H3C SecPath M9000-AI NSQM5AIASKA1 User manual

Manual version: 6PW102-20230321
BOM: 3123A1XP
i
H3C SecPath M9000-AI NSQM5AIASKA1 AI security
engine module
1 Identifier
The module identifier NSQM5AIASKA1 is on the far right of the front panel.
2 About the module
The NSQM5AIASKA1 AI security engine module provides one console port, one management
Ethernet copper port, one BMC console port, one BMC network port, two 10GBASE-R-SFP+ fiber
ports, one SUV connector, and one USB port.
3 Specifications
Figure 1 Front panel
(1) Ejector lever
(2) NVMe SSD slots
(3) 10GBASE-R-SFP+ fiber ports
(4) USB port
(5) Console port
(6) Management Ethernet copper port
(7) BMC console port
(8) BMC network port
(9) UID button/LED
(10) Power on/standby button
(11) Captive screw
(12) System status LED
(13) BMC network port ACT LED
(14) BMC network port LINK LED
(15) Management Ethernet copper port ACT LED
(16) Management Ethernet copper port LINK LED
(17) 10GBASE-R-SFP+ fiber port LEDs
(18) SUV connector
Table 1 Module specifications
Item
Specification
Memory 64GB (one 32GB DIMM per CPU)
Storage 1920GB (two 960GB SATA SSDs are provided with the module)
Two NVMe SSD slots are on the front panel for storage expansion.
You can purchase and install 2TB NVMe SSDs in the slots.
Number of CPUs 2
Dimensions (H × W × D) 50 × 433 × 520 mm (1.97 × 17.05 × 20.47 in)
Weight 9.64 kg (21.25 lb)
12345678910 11
12
13
14
18 17 15
16

Manual version: 6PW102-20230321
BOM: 3123A1XP
ii
Item
Specification
Power consumption 165 W to 462 W
Hot swapping Supported
Ports
•1 × console port (See Table 2 for port specifications)
•1 × management Ethernet copper port (See Table 3 for port
specifications)
•1 × BMC console port (See Table 2 for port specifications)
•1 × BMC network port (See Table 3 for port specifications)
•2 × 10GBASE-R-SFP+ fiber ports
•1 × SUV connector
•1 × USB port
Available transceiver modules 10GBASE-R-SFP+ fiber ports: See Table 4.
Compatible devices and slots
•M9000-AI-E8 multiservice gateway (slots 0 to 3)
•M9000-AI-E16 multiservice gateway (slots 0 to 3 and slots 4 to
7)
Table 2 Console port/BMC console port specifications
Item
Specification
Connector RJ-45
Interface standard RS-232
Transmission baud rate •Console port: 9600 bps (default) to 115200 bps
•BMC console port: 38400 bps (default)
Transmission medium Asynchronous serial cable
Transmission distance ≤15 m (49.21 ft)
Services
•Provides connection to an ASCII terminal.
•Provides connection to the serial port of a local PC running a
terminal emulation program.
•Supports the command line interface (CLI)
Table 3 Management Ethernet copper port/BMC network port specifications
Item
Specification
Connector RJ-45
Interface standard 802.3, 802.3u, and 802.3ab
Interface type MDI/MDIX autosensing
Transmission medium Category-5 or above twisted pair cable
Transmission distance 100 m (328.08 ft)
Transmission rate and duplex mode
•10 Mbps, half/full duplex
•100 Mbps, half/full duplex
•1000 Mbps, full duplex

Manual version: 6PW102-20230321
BOM: 3123A1XP
iii
Table 4 SFP+ transceiver module specifications
Module Central
wavelength Connector type Cable specifications
Maximum
transmission
distance
SFP-XG-SX-MM850-A 850 nm LC 50/125 µm MMF 300 m (984.25 ft)
SFP-XG-LX-SM1310 1310 nm LC 9/125 µm SMF 10 km (6.21 miles)
4 LEDs
The module provides LEDs to indicate the operating status of the module and ports.
Table 5 LED description
LED
Mark
Status
Description
System status LED
Steady green The system is operating correctly or in
standby state.
Flashing green HDM is initializing.
Flashing amber An alarm has occurred.
Management
Ethernet copper port
LED/BMC network
port LED
LINK
ACT
ACT
On Flashing A link is present on the port and the port is
sending and receiving data.
On Off A link is present on the port.
Off Off No link is present on the port.
10GBASE-R-SFP+
fiber port LED 0/1
Flashing The port is receiving or sending data.
On A link is present on the port.
Off No link is present on the port.
Power on/standby
button LED
Steady green The system has started.
Flashing green The system is starting.
Steady amber The system is in standby state.
Flashing amber A power anomaly has occurred.
Off No power is present.
UID button LED UID
On The UID LED is activated.
Flashing (1 Hz) The system is being managed from HDM
or the firmware is being upgraded.
Flashing (4 Hz) HDM is restarting. To restart HDM, press the UID button LED for a minimum of eight
seconds.
Off The UID LED is not activated.

Manual version: 6PW102-20230321
BOM: 3123A1XP
iv
5 Related documentation
For information about upgrading the module, see the release notes for the device.
For information about installing the module, see the installation guide for the device.
Copyright © 2023 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.