GST C-9103 User manual

30305302 Issue 3.02
Features
Twin LED for 360°view.
Built-in microprocessor selects and processes
data in real time.
Rate of rise and fixed temperature alarm modes.
Remote indicator output available.
Designed to comply with EN 54-5 standard.
Description
C-9103(Ex) Explosion Proof Rate of Rise and Fixed
Temperature Heat Detector is non-addressable.
Built-in microprocessor, it works stably with reliable
fixed fire judging program, applicable to Zone I and
Zone II in petrol and chemistry industries. Used
together with I-9332 interface, it can be connected
with compatible FACP (fire alarm control panel) to
process fire alarm signals. When checking the fire
signal, the detector transmits it to the interface by
changing its own current and shows fire alarm
condition by lighting indicator until it’s reset.
Connection and Cabling
Fig.1 shows the detector bottom and Fig. 2 the base.
100mm
C
D
Ex
03
-
Z
45mm~75mm
5mm
Mounting
Hole
Fig. 1 Fig. 2
There are four terminals with numbers on the base.
1: Detection zone positive IN
2: Detection zone positive OUT
3. Detection zone negative IN and OUT
2: Positive terminal of remote indicator
4: Negative terminal of remote indicator
Recommended Cabling
1.0mm2 or above fire cable, the capacitance
distributed among cables should not be over 0.04μF,
and the inductance distributed should not be over
4.3mH. Subject to local codes.
Installation
A fixed installation direction is ensured by the location
elements on the detector and the base. Fix the base
with two tapping screws, and then align mark C on the
detector with Aon the base, rotate the detector to align
mark C with mark B (Refer to Fig. 1 and 2 for the
position of the marks), the detector will be fitted to the
base.
Fig. 3 shows the installation of the detector.
Note: The detector shall be horizontally installed. If
it has to be installed on an inclined plane, the
inclination angle shall not be over 45º.
Conduit
Detector
Base
Back Box
Fig. 3
Application
Warning: The detector should be connected with
fire alarm control panel or other devices with
current limit function. Otherwise the detector may
be damaged by too heavy alarm current.
The intrinsically safe fire system is made up of C-9103
(Ex) detector, FACP, I-9332 Interface, C-9101(Ex)
Explosion Proof Combination Heat/Photoelectric
Smoke Detector, C-9201 (Ex) Manual call point and
4.7kΩ end-of-line resistor. Fig. 4 shows the system
connection.
Remote Indicator Remote Indicator Detector
Detector
4
3
2
1
Z1
Z2
O+
O-
D2
D1
Safe Area
I-9332 Interface
Hazardous Area
I2
I1
O2 O1
K1 K2
Manual Call Point
4.7kΩEnd-of-line Resistor
Detector
Remote Indicator
Fig. 4
NOTES:
1. The interface can connect up to 10 explosion
proof products.
2. During maintenance, products passing the
explosion-proof test should not be replaced and
parts and structure affecting explosion-proof
functions should not be modified.
C-9103(Ex)
Explosion Proof Rate of Rise and
Fixed Temperature Heat Detector

30305302 Issue 3.02
Maintenance
1. The detector should be installed just before
commission and kept well before installation, taken
corresponding measures for dust-proof, damp-proof
and corrosion-proof.
2. The dust cover should not be removed until the
project has been plunged into usage.
3. Fire simulation test should be done to the
detector at least every 6 months.
Specification
Operating Voltage
24VDC(12VDC~28VDC)
Standby Current
≤60μA
Alarm Current
10mA≤I≤30mA
Indicators
Red. Quiet in normal
condition. Illuminates steadily
in alarm.
Ex Marking
ExibIICT6
Remote Indication
output
Directly connecting with
remote indicator (built-in
2kΩresistor in series). Quiet
in normal condition.
Illuminates steadily in alarm.
Maximum Ripple
Voltage
4V (peak-to-peak value)
Alarm Clear
Instantaneous Power-off (5s
Max., 2.5VDC Max.)
Power-up Time
≤10s
Action
Temperature
58℃
Detector Type
A1R
Wiring
Polarized 2-core for detection
zone cable.
Polarized 2-core for remote
indicator.
Zener barrier
parameter
U0＝28V, I0＝93mA
Ingress Protection
Rating
IP33
Ambient
Temperature
-10℃～+50℃
Relative Humidity
≤95%, non condensing
Material and Color
of Enclosure
ABS (Surface resistance
≤109Ω), white (RAL 9016)
Dimension
Diameter: 100mm
High: 58mm (with base)
Mounting Hole
Distance
45mm～75mm
Weight
About 120g
Tools and Accessories
Model
Name
Remark
I-9332
Interface
Order Separately
DZ-03(Ex)
Base
Order Separately
Limited Warranty
GST warrants that the product will be free of charge
for repairing or replacing from defects in design,
materials and workmanship during the warranty period.
This warranty does not cover any product that is found
to have been improperly installed or used in any way
not in accordance with the instructions supplied with
the product. Anybody, including the agents,
distributors or employees, is not in the position to
amend the contents of this warranty. Please contact
your local distributor for products not covered by this
warranty.
This Data Sheet is subject to change without notice. Please contact GST for more information or questions.
Gulf Security Technology Co., Ltd.
No. 80, Changjiang East Road, QETDZ, Qinhuangdao, Hebei, P. R. China 066004
Tel: [phone] Fax: [phone]
[e-mail] www.gst.com.cn