GWINNER FELINO Instruction Manual

1GENERAL FELINO INSTALLATION + FES
GENERAL INSTALLING & FES
FELINO
IMAGE 1, Example wall-element combinations FE3 and FE1
IMAGE 2, Fit anti-tilt guard!
A fixing bracket with metal pin is fitted
as anti-tilt guard to all 5R and 8R base
units to prevent them from tipping
forward. A 5x60 mm countersunk
screw and an 8 mm dia. plastic wall
plug are used. The 12 mm cover plate
only covers the fitting when mounted
at an angle.
+/-
Press levelling glides
into holes provided and
align units
4x17 roundhead
screw
5.5x70 cheese-head
screw
FROM RE5247
Qualied specialist personnel
PLEASE NOTE!
CAUTION! Follow the specications carefully when tting wall units. Secure all
elements that may tip with the anti-tip mechanisms supplied.
Wall plug,
dia. 8 mm

2GENERAL FELINO INSTALLATION + FES
IMAGE 3, Align units and install cover panel
IMAGE 4
5.5x70 cheese-head
screw + 8 mm wall plug
The wall plugs supplied are suitable for the following sub-surfaces:
Concrete, solid brick, ventilating brick, hollow concrete blocks.
If there is a different subsurface, select an appropriate fixing material.
+/-
Secure 12 mm cover panels
in place from inside at points
marked. 4x27 mm countersunk
screw and cover caps
Ø 5 mm nickel-plated cover
cap, fit on holes not used in
cabinet sides.
M4x 28 connecting screw
with sleeve nut
Connect units
Press levelling glides into holes
provided and align units
To install wall
panels, see separate
installation
instructions!

Adjusting the wall units–
Caution! Check from above
that all ttings have been tted
in the rails.
Upper adjustment screw
= depth adjustment
Lower adjustment screw
= height adjustment
To attach wall units to the wall, fasten mounting rails (provided) to the wall using 8 mm dia. plastic
wall plugs and 5x70 mm pan-head screws (Fig. 4, centre hole = top edge of carcase less 49 mm)
3GENERAL FELINO INSTALLATION + FES
Note: Please refer to the dimension
scheme attached for other
IMAGE 5
IMAGE 6
Hanging the
wall unit
To install anti-tilt
guard, see image. 2
To install top panel,
see image 3

Adjusting the wall units–
Caution! Check from above that all
ttings have been tted in the rails.
4GENERAL FELINO INSTALLATION + FES
IMAGE 7
IMAGE 8, Hängeschränke aufhängen
5.5x70 cheese-head
screw + 8 mm wall plug
To install wall
panels, see
separate
installation
instructions!
The wall plugs supplied are suitable for the following sub-surfaces:
Concrete, solid brick, ventilating brick, hollow concrete blocks.
If there is a different subsurface, select an appropriate fixing material.
Upper adjustment screw
= depth adjustment
Lower adjustment screw
= height adjustment

+/-
Fit steel dowel
with barrel nut on
upper wall panel
Fit connector housing with
M6 threaded stud on lower
wall panel, connect panel
and tighten fitting.
Upper wall panel
5GENERAL FELINO INSTALLATION + FES
IMAGE 9, FE1 assy.
IMAGE 10, Connect 19 mm wall panels with glass shelf
To install upper wall
panel with shelf, see sep.
installation instructions!
4x adjusting spindles M8x15
+ mounting plate 40x15x2
+ panhead screws 3.5x17
2
4
1
3
Always press
plastic sleeve into
countersink! Sleeve
or screw must
not be allowed
to protrude!
Glass base with holes

Installing handle on base-unit drawers Installing handle on glass doors with double
glass panel
Screw-mount handles with 2 x M4x25
plate screws + 2 x plastic sleeves.
+/-+/-+/-
6GENERAL FELINO INSTALLATION + FES
IMAGE 11, Drill holes in 19mm wall panels
IMAGE 12, Hang 19mm wall panels
Handle installation
The wall plugs provided are suitable
for the following mounting surfaces:
concrete, solid brick masonry, cored block
masonry, hollow block masonry. Select
the appropriate fixings for other mounting
surfaces.
Drill holes for 8 mm wall plug and
screw in wall hooks
Adjusting
wall panel
Screw-mount handles with
3.5x17 countersunk head screw
6 ea. for 130 cm handle,
9 ea. for 195 cm handle
Adjusting wall panels – Caution!!
From above, make sure all ttings are engaged in wall hook.

+
-
+
-
+
-
7GENERAL FELINO INSTALLATION + FES
Align the doors by adjusting the hinges
Installing handles + drawers Installing handle on drawers at top - „S1O-65“
Handle installation
Screw-mount handles with
2 x M4x25 countersunk screws.
Screw-mount handles with
2 x M4x25 plate screws.
Precision drawer height adjustment
+/-
click
On/off switch
for door
soft-close.
Align the door
vertically
Align the door horizontally
using the adjusting screw
Depth
adjustment
Hinge cover:
Use the offset cover for
offset hinges
Open
Fitting the hinge
+/-
+/-
The wall plugs supplied are suitable for the following sub-surfaces: Concrete, solid brick, ventilating
brick, hollow concrete blocks. If there is a different subsurface, select an appropriate fixing material.
No liability is assumed for injuries to persons or damage to property in the event of non-compliant
and/or incorrect installation.
Caution: Important information about LED lighting:
Only connect the lights to the safety transformers in accordance with EN 61558 (VDE
570) using 12-volt direct current (DC). The total power consumption of the connected
lights (see type label) must not exceed the transformer nominal capacity.

Montage Schubkasteneinteilung
Front gap adjustment with magnet
Push in clips Slide in glasses
12
Profiles are pre-assembled in the drawer
8GENERAL FELINO INSTALLATION + FES
ET1-98, EK1-98, E1-98, 4 glasses 476 / 376 / 296x70x4 mm
ET2-98, EK2-98, E2-98, 4 glasses 476 / 376 / 296x170x4 mm
ET2-65, EK2-65, E2-65, 3 glasses 476 / 376 / 296x170x4 mm
ET1-65, EK1-65, E1-65, 3 glasses 476 / 376 / 296x70x4 mm
Adjust the front gap by turning the magnet with a screwdriver.
(For large glass cabinet doors + lower section flaps)
+/-+/-+/-

9GENERAL FELINO INSTALLATION + FES
Rasterhöhen (1Raster = 176mm) Bohr- / Einbaumaße Hängeschränke
49
Hänge-
Bohrbilder Hängeschränke
54 542 54
650
4R= 704
54 542 54
schrank 9R-65
7291266
Hänge-
54 380 54
9R= 1584
488
schrank 9R-49 Hänge-
schrank 4R-65
49 1467
4R= 704
54 542 54
Hänge- schrank 4R-65
49 1643
650
650
54 542
650
542 54108
2x Hängeschrank 4R-65
650
54 542
650
542 54108
3x Hängeschrank 4R-65
650 650
108 542
49
4R= 704
49
Hänge-
54 542 54
650
schrank 9R-65
5531266
Hänge-
54 380 54
9R= 1584
488
schrank 9R-49
Height grid for FELINO wall units with 1.5 incr. base
wall unit,
4 incr.-65
wall unit,
4 incr.-65
wall unit,
4 incr.-65
wall unit,
4 incr.-65
wall unit,
4 incr.-49
wall unit,
4 incr.-49
2x wall unor 4 incr.-65 3x wall unor 4 incr.-65
Rasterhöhen (1Raster = 176mm) Bohr- / Einbaumaße Hängeschränke
49
Hänge-
Bohrbilder Hängeschränke
54 542 54
650
4R= 704
54 542 54
schrank 9R-65
7291266
Hänge-
54 380 54
9R= 1584
488
schrank 9R-49 Hänge-
schrank 4R-65
49 1467
4R= 704
54 542 54
Hänge- schrank 4R-65
49 1643
650
650
54 542
650
542 54108
2x Hängeschrank 4R-65
650
54 542
650
542 54108
3x Hängeschrank 4R-65
650 650
108 542
49
4R= 704
49
Hänge-
54 542 54
650
schrank 9R-65
5531266
Hänge-
54 380 54
9R= 1584
488
schrank 9R-49
Drilling/installation dimensions for wall units
Increment heights (1 incr. = 176 mm)
UT
Rasterhöhen (1Raster = 176mm) Bohr- / Einbaumaße Hängeschränke
49
Hänge-
Bohrbilder Hängeschränke
54 542 54
650
4R= 704
54 542 54
schrank 9R-65
7291266
Hänge-
54 380 54
9R= 1584
488
schrank 9R-49 Hänge-
schrank 4R-65
49 1467
4R= 704
54 542 54
Hänge- schrank 4R-65
49 1643
650
650
54 542
650
542 54108
2x Hängeschrank 4R-65
650
54 542
650
542 54108
3x Hängeschrank 4R-65
650 650
108 542
49
4R= 704
49
Hänge-
54 542 54
650
schrank 9R-65
5531266
Hänge-
54 380 54
9R= 1584
488
schrank 9R-49
11,5 inc. 10,5 inc. 9,5 inc. 8,5 inc. 6,5 inc. 4,5 inc. 2,5 inc. 1,5 inc. Base height

Height grid for FELINO wall units with 2.3 incr. base
Rasterhöhen (1Raster = 176mm) Bohr- / Einbaumaße Hängeschränke
49
Hänge-
Bohrbilder Hängeschränke
54 542 54
650
4R= 704
54 542 54
schrank 9R-65
8611266
Hänge-
54 380 54
9R= 1584
488
schrank 9R-49 Hänge-
schrank 4R-65
49 1599
4R= 704
54 542 54
Hänge- schrank 4R-65
49 1775
650
650
54 542
650
542 54108
2x Hängeschrank 4R-65
650
54 542
650
542 54108
3x Hängeschrank 4R-65
650 650
108 542
49
4R= 704
49
Hänge-
54 542 54
650
schrank 9R-65
6851266
Hänge-
54 380 54
9R= 1584
488
schrank 9R-49
Rasterhöhen (1Raster = 176mm) Bohr- / Einbaumaße Hängeschränke
49
Hänge-
Bohrbilder Hängeschränke
54 542 54
650
4R= 704
54 542 54
schrank 9R-65
8611266
Hänge-
54 380 54
9R= 1584
488
schrank 9R-49 Hänge-
schrank 4R-65
49 1599
4R= 704
54 542 54
Hänge- schrank 4R-65
49 1775
650
650
54 542
650
542 54108
2x Hängeschrank 4R-65
650
54 542
650
542 54108
3x Hängeschrank 4R-65
650 650
108 542
49
4R= 704
49
Hänge-
54 542 54
650
schrank 9R-65
6851266
Hänge-
54 380 54
9R= 1584
488
schrank 9R-49
10 GENERAL FELINO INSTALLATION + FES
Rasterhöhen (1Raster = 176mm) Bohr- / Einbaumaße Hängeschränke
49
Hänge-
Bohrbilder Hängeschränke
54 542 54
650
4R= 704
54 542 54
schrank 9R-65
7291266
Hänge-
54 380 54
9R= 1584
488
schrank 9R-49 Hänge-
schrank 4R-65
49 1467
4R= 704
54 542 54
Hänge- schrank 4R-65
49 1643
650
650
54 542
650
542 54108
2x Hängeschrank 4R-65
650
54 542
650
542 54108
3x Hängeschrank 4R-65
650 650
108 542
49
4R= 704
49
Hänge-
54 542 54
650
schrank 9R-65
5531266
Hänge-
54 380 54
9R= 1584
488
schrank 9R-49
UT
wall unit,
4 incr.-65
wall unit,
4 incr.-65
wall unit,
4 incr.-65
wall unit,
4 incr.-65
wall unit,
4 incr.-49
wall unit,
4 incr.-49
2x wall unor 4 incr.-65 3x wall unor 4 incr.-65
12,3 inc. 11,3 inc. 10,3 inc. 9,3 inc. 7,3 inc. 5,3 inc. 3,3 inc. 2,3 inc. Base height
Drilling/installation dimensions for wall units
Increment heights (1 incr. = 176 mm)

Lighting diagram - Felino without FKS
Test lighting!
If necessary, check plug
connections. Press plug in all the way.
Caution! Pay attention to max. transformer
load. Overloading the transformer will
shorten its useful life! Fault!!!
Important note on LED lighting:
Only connect lights to safety transformers
in compliance with EN 61558 (VDE 570),
12-volt direct current (DC).
bauseitige Steckdose
L=1m L=3,85m L=0,15m
1 Watt, Zuleitung 2m
für Wandpaneele "LSP1" LED-Verlängerung
2m, nur bei Bedarf
EVG-LED, 10fach-Verteiler, 12V-DC (weißes Stecksystem), 30Watt, 230V
L. 5m, mit Handschalter und Euro-Flachstecker "LEVG30"
LED-Einbauleuchte "LST2"
2,6 Watt, Zuleitung 2m LED-Verlängerung
2m, nur bei Bedarf
12V-DC (weißes Stecksystem)
12V-DC, (weißes Stecksystem)
LED-Aufbauleuchte Ice-Line A "LB174"
L1740mm, 5,1Watt, 2m Zuleitung
12V-DC (weißes Steckersystem)
LED-Aufbauleuchte Ice-Line A "LB144"
L1440mm, 4,2Watt, 2m Zuleitung
12V-DC (weißes Steckersystem)
LED-Aufbauleuchte Ice-Line A "LB114"
L1140mm, 3,3Watt, 2m Zuleitung
12V-DC (weißes Steckersystem)
L=1m L=3,85m L=0,15m
EVG-LED, 6fach-Verteiler, 12V-DC (weißes Stecksystem), 15Watt, 230V
L. 5m, mit Handschalter und Euro-Flachstecker "LEVG15"
LED-Vorbauleuchte
This product contains a light
source of energy efficiency class
"F"
Mont-FE allg.+FES-ab R5247_Engl.xlsx 15.10.2018 / GRO Page 9/10
This product contains a
light source of energy
efciency class „F“
FELINO lighting plan without radio remote control
Test the lighting! If necessary, check plug connections. Push plug in completely.
Caution, Note the maximum transformer
load. Overloading the transformer reduces
its service life. Fault!
Important information about LED lighting:
Only connect the lights to the safety transformers
in accordance with EN 61558 (VDE 570) using
12-volt direct current (DC).
LED extension,
2 m only if required
LED extension,
2 m only if required
On-site
socket
Fitted LED light „LST2“
2.6 W, 2-m cable
12 V DC (white plug system)
LED surface luminaire Ice-Line A „LB174“
L = 1740 mm, 5.1 W, 2-m cable
12 V DC (white plug system)
LED surface luminaire Ice-Line A „LB144“
L = 1440 mm, 4.2 W, 2-m cable
12 V DC (white plug system)
LED surface luminaire Ice-Line A „LB114“
L = 1140 mm, 3.3 W, 2-m cable
12 V DC (white plug system)
EVG LED, 10-way distributor, 12 V-DC (white plug), 30 watt, 230 V
length 5 m, with manual switch and flat Euro plug „LEVG30“
EVG LED, 6-way distributor, 12 V-DC (white plug), 15 watt, 230 V
length 5 m, with manual switch and flat Euro plug „LEVG15“
LED surface-mounted
luminaire for wall panels „LS1P1“
1 W, 2-m cable
12 V DC (white plug system)
11GENERAL FELINO INSTALLATION + FES

FELINO lighting plan with FKS4
bauseitige
LED-Verlängerung
2m, nur bei Bedarf
LED-Einbauleuchte "LST2"
2,6 Watt, Zuleitung 2m
12V-DC (weißes Stecksystem)
LED-Aufbauleuchte Ice-Line A "LB174"
L1740mm, 5,1Watt, 2m Zuleitung
12V-DC (weißes Steckersystem)
L=1m L=3,85m L=0,15m
EVG-LED, 6fach-Verteiler, 12V-DC (weißes Stecksystem), 15Watt, 230V
L. 5m, mit Handschalter und Euro-Flachstecker "LEVG15"
LED-Aufbauleuchte Ice-Line A "LB144"
L1440mm, 4,2Watt, 2m Zuleitung
12V-DC (weißes Steckersystem)
LED-Aufbauleuchte Ice-Line A "LB114"
L1140mm, 3,3Watt, 2m Zuleitung
12V-DC (weißes Steckersystem)
L=1m L=3,85m L=0,15m
EVG-LED, 10fach-Verteiler, 12V-DC (weißes Stecksystem), 30Watt, 230V
L. 5m, mit Handschalter und Euro-Flachstecker "LEVG30"
Steckdose
1 Watt, Zuleitung 2m
für Wandpaneele "LSP1"
12V-DC, (weißes Stecksystem)
LED-Vorbauleuchte
Test the lighting! If necessary, check plug connections. Push plug in completely.
Caution, Note the maximum transformer
load. Overloading the transformer reduces
its service life. Fault!
Important information about LED lighting:
Only connect the lights to the safety transformers
in accordance with EN 61558 (VDE 570) using
12-volt direct current (DC).
LED extension,
2 m only if required
This product
contains a light
source of energy
efciency class „F“
Fitted LED light „LST2“
2.6 W, 2-m cable
12 V DC (white plug system)
LED surface luminaire Ice-Line A „LB144“
L = 1440 mm, 4.2 W, 2-m cable
12 V DC (white plug system)
LED surface luminaire Ice-Line A „LB114“
L = 1140 mm, 3.3 W, 2-m cable
12 V DC (white plug system)
LED surface luminaire Ice-Line A „LB174“
L = 1740 mm, 5.1 W, 2-m cable
12 V DC (white plug system)
LED surface-mounted
luminaire for wall panels „LS1P1“
1 W, 2-m cable
12 V DC (white plug system)
EVG LED, 6-way distributor, 12 V-DC (white plug), 15 watt, 230 V
length 5 m, with manual switch and flat Euro plug „LEVG15“
EVG LED, 10-way distributor, 12 V-DC (white plug), 30 watt, 230 V
length 5 m, with manual switch and flat Euro plug „LEVG30“
On-site
socket
LED electrical storage
compartment with radio remote
control „FKS4“ (4- channel)
Dimmable up to max. 30 watt
only if requested by the customer
4 pcs, 6-way distributor,
max. 24 lights,
max. 30 watt
when using LEVG30,
max. 60 watt
when using LEVG15
12 GENERAL FELINO INSTALLATION + FES