
Pen holder
Cutter pen holder
USB
interface connector
Serial (RS-232C)
interface connector
Cutting mat : Cutting or plotting is performed on this mat.
Grit roller : Feeds the medium backward or forward.
Push rollers : Pushes the medium against the grit rollers.
Pen carriage : Moves the cutter pen to the left and right.
Cutter pen holder : Hold the cutter pen and moves it up and down.
Pen holder : Holds the pen and moves it up and down.
Pen station : Used to mount the pen before it is used.
Media set lever : Raises or lowers the push rollers during loading of a
medium.
Control panel : Used to operate the cutting plotter and set functions.
USB interface connector : Used to connect a USB cable.
Serial (RS-232C) interface connector : Used to connect an RS-232C serial interface cable.
Stock shaft : Used to load roll media.
Stoppers : Used to hold a roll medium in place (left and right, one
each).

CE5000-UM-251-9370 2-4
2 PARTS NAMES and FUNCTIONS
Rear View (CE5000-120AP)
Power switch
AC power inlet
Alignment shaft
Basket
Stand
AC power inlet : Connects the power cord to the cutting plotter.
Power switch : Turns the power supply to the cutting plotter on or off.
Stand : Supports the cutting-plotter unit.
Alignment shaft : Used when loading roll media.
Basket : Used to catch media after it has been cut.

CE5000-UM-251-9370 2-5
2 PARTS NAMES and FUNCTIONS
2.2 Assembling the Stand
CE5000-60/120:Standard
Stand Construction
The stand is made up of the following parts.
Stand feet (L/R)
Hexagonal socket bolt
(M5) x 12
Coin screw x 4
CE5000-60 only
Hexagonal socket bolt
(M6) x 8
CE5000-120 only
Allen wrench (M5) Allen wrench (M6)
CE5000-120 only
CE5000-60
CE5000-120
Center bar
CE5000-60
CE5000-120
Stand side bar（L/R）
CE5000-60 CE5000-120
Stand Assembly Instructions
(1) Fasten the stand feet (L/R) to the side bars (L/R) with the hexagonal socket bolts (M5), using the Allen
wrench.
Stopper
Hexagonal
socket bolt (M5)
Hexagonal
socket bolt (M5)
Stand side bar Stand side bar
Stand foot Stand foot
Front Front
CE5000-60 CE5000-120
* There are three
bolt holes, but
the center one
is not used.
(2) Fasten the stand tops (L/R) to the stand side bars (L/R) with the hexagonal socket bolts (M5), using the
Allen wrench.
CE5000-60 CE5000-120
Hexagonal
socket bolt (M5)
Stand side bar
Stand top
Hexagonal
socket bolt (M5)
Stand side bar
Stand top

CE5000-UM-251-9370 2-6
2 PARTS NAMES and FUNCTIONS
(3) Loosely fasten the stand side bars (L/R) to the center bar with the hexagonal socket bolts (CE5000-60:
M5, CE5000-120: M6), using the Allen wrench.
Hexagonal
socket bolt
(M6)
Center bar
Stand side bar
Hexagonal
socket bolt
(M6)
Center bar
Stand side bar
CE5000-60
CE5000-120
(4) Mount the CE5000 cutting plotter on the stand by inserting the positioning pins on the stand into the
positioning holes on the underside of the cutting plotter. Fasten using the four coin screws or hexagonal
socket bolts (M6).
CE5000-60
CE5000-120
Coin screws
Stand
CE5000-60
Positioning pins
Hexagonal socket
bolts (M6)
Positioning pins
Stand
CE5000-120
(5) Tighten the hexagonal socket bolts loosely fastened in step 3.

CE5000-UM-251-9370 2-7
2 PARTS NAMES and FUNCTIONS
CE5000-120AP:Standard
Stand Construction
The stand is made up of the following parts.
Stand side bar x 2 (L/R) Center bar x 1
Alignment shaft x 1
Stopper x 2 (L/R)
Hexagonal socket bolt (M6) x 8
Allen wrench (M6) x 1
Stock shaft x 1
Basket Construction
Sheet support pipe x 2
Sheet support pipe bracket x 2 Rubber cap x 4 Hexagonal socket bolt (M6) x 4
Sheet x 1

CE5000-UM-251-9370 2-8
2 PARTS NAMES and FUNCTIONS
Stand Assembly Instructions
(1) Fasten the center bar to the stand side bars (L/R) temporarily with the hexagonal socket bolts (M6),
using the Allen wrench.
Front side
Stand side bar
Center bar
Hexagonal
socket bolt (M6)
(2) Fasten the sheet support pipe brackets to the stand tops with the hexagonal socket bolts (M6).
Hexagonal socket bolt (M6)
Support pipe bracket