H3C MSR 3600 User manual

Introduction to installation accessories 安装附件介绍
Wear an ESD-preventive wrist strap, and make sure the wrist strap makes good skin
contact and is well grounded.操作者需佩戴防静电腕带，确保防静电腕带与皮肤良好
接触，并确认防静电腕带已经良好接地。
The installation tools are not provided with the router. Prepare them yourself.
路由器不随机提供安装工具，请用户根据实际安装需求自己准备安装工具。
Mounting the router to a workbench 安装路由器到工作台
2
1
BOM:3104A0HF
Tool list 工具参考
!
H3C MSR 3600 Routers Installation Quick Start (For MSR3620-DP)-6PW103
H3C MSR 3600路由器 快速安装指南(For MSR3620-DP)-6PW103
Flathead screwdriver
一字螺丝刀 Phillips screwdriver 十字螺丝刀 Needle-nose pliers 尖嘴钳 Wire-stripping pliers 剥线钳
ESD wrist strap
防静电腕带
Diagonal pliers
斜口钳 Blow dryer 热吹风 Network cable tester 测线仪
Multimeter
万用表
Marker
记号笔
Cage nut
(user supplied)
浮动螺母(用户自备)
Grounding cable
地线
Rubber feet
胶垫贴
M4 screw
M4 螺钉
M6 screw
(user supplied)
M6 螺钉(用户自备)
Front mounting
brackets
前挂耳
Removable cable tie
(user supplied)
可拆卸式扎带(用户自备)
Load-bearing screw
承重螺钉
Rear mounting brackets
后挂耳
Stick the rubber pads to the appropriate
positions on the router bottom.
粘贴胶垫到路由器底部。
Mount the router to the workbench.
将路由器安装到工作台。
Mounting the router to a rack 安装路由器到机柜
Attach cage nuts and rear mounting brackets to the rack. 安装浮动螺母及后挂耳。

4
3
Connecting the grounding cable 连接保护地线
Correctly connecting the router grounding cable is crucial to lightning protection and
EMI protection. 路由器地线的正确连接是路由器防雷、防干扰的重要保障，请使用设备
随机提供的保护地线正确接地。
Attach the mounting brackets to the router. 安装挂耳到路由器。
Install the router in the rack. 安装路由器到机柜。
To mount the router in a rack, make sure the rack is reliably grounded. To ground the router
in a rack, connect the grounding cable of the building to the grounding strip on the rack, and
then use the grounding cable of the router to connect the router to the grounding strip on the
rack. 路由器安装在机柜时，要求机柜已经良好接地，首先需将楼宇保护地线与机柜接地排相
连，然后使用接地线将路由器与机柜接地排相连。

6
5
Installing interface cards 安装接口模块
SICs are not hot swappable.
SIC接口模块不支持热插拔。
Install an HMIM. HMIMs are hot swappable.
安装HMIM接口模块，支持热插拔。
Remove the dust plug from the fiber port, insert the transceiver module into the fiber port,
and connect the optical fibers to the port. 取下以太网光口上的防尘盖，将光模块插入以太
网光口接口，将光纤插入光模块。
Connecting optical fibers to an SFP port 安装光模块
To install a power module:
1. Remove the filler panel from the power module slot.
2. Insert the AC/DC power module in the slot.
3. Fasten the captive screw on the power module.
拆卸电源槽位假面板，插入AC/DC电源模块，旋紧固定螺钉。
AC power module
AC电源模块
DC power module
DC电源模块
Connecting the power cord 连接电源线
To connect the power cord:
1. Connect one end of the power cord to the router and use the bail latch to secure the
power cord plug in position.
2. Connect the other end to the power source. Arrange the power cord neatly and keep it
away from high-temperature, wet, or sharp objects.
安装路由器时，应将电源线摆放整齐，避免与高温、潮湿或尖锐的物品触碰。电源线的两端
应分别与路由器和供电设备紧密相连，并使用电源线卡勾固定，避免因人员走动或触碰，勿
将电源线松脱的情况发生。
Make sure the router is reliably grounded before you connect the power cord.
在连接电源线前，需保证设备已正确接地。
When you connect the power cord, make sure the power switch on the power module
is off. Connect the power cord to the router first and then to the power supply system in
the equipment room. 在连接电源线时，请确认路由器电源开关处于关闭状态，先完成
电源线与路由器侧的连接，再进行电源线与机房供电系统的连接，以免造成人身伤害。
123
Installing power modules 安装电源模块
Power modules are hot swappable. 电源模块支持热插拔。

7
Obtaining documentation 资料获取方式
Connect the DC power cord.
连接直流电源线。
Connect the AC power cord.
连接交流电源线。
To access the most up-to-date H3C product documentation on the H3C website at
www.h3c.com.hk:
1. Go to http://www.h3c.com.hk/Technical_Documents.
2. Choose the desired product category and model.
您可以访问H3C网站（www.h3c.com）获取最新的产品配套资料：
1. 请访问网址：http://www.h3c.com/cn/Technical_Documents；
2. 选择产品类别和产品型号，即可查询和下载与该产品相关的手册。 Copyright © 2017, New H3C Technologies Co., Ltd.
For more information about the product and installation procedures, log in to www.h3c.com.hk
Copyright © 2017 新华三技术有限公司 版权所有，保留一切权利。
如需了解产品及安装方面的更多信息，请登录H3C网站 www.h3c.com