
1
Halco ProLED®Color-Changing LED Pool and Spa lamps offer a variety of microprocessor
controlled lighting effects that will instantly transform your pool or spa into a
color-rich paradise.
Halco ProLED
®
Color-Changing LED Replacement
Spa Lamps installation manual and operation guide for
following part numbers:
LLCS-120
and LLCS-12
The installation steps in this owner’s manual are intended as guidelines. For specic
instructions on how to replace a pool and spa lamp, please refer to the original
manufacturer’s pool light installation manual before proceeding.
This owner’s manual contains important information on installing and using your new
Halco ProLED® Color-Changing LED Pool or Spa lamp. Please read it carefully and keep
it in a safe place for future reference.
WARNING
Permanent damage to the low voltage 12VAC lamp will occur if installed on a 120VAC circuit.
WARNING
Remove warning label from Halco ProLED
®
Color-Changing lens before installation.
ATTENTION
A socket voltage range of 12.0 – 14.0 will achieve optimal brightness.
12V HALCO ProLED®COLOR-CHANGING OWNERS!
DANGER! RISK OF ELECTRICAL SHOCK OR ELECTROCUTION!
Always disconnect power to the pool light at the circuit breaker panel before attempting
to service the lamp. Failure to do so could result in serious injury or death due to
electrical shock. Refer to the original manufacturer’s pool light installation manual before
proceeding. As with any electrical device, installation and service should always be
performed by a qualied individual. This device is not intended for use in anything other
than in-ground pools and spas.
RATED LAMP LIFE
The illumination generated by Halco ProLED®Color-Changing and Spa lamps are
based on Light Emitting Diode (LED) technology. The average expected lamp life is
rated up to 50,000 elapsed time hours under normal operating conditions. [Pool Water
Temperature: 33°F to 97°F (1°C to 36°C)].
2
SAFETY PRECAUTIONS
• Do not open, service or tamper with any internal component of the Halco ProLED®
Color-Changing LED Pool or Spa lamp. Doing so will void the warranty. Follow each
instruction in this owner’s manual and pay careful attention to all warnings.
• Do not directly expose or immerse the Halco ProLED®Color-Changing LED Pool or
Spa lamp in water without containing it in a proper, watertight, NRTL (nationally
recognized testing laboratory) approved pool light housing and niche assembly.
• Keep the pool light housing dry.
•
Handle the Halco ProLED® Color-Changing LED Pool or Spa lamp with care. Be careful
not to drop the unit, or permanent damage can occur, which would void the warranty.
POOL & SPA LIGHT HOUSING COMPATIBILITY
LLCP-120, LLCP-12, LLCS-120, LLCS-12
Halco ProLED®Color Changing LED Pool and Spa lamps must be installed in a
compatible NRTL pool light housing. Compatible NRTL light housings include:
Pool Light Housings:
Hayward® Astrolite™ SP058 Series, Pentair® Amerlite 784 Series,
Swimquip 05086 Series, J&J Electronics TPL-P Series
Spa Light Housings: Hayward® Astrolite II SP059 Series, Pentair® SpaBrite™Series
Automation Systems.
Halco ProLED
®
Color-Changing
lamp integrates with most
pool automation systems*
* Operates effectively with Jandy
®
and Pentair
®
automation systems. Systems need to be
programmable to operate Pentair Intellibrite
®
5G LED Color.
IMPORTANT NOTE
READ THIS BEFORE ATTEMPTING INSTALLATION.
Pool Lamps installation manual and operation guide for
following part numbers: LLCP-120 and LLCP-12
Your
Halco ProLED®Color-Changing
lamp is not an ordinary light bulb. It is a valuable
electronic device that is not designed to come in direct contact with water. An improper
installation that results in water leakage into the light housing can permanently damage the
Halco ProLED®Color-Changing
lamp. Please read these installation steps and the original
manufacturer’s light installation manual carefully before proceeding.
Halco ProLED®Color-Changing
lamps are recommended for installation by a qualied
pool or spa professional.
Halco ProLED®Color-Changing
lamps cannot be used with
dimming systems. Doing so will void the warranty.
STEP 1
Remove light housing from niche
Make sure power to the light is turned off at the circuit breaker. Carefully remove the
existing light housing from the niche assembly and place it on the pool deck. There should
be enough power cord to do this easily. If there is not enough power cord to allow the light
housing to reach the pool deck surface, call your local pool service company.
DANGER! RISK OF ELECTRICAL SHOCK OR ELECTROCUTION!
Always disconnect power to the pool or spa light at the circuit breaker panel before
attempting to service the light. Failure to do so could resultin serious injury or death due
Project 33 - Halco ProLED Color-Changing LED Pool and Spa Lamp Install Guide_JJ16606_Packaged_050720.indd 2Project 33 - Halco ProLED Color-Changing LED Pool and Spa Lamp Install Guide_JJ16606_Packaged_050720.indd 2 5/12/20 11:31 AM5/12/20 11:31 AM