Grundfos CIM 1 Series User manual

CIM 100-110 LON module
Installation and operating instructions
GRUNDFOS INSTRUCTIONS

2

3

Table of contents
4
CIM 100-110 LON module
English (GB)
Installation and operating instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Deutsch (DE)
Montage- und Betriebsanleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Dansk (DK)
Monterings- og driftsinstruktion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Español (ES)
Instrucciones de instalación y funcionamiento . . . . . . . . . . . . . . . . . . . . . . . . . 20
Suomi (FI)
Asennus- ja käyttöohjeet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Français (FR)
Notice d'installation et de fonctionnement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Italiano (IT)
Istruzioni di installazione e funzionamento . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Português (PT)
Instruções de instalação e funcionamento . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Русский (RU)
Паспорт, Руководство по монтажу и эксплуатации . . . . . . . . . . . . . . . . . . . 47
中文 (CN)
安装和使用说明书 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
日本語 (JP)
取扱説明書 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
한국어 (KO)
설치 및 작동 지침 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

English (GB)
5
English (GB) Installation and operating instructions
Original installation and operating instructions.
CONTENTS
Page
1. Symbols used in this document
2. Applications
The CIM 1XX LON module (CIM = Communication
Interface Module) enables data transmission
between a LON network and a Grundfos product.
The CIM 1XX is fitted in the product to be
communicated with or in a CIU 1XX unit (CIU =
Communication Interface Unit).
Retrofitting of the CIM 1XX is described in the
installation and operating instructions of the
Grundfos product.
Further information
For further information about configuration and
functionality of the CIM 1XX, see the specific
functional profile on the CD-ROM supplied with the
product.
1. Symbols used in this document 5
2. Applications 5
2.1 CIM 1XX LON module 6
3. Installation 6
3.1 Connecting the LON 6
3.2 Registration in a LON network 7
4. LEDs 7
5. Fault finding 8
6. Technical data 9
7. Service 9
7.1 Service documentation 9
8. Disposal 9
Warning
Prior to installation, read these installation
and operating instructions. Installation and
operation must comply with local
regulations and accepted codes of good
practice.
Warning
If these safety instructions are not
observed, it may result in personal injury!
Caution
If these safety instructions are not
observed, it may result in malfunction or
damage to the equipment!
Note
Notes or instructions that make the job
easier and ensure safe operation.

English (GB)
6
2.1 CIM 1XX LON module
Fig. 1 CIM 1XX LON module
3. Installation
3.1 Connecting the LON
Grundfos recommends to use a cable according to
Echelon standards.
Examples of recommended cable types
• Belden 85102
• Belden 8471
• Level IV, 22 AWG
• JY(St) Y 2 x 2 x 0.8
• TIA Category 5.
A LON network must be terminated. The termination
depends on the network topology chosen.
Fitting the cable
Procedure:
See fig. 2.
1. Connect the conductors to terminal A (pos. 1).
2. Connect the conductors to terminal B (pos. 2).
3. Connect the twisted screen ends to terminal
"Screen" (pos. 3).
Fig. 2 Connecting the LON
TM04 1956 1508
Pos. Designation Description
1 A LON terminal A
2 B LON terminal B
3 Screen LON terminal for cable
screen
4 LED1 Yellow service LED
5 Pin Service pin (push-button)
6LED2
Red/green status LED for
internal communication
between the CIM 1XX and
the Grundfos product
123465
Warning
The CIM 1XX must only be connected to
SELV or SELV-E circuits.
Note
The screen must only be connected to the
screen terminal of the CIM 1XX LON
module. See fig. 2, pos. 3.
The cable screen must never be
connected to earth via the earth clamp.
See fig. 2, pos. 4.
Note
The stripped part of the cable screen must
be as short as possible to reduce the
impedance at high frequencies.
TM04 1957 1508
Pos. Description
1 LON terminal A
2 LON terminal B
3 LON terminal for cable screen
4Earth clamp
2
3
1
4

English (GB)
7
3.2 Registration in a LON network
Grundfos products with a CIM 1XX LON module are
registered by a LON network in one of these ways:
• Service pin
• Bar code label.
Service pin
When the service pin push-button of the module is
activated, the module will send a unique 48 bit ID
code (Neuron ID) which is registered in the LON
network.
Fig. 3 Service pin
Bar code label
The Neuron ID on the module or on the enclosed bar
code label is scanned and registered in the LON
network. The bar code of the Neuron ID is in Code
128 format. The additional bar code label can be
attached to the building installation plan.
4. LEDs
The CIM 1XX LON module has two LEDs. See fig. 1.
• Yellow service LED (LED1)
• Red/green status LED (LED2) for internal
communication between the CIM 1XX and the
Grundfos product.
LED1
The yellow LED on the CIM 1XX functions as a
service LED. When the Grundfos product is
connected to the power supply, the service LED will
flash once and then remain off if the installation has
been made correctly. In case of deviations, see
section 5. Fault finding.
LED2
TM04 1958 1508
1
Status Description
Off The CIM 1XX has been switched
off.
Flashing red No internal communication between the CIM 1XX and the
Grundfos product.
Permanently
red The CIM 1XX does not support the Grundfos product connected.
Permanently
green
Internal communication between
the CIM 1XX and the Grundfos
product is OK.

English (GB)
8
5. Fault finding
Faults in a CIM 1XX LON module can be detected by observing the status of the service LED (LED1) and the
LED for internal communication (LED2). See the table below.
CIM 1XX fitted in a Grundfos product
Fault (LED status) Possible cause Remedy
1. The service LED (LED1)
remains off when the power
supply is connected.
a) The CIM 1XX has not been
fitted correctly in the Grundfos
product.
Fit the CIM 1XX correctly in the
Grundfos product.
b) No power supply to the CIM
1XX. Check the power supply to the Grundfos product.
c) The CIM 1XX is defective. Replace the CIM 1XX.
2. The service LED (LED1) is
permanently on. a) The CIM 1XX is defective. Replace the CIM 1XX.
3. The service LED (LED1)
flashes when the power
supply is connected to the
CIM 1XX, turns off, turns on
again and remains
permanently on.
a) The CIM 1XX has no
application software
(application-less).
Try to download application
software via a LON installation tool
such as LonMaker.
b) The CIM 1XX is defective. Replace the CIM 1XX.
4. The service LED (LED1)
flashes every second. a) The CIM 1XX has not been installed. Install the CIM 1XX by means of a LON installation tool such as
LonMaker.
5. The Grundfos product does
not react to changes of
settings, and the readout from
the LON network is incorrect.
The LED for internal
communication (LED2) is
permanently red.
a) The CIM 1XX does not
support the Grundfos product
connected.
Contact the nearest Grundfos
company.
b) The LON application may be
wrong, for instance CIM 110
software where CIM 100
software is required.
Download correct software via a
LON installation tool such as
LonMaker.
6. The Grundfos product does
not react to changes of
settings, and the readout from
the LON network is incorrect.
The LED for internal
communication (LED2) is
flashing red.
a) The cable between the CIM
1XX and the Grundfos product
is connected incorrectly or
damaged.
Connect the cable correctly, or
replace the cable.

English (GB)
9
CIM 1XX fitted in the CIU 1XX
6. Technical data
7. Service
7.1 Service documentation
Service documentation is available on
www.grundfos.com > International website >
WebCAPS > Service.
If you have any questions, please contact the
nearest Grundfos company or service workshop.
8. Disposal
This product or parts of it must be disposed of in an
environmentally sound way:
1. Use the public or private waste collection service.
2. If this is not possible, contact the nearest
Grundfos company or service workshop.
The crossed-out wheelie bin symbol on
a product means that it must be
disposed of separately from household
waste. When a product marked with this
symbol reaches its end of life, take it to a
collection point designated by the local
waste disposal authorities. The separate collection
and recycling of such products will help protect the
environment and human health.
Fault (LED status) Possible cause Remedy
1. The service LED (LED1)
remains off when the power
supply is connected.
a) No power supply to the CIU
1XX. Check the power supply to the CIU 1XX.
b) The CIM 1XX is defective. Replace the CIM 1XX.
2. The service LED (LED1) is
permanently on. a) The CIM 1XX is defective. Replace the CIM 1XX.
3. The service LED (LED1)
flashes when the power
supply is connected to the
CIM 1XX, turns off, turns on
again and remains
permanently on.
a) The CIM 1XX has no
application software
(application-less).
Try to download application
software via a LON installation tool
such as LonMaker.
b) The CIM 1XX is defective. Replace the CIM 1XX.
4. The service LED (LED1)
flashes every second. a) The CIM 1XX has not been installed. Install the CIM 1XX by means of a LON installation tool such as
LonMaker.
5. The Grundfos product does
not react to changes of
settings, and the readout from
the LON network is incorrect.
The LED for internal
communication (LED2) is
permanently red.
a) The CIM 1XX does not
support the Grundfos product
connected.
Contact the nearest Grundfos
company.
b) The LON application may be
wrong, for instance CIM 110
software where CIM 100
software is required.
Download correct software via a
LON installation tool such as
LonMaker.
6. The Grundfos product does
not react to changes of
settings, and the readout from
the LON network is incorrect.
The LED for internal
communication (LED2) is
flashing red.
a) The cable between the CIM
1XX and the Grundfos product
is connected incorrectly or
damaged.
Connect the cable correctly, or
replace the cable.
Note
Fault finding in a LON network requires a
special tool such as Honeywell Excelon
(not supplied by Grundfos).
Transceiver FTT 10
Cable Screened, twisted-pair, according to Echelon
standards
Transmission speed 78 kbits/s
Protocol LonTalk
Supply voltage 5 V ± 5 %
Current consumption Max. 200 mA
Storage temperature -25 °C to +70 °C
-13 °F to +158 °F

Deutsch (DE)
10
Deutsch (DE) Montage- und Betriebsanleitung
INHALTSVERZEICHNIS
Seite
1. Kennzeichnung von Hinweisen
2. Verwendungszweck
Das CIM 1XX LON Modul (CIM = Communication
Interface Module (Kommunikationsschnittstellen-
modul)) ermöglicht die Datenübertragung zwischen
einem LON-Netzwerk und einem Grundfos Produkt.
Das CIM 1XX ist in dem Produkt, mit dem die Kom-
munikation erfolgt, oder in einem CIU 1XX Gerät
(CIU = Communication Interface Unit (Kommunika-
tionsschnittstellengerät)) eingebaut.
Der nachträgliche Einbau des CIM 1XX ist in der
Montage- und Betriebsanleitung des jeweiligen
Grundfos Produkts beschrieben.
Weitere Informationen
Weitere Informationen über das Konfigurieren und
die Funktionen des CIM 1XX finden Sie in dem
speziellen Funktionsprofil, das auf der mit dem
Produkt mitgelieferten CD-ROM abgelegt ist.
1. Kennzeichnung von Hinweisen 10
2. Verwendungszweck 10
2.1 CIM 1XX LON Modul 11
3. Installation 11
3.1 Anschließen des LON 11
3.2 Anmelden in einem LON-Netzwerk 12
4. LEDs 12
5. Störungsübersicht 13
6. Technische Daten 14
7. Service 14
7.1 Serviceunterlagen 14
8. Entsorgung 14
Warnung
Diese Montage- und Betriebsanleitung ent-
hält grundlegende Hinweise, die bei der
Montage und dem Betrieb der Pumpe zu
beachten sind. Sie ist daher unbedingt vor
der Montage und Inbetriebnahme vom
Monteur sorgfältig durchzulesen. Weiter-
hin sind die bestehenden nationalen Vor-
schriften zu beachten.
Warnung
Die in dieser Montage- und Betriebs-
anleitung enthaltenen Sicherheitshin-
weise, die bei Nichtbeachtung Gefährdun-
gen für Personen hervorrufen können, sind
mit dem allgemeinen Gefahrensymbol
"Sicherheitszeichen nach DIN 4844-W00"
besonders gekennzeichnet.
Achtung
Dieses Symbol finden Sie bei Sicherheits-
hinweisen, deren Nichtbeachtung Gefah-
ren für die Maschine und deren Funktionen
hervorrufen kann.
Hinweis
Hier stehen Ratschläge oder Hinweise, die
das Arbeiten erleichtern und für einen
sicheren Betrieb sorgen.