GWINNER CALEA User manual

1GENERAL CALEA ASSEMBLY INSTRUCTIONS
GENERAL INSTALLATION
CALEA
Qualied specialist personnel
IMAGE 1 Example walls CE57 and CE217
IMAGE 2, Fitting the anti-tip mechanism
On all 5-8-increment U cabinets, a
fixing bracket with metal pins is fitted
as an countersunk screw and an
8-mm-dia. plastic wall plug is used to
do so. The 13-mm cover panel only co-
vers the fittings on angled assemblies.
+/-
Push the levelling gliders
into the intended holes
and align the cabinets
Wall plug,
dia. 8 mm
4x17 fillisterhead
screw
5.5x70
cylinderhead screw
PLEASE NOTE!
CAUTION! Follow the specications carefully when tting wall units. Secure all
elements that may tip with the anti-tip mechanisms supplied.

2GENERAL CALEA ASSEMBLY INSTRUCTIONS
IMAGE 3, Joining cabinets, tting cover panels
Secure the 13 mm cover
panels at the marked
points from the inside.
(4x27mm countersunk
screw and cover caps in
the carcase colour)
M4x28 connecting screw
with sleeve nut
Storage compartment for
cables, transformer, etc.
IMAGE 4, Joining and securing base elements
2
3
1
4
+/-
Connecting base elements with
8x countersunk screws M8x 25 mm black
Securing the base
with 12x countersunk
screws Ø5x 80 mm
4x adjusting screws
M8x 25 mm for
height adjustment.
Adhere 4x 3 mm felt strips
AF4

3GENERAL CALEA ASSEMBLY INSTRUCTIONS
IMAGE 5, Fitting cover panels and lighting
"
2
1
3
Secure the 13 mm cover panels
at the marked points from the
inside.
(4x27 mm countersunk screw and
cover caps in the carcase colour)
If requested by the customer,
adhere the LED lighting (self-
adhesive); cut to size if necessary,
e.g. 1150 or 1450 mm and t a
strain relief on both sides using
Liko 3x13 mm.
Cut the LED strip
e.g. 1150 mm for
1226 mm wall unit
„LN120“ lighting with 115 cm
below 123 cm wall unit
Secure the cable using a cable
clip and lay the lighting cables
in the carcase.
Cover cap,
d = 12 mm

4GENERAL CALEA ASSEMBLY INSTRUCTIONS
IMAGE 6, Drilling the wall panel and wall unit
IMAGE 7, Hanging the wall unit
5.5x70 cylinder-head screw
and 8-mm wall plug
3x 125 mm rails per
cabinet
Drill three 8-mm wall plugs
and screw in the wall hook
The wall plugs supplied are suitable for the following sub-surfaces:
Concrete, solid brick, ventilating brick, hollow concrete blocks.
If there is a different subsurface, select an appropriate fixing material.
Hanging the
wall unit
Adjusting the
wall units–
Caution! Check
from above that all
ttings have been
tted in the rails.
Upper adjustment screw
= depth adjustment
Lower adjustment screw
= height adjustment

+/-
+/-
+/-
+/-
+/-
+/-
+/-
+/-
+/-
+/-
+/-
+/-
+/-
+/-
+/-
+/-
5GENERAL CALEA ASSEMBLY INSTRUCTIONS
IMAGE 8, Hanging the wall panel
2
3
1
Adjusting
wall panels
Hang wall panel
Set the wall panel
angle using the AF8
spanner wrench
+/-
IMAGE 9, Fitting cover panels and feet
M4x28 connecting screw
with sleeve nut
Secure the 13-mm cover panels
at the marked points from the inside.
(4x27mm countersunk screw and
cover caps in the carcase colour)
Push the levelling gliders into the intended holes
and align the cabinets

6GENERAL CALEA ASSEMBLY INSTRUCTIONS
2
1
3
Secure the 13-mm cover panels at the
marked points from the inside.
(4x27mm countersunk screw and
cover caps in the carcase colour)
Secure the cable using a cable
clip and lay the lighting cables
in the carcase.
Detailed view from behind with LED
Rear view with LED
Hängeschrank 1 Raster
IMAGE 10, Fitting cover panels and lighting
„LEDSET4“ lighting
If requested by the customer,
adhere 4-sided LED proles,
above + below L=2112 mm
side profiles L=171 mm
(Q-Line Mini Opal)
Interior cable outlet
6-way distributor,
lower cover panel
with cut-out for cable

5.5x70 cylinder-head screw
and 8-mm wall plug
The wall plugs supplied are suitable for the following sub-surfaces:
Concrete, solid brick, ventilating brick, hollow concrete blocks.
If there is a different subsurface, select an appropriate fixing material.
7GENERAL CALEA ASSEMBLY INSTRUCTIONS
IMAGE 11, Drilling the CE217 combination
3x distance spacers
75 x 75 x 8 mm
For H1 cabinet
with lighting 5.5x70 cylinder-head
screw and 8-mm wall
plug + wall rails
WP5L/WP5R
Wood drill Ø8 mm
IMAGE 12, Hanging the cabinets
Upper adjustment screw
= depth adjustment
Lower adjustment screw
= height adjustment
Adjusting the wall units
Tighten the screw no. 3,
safety catch.

+/- Push the levelling gliders into the
intended holes and align the cabinets
IMAGE 13, Aligning the lower cover panel
IMAGE 14
IMAGE 15, Securing the anti-tip mechanism
Secure the 26-mm cover panels at
the marked points from the inside.
(4x27mm countersunk screw and cover
caps in the carcase colour)
Fit nickel-plated cover caps
(dia. 5 mm) over the unused
connecting holes in the
cabinet sides.
M4x28 connecting screw
with sleeve nut
On all 5-8-increment U cabinets, a
fixing bracket with metal pins is fitted
as an anti-tip mechanism. A 5x60 mm
countersunk screw and an 8-mm-dia.
plastic wall plug is used to do so. The
13-mm cover panel only covers the
fittings on angled assemblies.
8GENERAL CALEA ASSEMBLY INSTRUCTIONS

The wall plugs supplied are suitable for the following sub-surfaces:
Concrete, solid brick, ventilating brick, hollow concrete blocks.
If there is a different subsurface, select an appropriate fixing material.
9GENERAL CALEA ASSEMBLY INSTRUCTIONS
IMAGE 16A, Example of CE1 with WRA1-L
IMAGE 16B, Drilling the wall panel
Drill the 8-mm wall plug and
screw in the wall hook
6 x wooden
dowels dia. 8x50
Hexagon spanner AF4
9x Unita connecting screws
Diameter 7x70 mm
2
1

IMAGE 17, Drilling the wall units
10 GENERAL CALEA ASSEMBLY INSTRUCTIONS
The wall plugs supplied are suitable for the following sub-surfaces:
Concrete, solid brick, ventilating brick, hollow concrete blocks.
If there is a different subsurface, select an appropriate fixing material.
5.5x70 cylinder-head screw
and 8-mm wall plug
Zylinderkopfschraube
5,5x70 + Dübel 8 mm
IMAGE 18, Drilling the wall panels and wall units
The wall plugs supplied are suitable for the following sub-surfaces:
Concrete, solid brick, ventilating brick, hollow concrete blocks.
If there is a different subsurface, select an appropriate fixing material.
Drill the 8-mm wall plug and
screw in the wall hook

11GENERAL CALEA ASSEMBLY INSTRUCTIONS
The wall plugs supplied are suitable for the following sub-surfaces:
Concrete, solid brick, ventilating brick, hollow concrete blocks.
If there is a different subsurface, select an appropriate fixing material.
Example installation height
for wall shelves = 10 increments
Drill the 8-mm wall plug
and screw in the wall hook
Drilling/installation dimensions for wall shelves with wooden shelves
WB105L/R, WBA105L/R
WB120L/R, WBA120L/R
WB135L/R, WBA135L/R
WB150L/R, WBA150L/R
WB165L/R, WBA165L/R
WB180L/R, WBA180L/R
WB195L/R, WBA195L/R
For other installation heights,
see order service card (graphic)

Drilling/installation dimensions H1 wall units
3x or 5x distance
spacers 75 x 75 x 8 mm
For H1 cabinet with
lighting
5.5x70 cylinder-head screw
and 8-mm wall plug + wall rails
WP5L/WP5R
Wood drill Ø8 mm
12 GENERAL CALEA ASSEMBLY INSTRUCTIONS
The wall plugs supplied are suitable for the following sub-surfaces:
Concrete, solid brick, ventilating brick, hollow concrete blocks.
If there is a different subsurface, select an appropriate fixing material.
H1-1, H1-11 H1-2, H1-7, H1-12, H1-17
H1-3, H1-4, H1-13, H1-14
H1-5, H1-8, H1-15, H1-18

13GENERAL CALEA ASSEMBLY INSTRUCTIONS
Drilling/installation dimensions H2 wall units
The wall plugs supplied are suitable for the following sub-surfaces:
Concrete, solid brick, ventilating brick, hollow concrete blocks.
If there is a different subsurface, select an appropriate fixing material.
5.5x70 cylinder-head screw and 8-mm wall plug
1x 55 cm rail per cabinet 63 cm,
2x 12.5 cm rails for cabinets 78 + 93 cm
2x 55 cm rails per cabinet 123 cm,
4x 12.5 cm rails per cabinet 153 + 223 cm, etc.
For installation height, see ORDER SERVICE
CARD
H2-1, H2-2, H2-3
H2-20, H2-21, H2-22,
H2-23/-24/-25/-26
H2-27, H2-29
H2-28, H2-30
H2-50, H2-51, H2-52, H2-53
H2-25, H2-36, H2-37,
H2-38/-39/-40/-41
H2-42, H2-44
H2-43, H2-45
H2-6, H2-7, H2-8 H2-6, H2-7, H2-8

Drilling/installation dimensions H3+ H6+ H7+ H8 wall units
For installation height, see ORDER SERVICE CARD
14 GENERAL CALEA ASSEMBLY INSTRUCTIONS
5.5x70 cylinder-head screw and 8-mm wall plug
1x 25 cm rail per cabinet 33 cm,
1x 40 cm rail per cabinet 48 cm,
1x 55 cm rail per cabinet 63 cm,
2x 12.5 cm rails for cabinets 78 + 93 cm
H6 cabinets
H3 cabinets
H3 cabinets
H7 cabinets
H8 cabinets
The wall plugs supplied are suitable for the following sub-surfaces:
Concrete, solid brick, ventilating brick, hollow concrete blocks.
If there is a different subsurface, select an appropriate fixing material.

CE100
HS5-238QL CE100-SV
HS5-238QR
15GENERAL CALEA ASSEMBLY INSTRUCTIONS
Drilling/installation dimensions HS5 wall units
5.5x70 cylinder-head screw and 8-mm wall plug
1x 25 cm rail,
1x 12.5 cm rail
The wall plugs supplied are suitable for the following sub-surfaces:
Concrete, solid brick, ventilating brick, hollow concrete blocks.
If there is a different subsurface, select an appropriate fixing material.

Fitting the drawer organiser
Adjusting the front gap by pushing
Press in the clips Slide in the glass panels
12
The profiles are preassembled in the
drawer
E1-45, E1-60, 3 glass panels each 298 x 70 x 4 mm
EK1-60, EK1-75, 3 glass panels each 378 x 70 x 4 mm
EK1-90, EK1-105, 4 glass panels each 378 x 70 x 4 mm
EK2-60, EK2-75, 3 glass panels each 378 x 170 x 4 mm
EK2-90, EK2-105, 4 glass panels each 378 x 170 x 4 mm
Push ttings
fitted to the cabinet, adjustable using the
magnetic locking system
Doors open by pushing!
+/-
16 GENERAL CALEA ASSEMBLY INSTRUCTIONS

+/-
click
On/off switch
for door
soft-close.
Align the door
vertically
Align the door horizontally
using the adjusting screw
Depth
adjustment
Hinge cover:
Use the offset cover for
offset hinges
Open
Fitting the hinge
+/-
+/-
The wall plugs supplied are suitable for the following sub-surfaces: Concrete, solid brick, ventilating
brick, hollow concrete blocks. If there is a different subsurface, select an appropriate fixing material.
No liability is assumed for injuries to persons or damage to property in the event of non-compliant
and/or incorrect installation.
Drawer-height fine adjustment
Drawer-side fine adjustment
+/-
+/-
Caution: Important information about LED lighting:
Only connect the lights to the safety transformers in accordance with EN 61558 (VDE
570) using 12-volt direct current (DC). The total power consumption of the connected
lights (see type label) must not exceed the transformer nominal capacity.
17GENERAL CALEA ASSEMBLY INSTRUCTIONS
Align the doors by adjusting the hinges

Drawer adjustment
+/-
18 GENERAL CALEA ASSEMBLY INSTRUCTIONS
Drawer tilt
adjustment
Drawer front
gap adjustment
Unhook the
drawer
Put the
drawer in

19GENERAL CALEA ASSEMBLY INSTRUCTIONS
CALEA lighting plan without radio remote control
This product contains a
light source of energy
efciency class „F“
„LEDSET2“ 2x L. 121 cm, 2x L.17 cm= 15.2 watt, 1x 6-way distributor;
„LEDSET3“ 2x L. 151 cm, 2x L.17 cm= 18.4 watt, 1x 6-way distributor;
„LEDSET4“ 2x L. 211 cm, 2x L.17 cm= 24.8 watt, 1x 6-way distributor;
„LEDSET5“ 2x L. 211 cm, 2x L.105 cm, 2x L.17 cm= 36.2 watt, 1x 6-way distributor;
LED sets for H1 cabinets
Self-adhesive LED profile „Q-Line Mini opal“
LED extension,
2 m only if required
LED extension,
2 m only if required
LED extension,
2 m only if required
LED 6-way distributor
LED 6-way distributor
On-site
socket
LED-Einbauleuchte „LST2“
2,6 Watt, 2m Zuleitung
LED glass shelf lighting 560 mm
„LG60“ 2,8 watt, 2 m supply cable
LED glass shelf lighting 410 mm „LG45“
1,9 watt, 2 m supply cable
LED glass shelf lighting 258 mm „LG30“
1,1 watt, 2 m supply cable
LED spotlight „LST4“ for shelf
1.4 watt, 2 m supply cable
LED lighting for angled shelves + wall units (2 m supply cable)
LED glass edge strip „LN225“/ „LN210“/ „LN195“/ „LN180“
L. 2200 mm/ 2050 mm / 1900 mm / 1750 mm, 10.6 watt / 9.8 watt / 9 watt / 8.4 watt
LED glass edge strip „LN165“/ „LN150“/ „LN135“/ „LN120“
L. 1600 mm / 1450 mm / 1300 mm / 1150 mm, 7.7 watt / 7 watt / 6.2 watt / 5 watt
LED glass edge strip „LN105“/ „LN90“/ „LN75“/ „LN60“
L. 1000 mm / 850 mm / 700 mm / 550 mm, 4.8 watt / 4.1 watt / 3.4 watt / 2.6 watt
„LEDSET1“ for wall panels
2x LED glass edge strip 85 cm
8.2 watt, 2 m supply cable
EVG LED, 10-way distributor, 12 V-DC (white plug), 30 watt, 230 V
length 5 m, with manual switch and flat Euro plug „LEVG30“
Test the lighting! If necessary, check plug connections. Push plug in completely.
Caution, Note the maximum transformer
load. Overloading the transformer reduces
its service life. Fault!
Important information about LED lighting:
Only connect the lights to the safety transformers
in accordance with EN 61558 (VDE 570) using
12-volt direct current (DC).

20 GENERAL CALEA ASSEMBLY INSTRUCTIONS
CALEA lighting plan with FKS4
This product
contains a light
source of energy
efciency class „F“
Alternatively: FKS4-60, 12 V-DC (white plug), 60 watt, 230 V
FKS4-60W with 60-watt transformer „FKS4-60“
EVG LED, 10-way distributor, 12 V-DC (white plug), 30 watt, 230 V
length 5 m, with manual switch and flat Euro plug „LEVG30“
„LEDSET1“ for wall panels
2x LED glass edge strip 85 cm
8.2 watt, 2 m supply cable
LED „LST2“ recessed light
2.6 watt, 2 m supply cable
12 V-DC (white plug)
LED extension,
2 m only if required
LED extension,
2 m only if required
LED extension,
2 m only if required
LED 6-way distributor
LED 6-way distributor
LED electrical storage
compartment with radio
remote control „FKS4“
(4- channel) Dimmable
up to max. 30 watt only if
requested by the customer
On-site
socket
4 pcs, 6-way
distributor,
max. 24 lights, max.
30 watt
when using LEVG30
max. 60 watt
LED glass shelf lighting 410 mm „LG45“
1,9 watt, 2 m supply cable
LED glass shelf lighting 258 mm „LG30“
1,1 watt, 2 m supply cable
LED glass shelf lighting
560 mm „LG60“ 2,8 watt,
2 m supply cable
„LEDSET2“ 2x L. 121 cm, 2x L.17 cm= 15.2 watt, 1x 6-way distributor;
„LEDSET3“ 2x L. 151 cm, 2x L.17 cm= 18.4 watt, 1x 6-way distributor;
„LEDSET4“ 2x L. 211 cm, 2x L.17 cm= 24.8 watt, 1x 6-way distributor;
„LEDSET5“ 2x L. 211 cm, 2x L.105 cm, 2x L.17 cm= 36.2 watt, 1x 6-way distributor;
LED glass edge strip „LN225“ / „LN210“ / „LN195“ / „LN180“
L. 2200 mm / 2050 mm / 1900 mm / 1750 mm, 10.6 watt / 9.8 watt / 9 watt / 8.4 watt
LED glass edge strip „LN165“ / „LN150“ / „LN135“ / „LN120“
L. 1600 mm / 1450 mm / 1300 mm / 1150 mm, 7.7 watt / 7 watt / 6.2 watt / 5 watt
LED glass edge strip „LN105“ / „LN90“ / „LN75“ / „LN60“
L. 1000 mm / 850 mm / 700 mm / 550 mm, 4.8 watt / 4.1 watt / 3.4 watt / 2.6 watt
LED spotlight „LST4“ for shelf
1.4 watt, 2 m supply cable
LED sets for H1 cabinets
Self-adhesive LED profile „Q-Line Mini opal“
Test the lighting! If necessary, check plug connections. Push plug in completely.
Caution, Note the maximum transformer
load. Overloading the transformer reduces
its service life. Fault!
Important information about LED lighting:
Only connect the lights to the safety transformers
in accordance with EN 61558 (VDE 570) using
12-volt direct current (DC).