H.Koenig oly900 User manual

oly900
Oil press
Presse à huile
Ölpress
Oliepress
Prensa de aceite
Pressa per olio

ENGLISH
Please read carefully this user manual and all the safety precautions
before using the product.
SAFETY INSTRUCTIONS
• When using electrical appliances, basic safety precautions should
be observed, including the following:
• Make sure that your output voltage corresponds to the voltage
stated on the rating label of the appliance.
• If the appliance orits power cord has been damaged, it must be
repaired or replaced by the manufacturer, a service technician, or a
similarly qualified person, to prevent hazards.
• Before cleaning the appliance, be sure that it has cooled completely
and that it is unplugged from the outlet.
• To protect yourself from electric shock, do not immerse the power
cord, plug, or appliance in water or other liquids.
• Misuse of this appliance may result in severe personal injury.
• Always unplug the unit prior to assembly, after use, before cleaning,
and in the event of any malfunction.
• Always unplug the unit before opening the bean or collection
container and before removing either from the housing.
• This appliance may be used by persons with reduced physical,
sensory or mental capabilities or lack of experience or knowledge,
provided that they are supervised or instructed in the safe use of the
appliance and that they fully understand the potential hazards.

• Before each use, check the appliance, its power cord, and its
attachments for any defects. If the appliance has been dropped or if
excessive force has been used to pull the power cord or plug, then
the appliance should not be used because even invisible damage
may have adverse effects on the operational safety of the appliance.
• The appliance and its cord must never be placed near or on top of
hot surfaces such as a radiator, ovens, gas burners, open flames,
etc.
• When unplugging the unit, always grip the plug itself. Do not jerk or
pull the power cord.
• Do not allow the cord to hang over the edge of the counter or table.
• This appliance may be used by children of at least 8 years of age,
as long as they are supervised and have been given instructions
about using the appliance safely and are fully aware of the dangers
involved.
• Cleaning and maintenance should not be carried out by children
unless they are at least 8 years of age and are supervised by an
adult.
• Keep the appliance and its power cord out of reach of children
under 8 years of age.
• When using electrical equipment, safety precautions must always
be taken to prevent the risk of fire, electric shock and/or injury in the
event of misuse.
• Make sure that the voltage rating on the typeplate corresponds to
your main voltage of your installation. If this is not the case, contact
the dealer and do not connect the unit

• Please keep this document at hand and give it to the future owner
in case of transfer of your device
• Never leave the unit unattended while in operation.
• The device must not be used if it has been dropped, it obvious signs
of damage are visible or if it has leaks.
• This appliance is intended for use in domestic and similar
applications such as :
- kitchen areas in shops, offices and other working environments
- farmhouses
- in hotels, motels and other residential environments
- guest rooms.
* Please do not use the machine for other purposes outside of its
original function.
KEE P AWAY FROM WATER
KEE P AWAY FROM FIRE
KEE P OUT OF REACH OF
CHILDREN
DO NOT DISSASEMBLE
DO NOT INSERT BODY PARTS
IN
THE DEVICE
WHEN IT’S HOT, DO NOT
TOUCH MOVING PARTS
WHEN OPERATING

DO NOT POUR LIQUID INTO
THE HOPPER
DO NOT TOUCH THE OIL
COLLECTOR WHEN
OPERATING
NOTE:
Do not try to change parts
or the power
The machine is designed to
process sunflower seeds,
pumpkin seeds, flaxseed,
sesame, rapeseed, peanuts,
walnuts, etc. Donot try to
process anything else but the
seeds and nuts we advise you
to! Consult the list of
processable items in this user
manual.
GENERAL DESCRIPTION
TECHNICAL SPECIFICATIONS
SWITCHING CONTROL: ON / OFF
DIMENSIONS: 355 * 178 * 264 mm
THERMAL CONTROL: Temperature probe + Thermal protection
MOTOR POWER: 180 W
HEATING MODE: Heating element and extrusion shaft
HEATING POWER: 330 W
OUTPUT POWER: 510 W
VOLTAGE RATING: 220-240V~/50-60 HZ
WEIGHT: 6,8 KG

ACCEPTED SEEDS
Brown flax seeds
Mustard seeds
Chia seeds
Cashews nuts
Peanuts
Hazelnuts
Raw coconut
Almonds
Pistachios
Hemp seeds
Grape seeds
Sunflower seeds
Macadamia nuts
Walnuts
Rapeseed
Brazil nuts
Pine nuts
Pumpkin seeds
Poppy seeds
Sesame seeds
Pecans
Argan seeds
Coriander seeds
We advise you to dry/dehydrate your seeds before use.
WARNING : This oil press does not allow the extraction of
olive oil.
HOW TO USE THE OIL PRESS MACHINE
1. Rotate to open the hopper
lid.
2. Put the ingredients in the hopper.
Note : Please use clean and high oil content ingredients
(dried). If they contain stones, sand or metal, this could
damage inner parts. Ingredients larger than a peanut should
be cut into smaller pieces before being inserted.

3. Close the hopper lid and put
the oil box in the place.
Note : The hopper lid must be
in correct position otherwise the
machine won’t work.
4. Put the residue box
below the extrusion hole;
5. Connect to the power source
and press the Power button,
the selection screen will be lit.
6. Select the proper program, according to the
ingredient you are using.*
The oil pressing machine has 7 Presets as follows:
Peanuts, Sesame, Sunflower Seeds, Rapeseeds,
Flaxseeds, Walnut Core, Mixed. Select the proper program
for the ingredient you are using. If the seed or nut is not
listed, consult the matching table.
7. Press the Start/ Pause
button, the light will flash when
the machine starts to preheat.
8. Preheating will last for about
30 seconds - 1 minute,
depending on the program you
have selected, then, the
pressing operation will start.
9. The machine will
automatically stop after 1
minute and power off after
5 minutes if the hopper
has no ingredients inside.
You need to press the
Power button to start
squeezing again.
10. The machine will
automatically stop for cooling
down if it has been working for
more than 45 minutes. Then, it
won`t work for the next 30
minutes. However, if you need
to force starting it, you have to
pull
out the power plug for 10
seconds and connect it again to
work).

11. When the oil press jams, please press the Start/Pause button and the press Reverse for 5
seconds. The ingredients will be pushed into reverse, unjamming the oil pressing machine.
Press the Start/Pause
button to operate it again. Please keep in mind that if this happens 3 times, it will enter
protection mode and it will not work until stopped and powered again.
CLEANING AND MAINTENANCE
1.
We recommend that you leave the machine to cool down a bit, after
it has been used, but still, the items have to be like warm, so this will
ease your job, the residues will not stick to the metal parts.
2.
Remove the protection cover.
3.
Unscrew the extrusion shaft with the special spanner included in the
box, in a counterclockwise direction and then take out the outer part.
4.
Clean the extrusion shaft and its outer element with a soft towel or
cloth. Corrosive detergent should not be used.

5.
Clean the outer element with the brush and make sure there is no
residue inside.
Leakage prevention board
6.
Fix the extrusion shaft and then the outer element when you
assemble the machine.
TROUBLESHOOTING
NO.
PROBLEM:
SOLUTIONS:
1
Screw extrusion shaft got
stuck
A: Press the “reverse” button for 5 seconds and the
extrusion shaft will reverse back the ingredients. Then
press “Start/Pause” button.
B: Turn off and pull out the plug. Disassemble the out
element and extrusion shaft, clean the items as well as
the hopper and its entrance. Assemble it back!
2
Motor stops rotating and
doesn’t squeeze oil
A: It is normal for the motor to take 30-45 seconds to
preheat the extrusion shaft before it starts squeezing.
B: Check if the hopper lid or oil box are in the correct
position.

3
The motor stops without
any notice while the
machine is working
A: If it has been working for more than 45 minutes, it is
normal that it enters self protection mode.
B: If more than a minute has passed from the last
processed ingredient, it is normal the oil presing
machine has stopped.
C: If the oil pressing machine has stopped 3 times,
because being jammed, it will enter as well, in self
protection mode.
TIPS & TRICKS
To make high quality oil and avoid the machine getting stuck or parts damaging, please select good
quality ingredients, with high oil content, without stones or sand otherwise it will damage parts or stuck
the machine.
Use ingredients with high oil content, avoid ingredients that are rotten, oxidized or have low oil content.
Soybean is not a proper ingredient, please avoid it!
Special tip for peanuts: we suggest you fry the peanuts before pressing them. Fry them at 80
centigrades but don’t over fry them because the beans could get burn.
The oil extraction rate is very good if the ingredients are dry up to 90%. For better results, we
reccomend you to dry the ingredients for about 1 hour under the sun or in a dehydrator at 60
centigrades.
It is necessary to clean the extrusion shaft with a clean and soft cloth or towel after every use. Try not
to use water, don`t use detergent!
Depending on the type of ingredient you are using, it processes around 100-150 g of ingredients every
5 minutes.
The efficiency of the squeezing process is between 30-75 %, depending on ingredients, for instance,
out of 100 g of walnuts, you can squeeze about 75 ml of oil, out of 100 g of flaxseed you get around 45
ml of oil.
Freshly squeezed oil is not clear, it has sediments, after a while, if it is not stirred, the sediment settles.
Anyway, the oil is cold pressed, it does not oxidize, it is a natural source of proteins, vitamins and fatty
acids.
The residue can be used for preparing food or as a sauce material.