Hakko Electronics FT-8004 User manual

THERMAL WIRE STRIPPER
FT-8004
(with holder part)
●PACKING LIST AND PART NAMES
Please make sure that all items listed below are included in the package.
Thank you for purchasing HAKKO products.
When using the product, please read this manual
and follow the instruction to change the parts.
2019.5
MA03051XZ190508
HAKKO FT-8004 ...................................1
Holder part (for HAKKO FT-8004) .........1
SEMS screw P2 (M3×6) ........................2
Hexagon wrench (1.27mm) ...................1
Instruction Manual ................................1
Hexagon socket set screw (M2.5×2.5) ........2
PACKING LIST
Precautions Regarding Electrostatic Protection
CAUTION
This product includes features such as electrically conductive plastic parts and
grounding of the handle and station as measures to protect the device to be
soldered from the effects of static electricity.
Be sure to observe the following instructions:
⿟The handle and other plastic parts are not insulators, they are conductors. When
replacing parts or repairing, take sufcient care not to expose live electrical parts or
damage insulation materials.
⿟Be sure to ground the unit during use.
Handle
HAKKO FT-8004
Blade (not included)
Hexagon wrench
Hexagon socket set screw (×2)
Instruction Manual
Lead adjuster
THERMAL WIRE STRIPPER
FT-802
SEMS screw P2 (×2)
Holder part
(for HAKKO FT-8004)
OVERSEAS AFFILIATES
U.S.A.: AMERICAN HAKKO PRODUCTS, INC.
TEL: [phone] FAX: [phone]
Toll Free (800)88-HAKKO
4 2 5 5 6
http://www.hakkousa.com
HONG KONG: HAKKO DEVELOPMENT CO., LTD.
TEL: [phone] FAX: [phone]
http://www.hakko.com.cn
E-mail:[email protected]
SINGAPORE: HAKKO PRODUCTS PTE., LTD.
TEL: [phone] FAX: [phone]
http://www.hakko.com.sg
E-mail:[email protected]
Please access to the following address for the other Sales affiliates.
http://www.hakko.com
HEAD OFFICE
4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN
TEL:[phone] FAX:[phone]
http://www.hakko.com E-mail:[email protected]
© 2018-2019 HAKKO Corporation. All Rights Reserved.
Company and product names are trademarks or registered
trademarks of their respective companies.
WARNING
If output setting is over 70%, the handpiece and holder can be very hot. Please be
sure to turn on the auto-sleep function before use.
(On HAKKO FT-801, please be sure to connect the station and holder with included
connecting cable in order for auto-sleep to function properly.)
WARNING
Operating above 80% output setting can cause stress to the heating element and
shorten the life of the blades. Use 80% and above power only when necessary.
When not using the handle, be sure to place it in the holder.
CAUTION
Since the blades will become hot, place the handle on the handle holder when it is
not being used.

●How to attach the holder part (for HAKKO FT-8004)
Remove the holder part of the
handpiece holder inclusive with
HAKKO FT-801.
Attach the holder part inclusive
with HAKKO FT-8004.
●Removing the blades
Loosen and remove the hexagon socket set screw  xing the blades.
As illustrated below, pull the blade straight out.
●Attaching the lead adjuster
Handle
Attaching the lead adjuster
1 Remove the insulating cover from
the tip on the handle cover L-side
(the side with the HAKKO logo and
HAKKO FT-8004) and remove the
screw from the handle cover L-side.
2 Remove the handle cover L.
3 Align the lead adjuster mounting hole
with the handle cover L mounting
hole, replace the screw, and tighten
it lightly.
4 Firmly  t the nail of the root side of
the insulation cover in the handle
cover.
5 Attach the handle cover L to the
handle. Adjust the length of the lead
adjuster and  rmly tighten the screw.
NOTE:
Pay attention to the direction of the
blades when attaching the lead adjuster.
(See the following  gure.)
Attach the lead adjuster so that the
adjuster plate end is in parallel with the
blade surface.
The lead adjuster can be removed with
the handle cover attached to the handle.
Holder part Holder part
(for HAKKO FT-8004)
Lead adjuster
Handle cover L
Insulating cover
1
2
3
4
5
CAUTION
Please be sure to use the included holder part.
CAUTION
⿟When pulling out or inserting blades, be sure that the power is switched off.
⿟Before pulling out the blades, check that the blades have cooled down suf ciently.
Hexagon wrench
Hexagon socket set screw
(M2.5×2.5)
V groove
●Attaching the blades
Blades
Attaching blades
1 Stop provisionally in the tapped hole of
the handle, and do a set the hexagon
socket set screw.
2 Insert the blade so that the blade mounting
fl ange locks into the HAKKO FT-8004. Merge
type V and the V-groove of the back of the
blade.
NOTE:
Blades are not heated unless both blades are
inserted fully. Be sure to use the blades as a set.
3 Fix it with a  nger so that the point of a sword
does not work, tighten the hexagon socket
set screw with the hexagonal wrench to
secure the blades.