Green Bike Electric Motion BigDog Off Road HF 201-48N User manual
Customer Service: Green Bike – Electric Motion LLC
Main Office: 7057 Reseda Blvd ,Reseda CA 91335
Phone: (818) 578-3665
Email: [email protected]
Website: GreenBikeElectric.com
Folding(Electric(Bicycles(MODEL HF 201– 48N
Big$Dog$Off$Road$
$
Instruc4on$Manual
Green Bike – Electric Motion Congratulations on you're newly purchased!
Joining Greenbike’s Go Green revolution will open your doors to a whole new world of freedom!
Green Bike – Electric Motion greatly values the quality of our products, giving you value for your
money, friendly and professional service, and safety for the rider above all else.
Please uphold the product-customer-importer relationship to ensure a quality experience over
time. In this manual, you will find all the details required to maintain product care.
To ensure safety during riding and to maintain long-term usage experience, please read all
instructions carefully before using the bike, and follow the specified maintenance and usage
instructions.
Thank you for choosing Green Bike – Electric Motion !
- For your safety obey traffic and signage instructions!
- Do not allow an additional rider on the bike. This bike is designed to carry one person only.
Any damage to the bicycle resulting from an additional rider is not covered under warranty!
- The height of the seat and handlebars should be adjusted for maximum comfort and control
- The seat post and handlebars have a safety strip. Be sure it is not visible when adjusting. If the
strip is not set correctly, excess pressure will be created and damage the cables.!
!
- Be sure that the locking hinges of the seat and handlebars are locked before starting the trip.
- Check the condition of the brakes frequently and adjust when necessary. Braking range on a dry
road is 13 feet and on a wet road can reach 50 feet. Keep more distance on a wet road.
- The chain is properly adjusted and should not be altered. The chain must be lubricated to
prevent accelerated weathering.
- At night, the headlight and backlight must be switched on by a switch on the control display.
- Be sure to wear appropriate clothing and do not carry objects or bags in a way that they can be
caught in the wheels or chain. To keep the rider safe - do not bring your legs together (too close to
the chain) more than necessary.
- Do not ride in weather that does not allow safe riding such as rain, puddles, strong winds, snow,
etc.
- When stopping, use both brakes. Do not be content with one brake. Use both brakes together in
order to maintain stability and achieve greater control.
- Do not ride under the influence of alcohol, drugs or substances that affect the rider's alertness.
- When riding, you must hold both handles, do not perform stunts and reckless turns without
examining the area from all sides before proceeding.
- Please follow local and state regulations.
- Do not drop the bike on the ground (due to the sensitivity of the battery, motor and controller).
The bike should be placed on the kickstand carefully.
- Do not jump or climb sidewalks on the road.
Folding the Bike!
- The bike can be folded for storage at home or in the trunk of the car.!
- The folding time is only 10 seconds. You can get a demonstration at the point of purchase or
watch a tutorial video on our site www.GreenBikeElectric.com
Before You Start to Ride!
Raise the seat as shown in figure 3 and insert the battery into place and lock it.
!
Picture 3 Picture 4
LCD-S900 E-bike Intelligent Display Manual
1. Overview$of$S900$
1) UART protocol:
Equipped with independent press buttons
2) Speed：
Real-time SPEED，MAX SPEED，Average SPEED
3) Kmh/mile：
Kmh/MPH according to habit
4) Battery level：
Indicates the battery level in real time
5) Head light control：
Press button to power on/off
6) Back light adjustment：
3-level adjustment
7) Assist level：
From 0 to 5, press button to change assist level, 0-no assist, 5-default value
8) Distance：
ODO/Trip/Driving duration
9) Error code：
Please refer to appendix table 1 for definition
10)6km mode：
In this mode, it will display “WALK” on the screen
11)Parameter setting：
Set parameters, such as: wheel size, speed limit etc.
2. Presentation of screen
!
1)Speed：Average SPEED/MAX SPEED/Real-time SPEED
2)Speed unit：Kmh/MPH
3)Battery level: 5 levels, voltage interval could be customized
4)Head light icon indicates when head light and back light are on
5)Error code：“ERROR” and code when there is error
6)Assist level actual assist level 0~5, 0 –no assist, 1- ECO, 2,3-STD，4,5-POWER)
7)Distance Trip/ODO
8)6km mode
3. Press button definition
LCD-S900 uses independent press button, in total three buttons:
!“UP”、!“MODE”、!“DOWN”。
4. Operation instructions
1) Power ON/OFF
When the power is off, Long press !（MODE during 3 seconds screen will display all
contents and start to normal working mode, and controller will be turned on
When the power is on, Long press !（MODE during 3 seconds screen will be
powered offhand controller will be turned off。If no any operation both on bike and display
during 10 minutes (time could be set), the display will turn off automatically, in this case, no
power consumption for both display and controller
!
Figure 1
2) ODO/TRIP
Short press !to switch ODO/TRIP，Trip (Single trip distance) →ODO (Accumulated
distance)
!
Figure 2 Figure 3
3) Assist level
Short press !or !to change assist level default value is level
!
4) Different Speed display:
Long press !and !to switch different speed information, real time speed
(SPEED）→Max speed (MAX SPEED）→Average speed (AVGSPEED）→Driving Time。
!
5) Head light control
Long press !，turn on/off the head light。
!
6) 6km mode
When the bike is stopped, long press !, will enter 6km/h mode, the speed will be
4.5~7.5km/h according to different road conditions, “WALK” will show up on screen, long
press again !or short press !,will quit 6km/h mode. Long press or short press
could be customized by clients.
!
5. Parameter setting
When the display is powered on long press !and !，will enter parameter setting
mode (Figure 13), in this mode, can change parameter values long press again !and
!will quit parameter setting mode or no operation during 10s will also quit this mode
!
In parameter setting mode short press !/!will change parameter value short
press !will save current value and switch to next parameter
1) P01-back light lightness：
Short press !/!will switch from 1 to 3, Level 3 is lightest. Level 2 is default
value.
!
2) P02-kmh/MPH:
Short press !/!to Switch Kmh/MPH
!
3) P03-Working voltage:
Short press !/!to switch 24V, 36V, 48V, Default value is 36V
!
4)P04-Auto shutdown time:
Short press !/!to switch from 0 to 60, it is the time(in minutes) to shut down
the screen automatically if no operation 0 means never shut down, Default value is 10
minutes.
!
5)P05-Number of Assist levels:
Short press !/!to change level 0->1->2
0：3 assist levels
1：5 assist levels
2：9 assist levels
!
6)P06-Wheel size selection:
Short press !/!to switch wheel size in inch，step：0.1 inch
!
7)P07-Number of magnets for speed sensor:
Short press !/!to switch from 1 to 100
!
8)P09-Non-zero speed start:
Short press !/!to switch from0 to 1. 0：zero speed start, 1:non-zero speed
start
!
9)P10-Driving mode selection:
Short press !/!to switch from 0->1->2
0：Assist mode (throttle does not work, only assist) ；
1：Electrical driving mode (only throttle works, assist does not work)
2：Both assist and Electrical driving mode (Not available if in zero speed start and electrical
driving mode)
!
10) P11-assist sensitivity setting:
Short press !/!to switch from 1 to 24
!
11) P12-assist starting power setting:
Short press !/!to switch from 0 to 5:
!
12) P13-Assist magnetic disc types:
Short press !/!to switch from 5->8->12，different numbers of magnets
!
13) P14-Current limit for the controller:
Short press !/!to switch from 1 to 20A
!
14) P15-low voltage protection for controller:
!
Figure 29
15) P16-Reset ODO distance:
Long press !during 5 seconds
!
16) P18-Reset all parameters:
Long press !5 seconds when it displays “SSSS”，all parameters reset to default
values (except for the ODO distance)
!
6. Specifications
1) Power supply: 24V,36V,48V
2) Rated current: 10mA
3) Max current: 30mA
4) Leakage current after power off: <1uA
5) Current supply to controller:50mA
6) Working Temperature：-18~65℃
7) Storage temperature：-30~80℃
7. Error code definition
When an error appears, S900 will notice users by different codes, please refer to Table 1 for
different codes:
Code
(Decimal
)
Signification
0
Normal
6
Low Battery level
7
Motor error
8
Throttle error
Table 1
8. Notices
Power on and power off must keep an interval of at least 3 seconds, please don’t press
“MODE” button frequently when it is powered off.
When the temperature is under -10℃, the screen will be a little darker than normal, when the
temperature increases, the screen can go back to normal
9
Controller error
10
UART receive error
11
UART receive error
The Electrical System is Now Ready!
• Fold the kickstand from the ground, then sit on the seat. Put one foot on the pedal and the other
on the ground.
• Now, start pedaling and the engine will go into action. There will be a faint rustle of the pass-
through.
• To maintain battery life, do not use it until its end. When the battery meter flashes, turn off the
power switch and use the pedal as a regular bicycle. After recharging, you can ride again with the
electric motor.
• Back Injury: The rear of the bike is not intended to carry people. Maximum load is up to 25 kg,
and the luggage should be tied with straps and tested during riding.
• Park in a safe place that is not an obstacle to vehicles or pedestrians. Place the bike on the
kickstand, disconnect the power with the main switch and pull the key out of the lock.!
• The bike must be locked with a massive lock and difficult to steal. It is recommended to take the
battery with you.
• Charging: The battery must be charged only with the charger supplied with the bike.
Charging with a different charger can damage the battery and will void the warranty.!
Do not open the battery or charger for testing or repair! Bring to Green Bike Electric Motion
authorized repair shop for testing! !
• Charging takes up to 6 hours, depending on battery status. The battery can be charged both on
and off the bike.
• The charging cable must first be connected to the battery and then to the mains socket.
• When the charge indicator light is red, the battery is charging. When the charge light turns green,
the battery is full and must be disconnected from the power source. When charging, the battery
must be properly positioned and not fall or be damaged. !
• The charger becomes hot during charging. Keep it away from any flammable materials
and keep the vents unblocked!
• Be sure to properly dispose of dead batteries at proper recycling plants and do not throw away in
the trash.
• Before beginning the ride, check that all the indicator lights are working and the battery is locked
in place.
• Check that the electrical contacts of the battery are always clean. Clean with a dry cloth without
moisture.
• Check tire pressure regularly (40 PSI). Poor pressure will cause overuse of the battery and
shorten cycling time.
• Do not drive in puddles. If water enters the engine, the controller or the battery house may
become damaged. Water damage will void the warranty provided by the manufacturer.
*Store the bike in a dry place. Moisture causes corrosion! Do not leave the bike in the rain.
Immediately treat the corrosion with suitable oil! Water penetration into the electrical mechanisms
will void the warranty. !
• Do not put the bike in the sun especially when leaving the battery installed on the bike.
• Do not disassemble the electrical parts. Disassembling them independently will void the
manufacturer's warranty.
• It is important to lubricate the moving mechanical parts such as the wheel hinges, transmission
and gears, cable connections to the brake pads, etc. Do not lubricate the electrical parts
themselves!
• Brake maintenance: The right brake is responsible for braking the rear wheel. The left brake is
responsible for braking the front wheel. Always check if the brakes are normal and are optimally
tuned.
• An unintentional braking creates unnecessary and harmful resistance to the bicycle and the life
of the electrical system!
• In picture 6 you can see a stretched handle in optimal position.!
!
!
In addition, you can access any authorized bicycle shop to handle the mechanical parts of the bike
but not the electrical parts.!
The electrical parts can only be handled by a workshop authorized by the importer.
National safety regulations must be obeyed.!
The bike is designed for riding in the city and in riding paths.
For your safety, please wear a helmet!
!
Any change to the bike without the importer's approval will result in cancellation of
warranty!
Proper maintenance should be upheld by the bike owner:
!!
Bicycle Cleaning!
For the bike to serve you properly, you may want to clean it of sand and mud. If you cannot clean
the entire bike, it is necessary to clean the drive systems (chain, front and rear wheels).!
• Cleaning frequency: once in three or four significant rides or after each ride where the bike
returns with sand or mud. You can use sponge and water bucket, solvent for grease, kitchen
dishwashing sponge, rags, special brush with hard fibers.
• Rinse: Rinse all parts of the bike using a sponge. The hard brush is designed to remove heavy
dirt from the wheels, pedals, etc.
• Drying: Dry the bike with the rags and place them in direct sunlight until fully dried (preferable if
not washed at night or in stormy weather). Immediately after washing and drying, lubricate the
chain. It is recommended to clean brakes with a dedicated material for brakes.
!
Mechanical and
Electrical Components
Electronic
Specifications
Frame
Aluminum alloy
6061
Type
folding electric
bicycles
Tires
with
light
reflect
ors
Rims
aluminum
Motor : 8 Fun 750 W
20" made by
!
4" wide
!Lithium Li-On Battery 48V-16Ah Made by Boston Power U.S.A
Charger model 48-30 48V 110V-Ah
Made by SANS
Front
brake
Green Bike -
Hydraulic disk
brake
Controller :
"Smart" controller -
computerized with
pedal assist and
throttle
Rear
brake
Green Bike -
Hydraulic disk
brake
Gears
Front
fork
Made by MOZO
USA
Battery: 48 Volts 16
Amps Lithium Ion 5300
mAh manufacture by
BOSTON POWER
USA
Ergon
omic
seat
Wide adapted for
urban electric ride
with shock absorber
Intelligent Charging
Charger
(Computerized
Control) 1-6
Front
and
back !
lights
LED switch with
control switch
Built-in electric horn
Fende
rs
aluminum
alloy6061
Crank
Nickel-plated
aluminum arch
Performance:
Chain
Mph set according to
standard 19.5 mph
maximum speed with
throttle
Suspe
nsion
Double suspension
– Front fork with
suspension and
rear suspension
Taiwan Kindshock
A5 RE
The driving range for
each load is 30-60
miles per charge,
subject to road
conditions for a person
weighing up to 155 lbs.
at15 mph
Kickst
and
steel
Net weight: 61 Lbs.
Transmission 6
Made by
!
The "Crank" axis is
made by
!
Stained stainless
steel
!
Table of contents
