Grundig DSR 4530 HDD User manual

ǵ
PERSONAL
DIGITAL
SATELLITE
RECORDER
DSR 4530 HDD
DEUTSCH
ENGLISH

2
CONTENTS____________________________________________
4 General information
4 Scope of delivery
4 Receiving digital satellite channels
4 Recording digital satellite channels
5 Special features of your digital recorder
6 Set-up and safety
7-10 Overview
7 The front of the digital recorder
8 The back of the digital recorder
9-10 The remote control
11-12 Connection and preparation
11 Connecting the satellite antenna
11 Connecting the television
11 Connecting a DVD recorder/video recorder
12 Connecting an AV receiver or hi-fi system
12 Connecting a digital multi-channel amplifier
12 Connecting the power cord
12 Putting batteries in the remote control
13-22 Settings
13 The menu
14 Assigning presets
15 Editing the channel list
16 Editing favourites lists
17 Setting the local time
18-19 Adjusting the digital receiver to the television set
20 Adjusting the digital receiver to the LNB configuration of the satellite antenna
21 Audio settings
22 PVR settings
23-24 Basic functions
23 Switching on and off
23 Mode selection
23 Selecting presets
23 Displaying channel information
24 Adjusting the volume
24 Muting the sound
24 Selecting stations from lists
24 Switching from the current station to the previous one
25-26 Time shift functions
25 Time shift – watching a current television programme with a delay
26 Pausing a live programme
26 Searching for scenes in the time shift memory

ENGLISH
3
CONTENTS____________________________________________
27 TV guide
27 The electronic TV guide
28-30 Timer recordings in the archive
28 Programming recordings – by adopting the data from the TV guide
29 Programming recordings – by entering the data for the television or radio
programme
30 Deleting a timer
30 Entering the switch-off time
31 Recording in the archive
31 Preparing a recording
31 Recording a television or radio programme manually
32-33 Archive playback
32 Preparation
32 The archive
32-33 Playback
34 Deleting programmes in the archive
35-36 Teletext mode
35 Teletext
35-36 Additional functions
37-40 Additional functions
37 Subtitles
38 Setting the menu language
38 Deleting channel or favourites lists
39 Preprogrammed satellite channels
39 Automatic station search
40 Manual station search
41-42 Special settings
41 Resetting the receiver to the original state
41 Updating the digital receiver software
42 Formatting the hard drive
42 Selecting the remote control level
43-46 Information
43 Displaying station reception parameters
43 Displaying hard drive information
44 Displaying device information
44 Connecting the digital receiver to a PC
45 Technical data
45 Environmental note
46 Troubleshooting

4
Scope of delivery
1Digital Satellite Receiver DSR 4530 HDD
2Tele Pilot 767 PVR remote control
32 batteries for the remote control (2 x 1.5 V, AA type batteries)
4SCART cable
5Power cord
6Operating manual
Receiving digital satellite channels
In order to use your new DSR 4530 HDD digital recorder you need
a digital-compatible satellite antenna, which must be installed and
aligned to the satellites (for example Astra and EutelSat/Hotbird).
Unlike broadcasts of analog satellite channels not every digital TV
or radio station is assigned to one transmission frequency, but
several TV and/or radio stations are broadcast on one transponder.
To help you with the choice and settings for satellite channels, a
selection of TV and radio stations have already been programmed
for this device. You can start a channel search to ensure that any
new satellite channels are available on your device.
How this works and what you need to remember can be found on
page 39 of this operating manual.
Of course, you can easily program new satellite channels. You can
find the latest transponder information on the teletext pages of
various broadcasters, in a current satellite TV magazine or on the
Internet.
Recording digital satellite channels
Television programmes can be recorded on the integrated
hard drive of the digital recorder.
Using the time shift function you can watch television programmes
with a time shift which are stored in the time shift memory. You can
stop these programmes and continue playback at the same point.
GENERAL INFORMATION__________________

ENGLISH
5
Special features of your digital recorder
The DSR 4530 HDD digital receiver can receive and process all
unencrypted digital channels.
This digital receiver has a built-in digital receiver unit for satellite
channels. The receiver unit converts the signals from digital satellite
channels to provide outstanding audio and picture quality.
Television programmes can be recorded on the integrated hard
drive of the digital recorder.
So that your new digital receiver always works with the latest pro-
gram data and operating software, it is first necessary to conduct
an update.
Using the Astra 19.2° East satellite, you can update the digital
recorder’s software.
How this works and what you need to remember can be found on
page 41 of this operating manual.
The TV guide tells you of any schedule changes at short notice, and
also provides an overview of all the channels’ schedules for the next
few hours.
Detailed information on individual television programmes is avail-
able at the touch of a button.
This digital receiver has a very comprehensive, user-friendly menu
system.
The menu is displayed on the television screen, and the functions of
the remote control buttons are explained.
GENERAL INFORMATION__________________

6
SET-UP AND SAFETY___________________________
°C2h
°C
ǵ
ON/OFF
DSR4530 HDD
ǵ
ON/OFF
DSR4530 HDD
ǵ
ON/OFF
DSR4530 HDD
Krieg im Balkan
ǵ
ON/OFF
DSR4530 HDD
EURO AV1 TV
EURO AV2 VCR RS 232
This digital receiver is designed to receive, record and play back video
and audio signals. Any other use is expressly prohibited.
When setting up the digital receiver, make sure it is in a horizontal posi-
tion and that the mains socket is easily accessible.
When setting up the digital recorder, remember that furniture is often
coated with various types of varnish and plastic, which often contain
chemical additives. These additives may cause corrosion to the feet of
the unit. This may leave stains on the surface of the furniture which can
be difficult or impossible to remove.
If the digital receiver is subject to a sudden change in temperature, for
example when brought in from the cold to a warm room, let it stand for
at least two hours before you connect it to the mains supply.
Do not expose the digital receiver to moisture of any kind.
The digital receiver is designed for use in dry rooms. If you do use it out-
doors, make sure it is protected from moisture such as rain or splashing
water. Do not place any vessels such as vases on the digital receiver.
These may be knocked over and spill fluid on the electrical components,
thus presenting a safety risk.
Do not place the digital receiver close to heating units or in direct sun-
light, as this will impair cooling. Maximum ambient temperature +5 °C
to +40 °C.
Place the digital receiver on a hard, level surface. Do not lay any objects
such as magazines on the digital receiver. When placed in a cabinet,
make sure there is a minimum space of 10 cm around it.
Thunderstorms are a danger to all electrical devices. Even if the digital
receiver is switched off, it can be damaged by a lightning strike to the
mains or the antenna.
Always disconnect the mains and antenna plugs during a storm.
Never open the digital receiver casing under any circumstances.
Warranty claims are excluded for damage resulting from improper
handling.
Note:
Do not connect any other equipment while the device is switched on.
Switch off the other devices as well before connecting them.
Do not plug in the power cord of your device until you have connected
the external equipment and the antenna.

ENGLISH
7
The front of the digital recorder
ON/OFF ǼSwitches the digital receiver on and off.
•(red) The digital receiver is in standby mode.
In the display
TV Lights up in TV mode.
RADIO Lights up in radio mode.
SUB Lights up when subtitles are available.
REC Lights up during timer recordings.
! Lights up during playback/pause.
8Lights up during playback.
iOpens and closes the main menu.
P+, P- Switches up and down through the presets.
In the menus: moves the cursor up/down, selects and
changes individual entries.
Ǹ, ǷAdjust the volume.
In the menus: move the cursor left/right,
selects and change individual entries.
OK Opens the channel list.
In the menus: confirms entries.
OVERVIEW____________________________________________
ǵ
ON/OFF
DSR 4530 HDD

8
OVERVIEW____________________________________________
The back of the digital recorder
INPUT SAT Antenna socket for the satellite antenna.
AUDIO OUT Stereo output sockets (left/right) (RCA) for the
L R hi-fi system.
VIDEO OUT Video signal output socket (FBAS) for the television
or AV receiver.
DIGITAL Audio outputs for digital audio signal (RCA,
AUDIO OUT optical) for digital multi-channel amplifier.
EURO AV 2 ɮVCR SCART socket (input and output) for the video
recorder.
EURO AV 1 ɮTV SCART (output) socket for the television.
RS 232 Serial interface for connecting to a PC for software
updates.
220-240V
~ Connection socket for the power cord supplied.
50/60 Hz 20 W
Note:
The model designation can be found on the back
of the digital recorder.
Caution:
Do not connect any other equipment while the
device is switched on. Switch off the other devices
as well before connecting them.
Do not plug in the power cord of your device until
you have connected the external equipment and
the antenna.
EURO AV 1 TV
EURO AV 2 VCR RS 232

ENGLISH
9
OVERVIEW____________________________________________
The remote control
ǼSwitches the digital receiver to standby, and from
standby to the channel last selected.
FOpens the »Audio settings« menu.
yOpens the »Subtitles« menu.
?Displays programme information.
1 … 0 Select stations.
dSwitches the sound to mute and on again.
iOpens and closes the main menu.
ZSwitches between the two most recently selected
channels.
P+ P- Switch channels up and down one by one.
ǸǷ Adjust the volume.
OK Opens the channel list.
TXT Switches from TV mode to teletext mode, and back to
TV mode.
TV-G Opens the electronic TV guide.
TV/ RADIO Switches between and TV and radio modes.
%Switches to forwards slow motion at various speeds
during playback.
!Freeze frame/pause.
Advances the picture frame by frame.
7
A/B Ends playback.
Switches between the channel list and favourites list in
the »Edit favourites list« menu.
8Switches to HDD archive.
Starts playback
Tele Pilot 767 PVR
DR DVD
TV
z
TXT
TV-G
d
TV/Radio A/B

10
5Starts recording and enters the switch-off time
(in 5 minute steps).
“Rewinds” the programme in 5 minute steps during
playback.
Ȅ6Opens the »Timer recorder« menu.
“Fast forwards” the programme in 5 minute steps
during playback.
ľľ ıı
Switch to forwards or reverse picture search at various
speeds during playback.
DR, TV Switches to operating a second GRUNDIG
DVD digital recorder, GRUNDIG television or GRUNDIG
DVD player.
Keep the appropriate button (»DR«, »TV«, »DVD«)
pressed down. Then press the button.
Note:
The functions available depend on the model of the
device you are using.
Just try it out.
OVERVIEW____________________________________________
Tele Pilot 767 PVR
DR DVD
TV
z
TXT
TV-G
d
TV/Radio A/B

ENGLISH
11
Connecting the satellite antenna
1Connect the antenna cable of the satellite antenna to the »INPUT SAT«
socket on the digital recorder (screw connector, F connector).
Connecting the television
1Plug the supplied SCART cable into the »EURO AV1 ɮTV« socket of
the digital recorder and the corresponding SCART socket of the tele-
vision.
Connecting a DVD recorder/video recorder
1Plug a standard SCART cable into the »EURO AV2 ɮVCR« socket of
the digital recorder and the corresponding SCART socket of the DVD
recorder/video recorder (e.g. EURO AV, LINE IN/OUT, EXT.1).
Note:
When playing back a video recording, the video and audio signal from
the DVD/recorder/video recorder is automatically looped through to
the television via the »EURO AV1 ɮTV« socket on the digital
recorder.
The digital receiver may not be switched off with the main power button.
CONNECTION AND PREPARATION
7
12
EURO AV 1 TV
EURO AV 2 VCR
EURO AV 1 TV
EURO AV 2 VCR
EURO AV 1 TV
EURO AV 2 VCR RS 232
R
L
AV1
AV2
ń
R
L
AUDIO
R
L
I
N
O
U
T
DEC. - AV 2
EURO - AV 1
SAT

12
Connecting an AV receiver or hi-fi system
1Plug a standard RCA cable into the »VIDEO OUT«and »AUDIO
OUT L R«sockets (left/right) on the digital recorder and the corre-
sponding inputs on the AV receiver or hi-fi system.
Connecting a digital multi-channel amplifier
1Plug a standard RCA cable into the »DIGITAL AUDIO OUT«socket
on the digital recorder and the corresponding socket on the digital
multi-channel amplifier
or
plug a standard optical digital cable into the »DIGITAL AUDIO
OUT«socket on the digital recorder and the corresponding socket on
the digital multi-channel amplifier.
Connecting the power cord
1Plug the power cord supplied into the »220-240V~ 50/60Hz«
socket on the digital recorder.
2Plug the power cord into the wall socket.
Note:
Do not plug in the power cord of your device until you have connected
the external equipment and the antenna.
Putting batteries in the remote control
1Open the battery compartment by removing the lid.
2Put in the batteries (AA, 2 x 1.5 V).
Make sure the polarity is correct (as shown on the base of the battery
compartment).
3Close the battery compartment.
Note:
If the digital receiver no longer reacts properly to remote control com-
mands, the batteries may be flat. Always remove used batteries.
The manufacturer accepts no liability for damage caused by leaking
batteries.
Environmental note
Batteries, including those which contain no heavy metal, should not be
disposed of with household waste. Please dispose of used batteries in an
environmentally sound manner. Find out about the legal regulations
which apply in your area.
CONNECTION AND PREPARATION
EURO AV 1 TV
EURO AV 2 VCR
R
EURO AV 1 TV
EURO AV 2 VCR
EURO AV 1 TV
EURO AV 2 VCR

ENGLISH
13
The menu
This digital receiver has a very comprehensive, user-friendly menu
system. The menu is displayed on the television screen.
The digital receiver responds to many functions which you select on
the remote control with informative menus and icons on the tele-
vision screen.
It enables you to select many different settings and it contains infor-
mation on using your digital recorder.
The »Main Menu«contains the most important controls for your dig-
ital recorder. Its menu system controls the dialogue between you
and the digital receiver.
Press »i«to open the »Main Menu«.
You can navigate in the menu by pressing »P-«or »P+«and select
the item you want. The selected item is highlighted.
When you press »OK«to confirm your selection, a sub-menu
appears.
You can also navigate here by pressing »P-«or »P+«and select
the item you want. The selected item is highlighted.
Press »OK«to confirm.
Another menu usually appears, where you can use »P-«or »P+«to
navigate and make the setting.
Make settings using »P-«, »P+«, »Ǹ«, »Ƿ«or »1...0«.
Press »Z«to quit the current menu level.
Exit the settings and the menu with »i«.
SETTINGS ______________________________________________
Main Menu
Select Back Exit
and open
Settings
Channel lists
Program information
Timer
Installation
ǵ

14
Assigning presets
The digital receiver is already preprogrammed with the following
satellites: Astra 19.2°East, Eutelsat/Hot Bird 13°East, Turksat 1C,
Sirius 2/3, Amos and Hellas Sat 2.
The following settings allow you to select the menu language, the
country where you are operating the digital receiver and the main
satellites.
Channels selected from the main satellites are transferred to the
favourites list. You can then sort the stations in the order you
require.
1Switch on the digital receiver by pressing »Ǽ«on the receiver.
–The »Sprache«(Language) menu appears when the device is
first switched on.
2Select your language using »P-«or »P+«and press »OK«to
confirm.
–The »Country«menu appears.
3Select the country with »P-«or »P+«and press »OK«to con-
firm.
–The »Satellite«menu appears.
4Select main satellites with »P-«or »P+«and press »OK«to
confirm.
–The channels are entered in the channel list.
–The channels of the other satellites are added to the channel
list after you set the main satellite.
–After transferring the channels the recorder switches to
Preset 1.
–You can change the order of the presets as required and
delete channels you do not need (see the section on editing
the channel list on page 15).
Note:
The world of digital radio and television channels changes
rapidly. So that all new satellite channels are available on your
device you should start an automatic channel search regularly.
See corresponding chapter on page 39.
SETTINGS ______________________________________________
Sprache
Auswählen
und bestätigen
Deutsch Español
English Suomi
Svenska
Polski
Français
Italiano
Country
Select Back
and confirm
Germany Switzerland
Austria Poland
Spain
Italy
Satellite
Select Back
and confirm
Astra 19.2
Hot Bird
Turksat 1C
Hellas Sat 2
Sirius 2/3
Amos 1
ǵ

ENGLISH
15
SETTINGS ______________________________________________
Editing the channel list
You can change the order of presets as required and delete stations
you do not need.
1In the »Main Menu«, select »Channel lists«with »P+«or
»P-«and confirm with »OK«.
2Confirm the selection of »Channel list«with »OK«.
–The channel list appears.
Deleting stations
1Select the station to be deleted with »P-«or »P+«and press
»OK«to confirm.
–The station is highlighted in orange.
2Select another station with »P-«or »P+«and confirm with
»OK«.
3Press »«to delete the stations.
–The highlighted stations are deleted.
Moving stations
1Select the station to be moved with »P-«or »P+«and press
»OK«to confirm.
–The station is highlighted in orange.
2Select another station with »P-«or »P+«and confirm with
»OK«.
3Select the channel before which the highlighted stations are to
be inserted with »P-«or »P+«.
4Press »«(yellow) to move the stations.
Ending the settings
1Press »i«and then »OK«to save the settings.
Note:
If you do not wish to save the changes, press »Ǹ«or »Ƿ«to
select »No«and confirm with »OK«.
Edit Channel Lists
Select Back Exit
and open
Channel list
Favorites 1
Favorites 2
Favorites 3
Favorites 4
Edit Channel List
Astra 19.2
1 Sat 1
2 ProSieben
3 KABEL1
4 NEUN LIVE Telev
5 DSF
6 HSE24
7SAT.1
8 N24
9 TELE 5
10 Das Erste
Select Back Exit
and mark Delete Move
Edit Channel List
Astra 19.2
1 Sat 1
2 ProSieben
3 KABEL1
4 NEUN LIVE Telev
5 DSF
6 HSE24
7SAT.1
8 N24
9 TELE 5
10 Das Erste
Select Back Exit
and mark Delete Move
Save
Yes No

16
Editing favourites lists
You can change the order of presets as required and delete stations
you do not need.
You can select your favourite stations and save them in up to four
lists.
1In the »Main Menu«, select »Channel lists«with »P+«or
»P-«and confirm with »OK«.
2Select »Favorites list 1«, »Favorites list 2«, »Favorites list 3«or
»Favorites list 4«with »P+«or »P-«and confirm with »OK«.
–The »Edit favorites list«page appears.
3Select the station to be moved with »P-«or »P+«and press
»OK«to confirm.
–The station is highlighted in orange.
4Select other stations with »P-«or »P+«and confirm with
»OK«.
5To move the channels in the favourites list, press »A/B«and
confirm with »OK«or »«.
–You can switch between the channel list and your favourites
by pressing »A/B«.
–You can store up to 100 stations in the favourites list.
–You can change the sequence of the stations or delete stations
which are not required (see the chapter on editing the chan-
nel list).
Note:
If a station is deleted from the channel list, it is also removed
from the favourites list.
6Press »i«and then »OK«to save the settings.
Note:
If you do not wish to save the changes, press »Ǹ«or »Ƿ«to
select »No«and confirm with »OK«.
SETTINGS ______________________________________________
Edit Favorites
Select Back Exit
and mark A<->B Add
Delete
A: Channel list
1 Sat 1
2 ProSieben
3 KABEL1
4 NEUN LIVE Telev
5 DSF
6 HSE24
7SAT.1
8 N24
9 TELE 5
B: Favorites 1
1 Sat 1
A/B
Edit Channel Lists
Select Back Exit
and open
Channel list
Favorites 1
Favorites 2
Favorites 3
Favorites 4

ENGLISH
17
Setting the local time
To ensure that the TV guide always shows the current programmes
at the right time, enter the difference between your local time and
GMT (Greenwich Mean Time at longitude “0”).
All times given by the TV guide are then converted to your local
time.
1In the »Main Menu«, select »Installation«with »P-«or »P+«
and press »OK«to confirm.
2Select »Time«with »P-«or »P+«and press »OK«to confirm.
3Confirm the selection of »Time zone«with »OK«and then
change the time difference in 30-minute increments with »P-«
or »P+«.
Note:
For Germany: + 1.00 hour
4Select »Daylight saving time«with »P-«or »P+«and press
»OK«to confirm.
5Press »P-«or »P+«to select »Off«(winter time) or »On«
(summer time).
If you select »Automatic«and then switch to a channel on the
Astra satellite, the time is switched automatically.
6Confirm your settings by pressing »OK«.
7Press »i«and then »OK«to save the settings.
SETTINGS ______________________________________________
Installation
Select Back Exit
and open
Menu language
Channel search
Video output
Time
Antenna connection
Special functions
Info
Time
Select Back Exit
and open
Current time 08:05 h
+1.00 h
On
Time zone
Daylight saving time

18
Adjusting the digital receiver to the television set
Specifying the video signal at the Euro AV (TV)
output
You can choose between the settings »FBAS«(normal picture
quality), »RGB«(high picture quality) »Y/C«(S-Video signal) and
»YUV«(component signal). The default setting is »RGB«.
1In the »Main Menu«, select »Installation«with »P-«or »P+«
and press »OK«to confirm.
2Select »Video output«with »P-«or »P+«and press »OK«to
confirm.
3Confirm the selection of »Signal type«with »OK«.
4Press »P-«or »P+«to select the setting and press »OK«to
confirm.
5Press »i«and then »OK«to save the settings.
Selecting the television picture format
If you have a 4:3 format television or flat screen, select the »4:3«
setting.
If you have a 16:9 format television or flat screen, select the »16:9«
setting.
1In the »Main Menu«, select »Installation«with »P-«or »P+«
and press »OK«to confirm.
2Select »Video output«with »P-«or »P+«and press »OK«to
confirm.
3Select »TV format«with »P-«or »P+«and then press »OK«.
4Press »P-«or »P+«to select the video format, and then press
»OK«to confirm.
Note:
If picture format 4:3 is selected, you can also select picture
conversion.
5Press »i«and then »OK«to save the settings.
SETTINGS ______________________________________________
Video output
Select Back Exit
and open
TV format
Signal type RGB
4:3
Letterbox
❙
■■■■■■■ ■
❙
Picture conversion
OSD Transparency
Video output
Select Back
and confirm
RGB
16:9
❙
■■■■■■■■
❙
Signal type 4:3
16:9
TV format
Picture conversion
OSD Transparency
Installation
Select Back Exit
and open
Menu language
Channel search
Video output
Time
Antenna connection
Special functions
Info

ENGLISH
19
Selecting picture conversion for the television
If you have a 4:3 format television or flat screen, the following
settings are available:
»Pan&Scan«for wide-screen playback without black bars on the
top and bottom edges of the screen.
»Letterbox«for wide-screen playback with black bars on the top
and bottom edges of the screen.
1In the »Main Menu«, select »Installation«with »P-«or »P+«
and press »OK«to confirm.
2Select »Video output«with »P-«or »P+«and press »OK«to
confirm.
3Select »Picture conversion«with »P-«or »P+«and then press
»OK«.
4Press »P-«or »P+«to select the picture conversion and press
»OK«to confirm.
5Press »i«and then »OK«to save the settings.
Selecting the transparency of the OSD
You can adjust the transparency of the OSD menu.
1In the »Main Menu«, select »Installation«with »P-«or »P+«
and press »OK«to confirm.
2Select »Video output«with »P-«or »P+«and press »OK«to
confirm.
3Select »OSD Transparency«with »P-«or »P+«and then press
»OK«.
4Press »Ǹ«or »Ƿ«to select the transparency and press »OK«
to confirm.
5Press »i«and then »OK«to save the settings.
SETTINGS ______________________________________________
Video output
Select Back
and confirm
RGB
4:3
❙
■■
■■❙
■■■■■■ ❙
Signal type
Letterbox
Pan&Scan
TV format
Picture conversion
OSD Transparency
Video output
Modify Back
and confirm
TV format
Signal type
Picture conversion
RGB
16:9
Letterbox
❙ ■■
■■❙
■■■■■■ ❙
OSD Transparency

20
Adjusting the digital receiver to the LNB
configuration of the satellite antenna
The digital receiver has been factory set so that it is ready for oper-
ation, without time-consuming adjustment, with most satellite anten-
nas and LNB configurations.
Changes in this menu have a direct effect on the reception charac-
teristics of the digital recorder and therefore should only be made
by an expert.
1In the »Main Menu«, select »Installation«with »P-«or »P+«
and press »OK«to confirm.
2Select »Antenna connection«with »P-«or »P+«and press
»OK«to confirm.
3Select the item with »P-«or »P+«and make the setting with
»Ǹ«, »Ƿ«or »1 ... 0«:
–»LNB«: For selecting the satellites.
–»LNB supply«: For switching the LNB power supply on
and off.
–»Low band«: To set the oscillator frequency for low
band, select this line and confirm with
»OK«. Enter the value with »1 ... 0«.
–»High band«: To set the oscillator frequency for high
band, select this line and confirm with
»OK«. Enter the value with »1 ... 0«.
–»DiSEqC«: If you want to receive up to four satel-
lites simultaneously, each LNB must be
assigned to its input on the DiSEqC
switch.
–»Tone burst«: If you want to receive two satellites at
the same time, each LNB is assigned to
its input on the tone burst switch.
4Press »i«and then »OK«to save the settings.
SETTINGS ______________________________________________
Antenna connection
Select Back Exit
and open
LNB
LNB supply
Low band
High band
DiSEqC
Tone burst
Astra 19.2
Ein
9.750 GHz
10.600 GHz
A
A
Installation
Select Back Exit
and open
Menu language
Channel search
Video output
Time
Antenna connection
Special functions
Info