manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Grizzly
  6. •
  7. Lathe
  8. •
  9. Grizzly G0625 User manual

Grizzly G0625 User manual

Introduction
The Model G0625 Extension Table extends the
bed length of the Model G0624 10" Benchtop
Lathe to 38" between centers.
Inventory: (Figure 1)
A. Extension Bed ............................................ 1
B. Rubber Feet ............................................... 2
C. Cap Screws M8-1.25 x 35 .......................... 4
D. Flat Washers 8mm ..................................... 4
E. Hex Wrench 6mm ...................................... 1
Installation:
1. Install the feet into the bottom of the exten-
sion table.
2. Align the mounting holes in the extension
table and the tailstock end of the Model
G0624 bed.
3. Thread four cap screws with flat washers
through the extension table and lathe, and
finger tighten.
4. Center the tailstock over the extension table
and lathe as shown in Figure 2.
5. Tighten the cap screws with the hex wrench,
to bring the bed extension and lathe surfaces
even with the bottom of the tailstock.
6. Slide the tailstock over the bed.
—If the tailstock catches on the area where
the lathe and extension table meet, loosen
the fasteners and repeat Steps 3-5 until
the tailstock slides smoothly.
MODEL G0625
BENCHTOP LATHE
EXTENSION TABLE
INSTRUCTION SHEET
Figure 1. Model G0625 inventory.
Figure 2. Tailstock centered over extension
table and lathe.
COPYRIGHT © NOVEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL8694 PRINTED IN CHINA
A
B
C
D
E
Model
G0624
Extension
Table
7. Place a straightedge over the extension table
and lathe beds and check to see if both are
parallel and aligned.






REF PART # DESCRIPTION
1 P0625001 BED EXTENSION
2 P0625002 RUBBER FOOT
3 PN08 HEX NUT 3/8-16
4 PW01M FLAT WASHER 8MM
5 PSB40M CAP SCREW M8-1.25 X 35
6 PAW06M HEX WRENCH 6MM
Refer to the Model G0624 manual for instructions
on operating the lathe.
If you need help with your new extension table,
call our Tech Support at: (570) 546-9663.
— If the extension table tilts down, use a
strip of masking tape along the bottom
edge of the lathe to shim the table up
(Figure 3).
— If the extension table tilts up, use a strip
of masking tape along the top edge of the
lathe to shim the table down (Figure 4).
— If the extension table is skewed to the left
or right, use a vertical strip of masking tape
along the corresponding edge of the lathe
to make the extension table parallel with
the lathe (Figure 5).
Figure 3. Shimming extension table up.
Figure 4. Shimming table down.
Figure 5. Shimming table to the left.
Masking
Tape
Masking
Tape
Masking
Tape
G0625 Parts Breakdown and List
Lathe
Extension
Table
Lathe
Extension
Table
Lathe
Extension
Table

Other Grizzly Lathe manuals

Grizzly G0584 User manual

Grizzly

Grizzly G0584 User manual

Grizzly H8259 User manual

Grizzly

Grizzly H8259 User manual

Grizzly G1003 User manual

Grizzly

Grizzly G1003 User manual

Grizzly T10809 User manual

Grizzly

Grizzly T10809 User manual

Grizzly G0509 User manual

Grizzly

Grizzly G0509 User manual

Grizzly G9972Z User manual

Grizzly

Grizzly G9972Z User manual

Grizzly G1067Z User manual

Grizzly

Grizzly G1067Z User manual

Grizzly T25920 User manual

Grizzly

Grizzly T25920 User manual

Grizzly G0632 User manual

Grizzly

Grizzly G0632 User manual

Grizzly G0709 User manual

Grizzly

Grizzly G0709 User manual

Grizzly G4015Z User manual

Grizzly

Grizzly G4015Z User manual

Grizzly G0624 Quick start guide

Grizzly

Grizzly G0624 Quick start guide

Grizzly T28522 User manual

Grizzly

Grizzly T28522 User manual

Grizzly G5962 Instruction Manual

Grizzly

Grizzly G5962 Instruction Manual

Grizzly G0835 User manual

Grizzly

Grizzly G0835 User manual

Grizzly G0733 User manual

Grizzly

Grizzly G0733 User manual

Grizzly G0462 User manual

Grizzly

Grizzly G0462 User manual

Grizzly G8691 User manual

Grizzly

Grizzly G8691 User manual

Grizzly G0842 User manual

Grizzly

Grizzly G0842 User manual

Grizzly G0694 User manual

Grizzly

Grizzly G0694 User manual

Grizzly G8688 User manual

Grizzly

Grizzly G8688 User manual

Grizzly G0462 User manual

Grizzly

Grizzly G0462 User manual

Grizzly G1001 User manual

Grizzly

Grizzly G1001 User manual

Grizzly G0791 User manual

Grizzly

Grizzly G0791 User manual

Popular Lathe manuals by other brands

Far Tools PRO ML 550 manual

Far Tools

Far Tools PRO ML 550 manual

HOLZMANN MASCHINEN ED 400FD user manual

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN ED 400FD user manual

Sigma Far Tools One TB 100B Original manual translation

Sigma

Sigma Far Tools One TB 100B Original manual translation

Craftsman 113.228360 owner's manual

Craftsman

Craftsman 113.228360 owner's manual

Shop fox W1836 owner's manual

Shop fox

Shop fox W1836 owner's manual

Jet JML-1014I brochure

Jet

Jet JML-1014I brochure

AVL Industrial Dobby Loom user manual

AVL

AVL Industrial Dobby Loom user manual

Lodge & Shipley Model A Operator's manual

Lodge & Shipley

Lodge & Shipley Model A Operator's manual

Haussmann 5848001 manual

Haussmann

Haussmann 5848001 manual

Sharp LMV Series Operations & parts manual

Sharp

Sharp LMV Series Operations & parts manual

Woodstock M1042 owner's manual

Woodstock

Woodstock M1042 owner's manual

MiniMax C 26 GENIUS Operation and maintenance

MiniMax

MiniMax C 26 GENIUS Operation and maintenance

Milltronics SL12 Series Instruction handbook

Milltronics

Milltronics SL12 Series Instruction handbook

Jet BDB-1340A owner's manual

Jet

Jet BDB-1340A owner's manual

Smithy MI-409MZ Operator's manual

Smithy

Smithy MI-409MZ Operator's manual

Woodstock SHOP FOX W1704 owner's manual

Woodstock

Woodstock SHOP FOX W1704 owner's manual

Promac GH-1640ZX operating instructions

Promac

Promac GH-1640ZX operating instructions

King Canada CH-900C Service manual

King Canada

King Canada CH-900C Service manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.