HAMPTON BAY Bryant User manual

Bryant
in Ceiling Fan
Owner’s Manual
Bryant
Ventilador de Techo de 1.17m
Manual del Propietario
46
823 338

Bryant by Hampton Bay

46 Bryant
Ceiling Fan by Hampton Bay
Date Purchased
Store Purchased
ETL Model No.
Serial No.
Vendor No.
UPC
Table of Contents
222875
Thank you for purchasing our ceiling fan. This product has been
manufactured with the highest standards of safety and quality.
845952000230
CF546KR
Safety Rules · · · · · · · · · ·
Unpacking Your Fan · · · · · · · ·
Installing Your Fan · · · · · · ·
Hanging Your Fan · · · · · · · ·
Making the Electrical Connections· ·
Finishing the Installation ·····
Attaching the Fan Blades ·····
Installing without the Light Kit ···
Operating Your Transmitter ····
Care of Your Fan ·········
Troubleshooting · · · · · · · · ·
Specifications · · · · · · · · · ·
1
2
3
4
5
6
7
8
9
10
10
11

Safety Rules - Read and Save These Instructions
WARNING
WARNING
To reduce the risk of electric shock, insure electricity has been
turned off at the circuit breaker or fuse box before beginning.
All wiring must be in accordance with the National Electrical
Code “ANSI/NFPA 70-1999” and local electrical codes. Electrical
installation should be performed by a qualified licensed
electrician.
WARNING: To reduce the risk of electrical shock or fire, do not
use this fan with any solid-state fan speed control device. It will
permanently damage the electronic circuitry.
CAUTION: To reduce the risk of personal injury, use only the
screws provided with the outlet box.
The outlet box and support structure must be securely mounted and
capable of reliably supporting a minimum of 35 pounds. Use only
UL Listed outlet boxes marked “FOR FAN SUPPORT”.
The fan must be mounted with a minimum of 7 feet clearance from
the trailing edge of the blades to the floor.
Avoid placing objects in path of the blades.
To avoid personal injury or damage to the fan and other items, be
cautious when working around or cleaning the fan.
Do not use water or detergents when cleaning the fan or fan blades.
A dry dust cloth or lightly dampened cloth will be suitable for most
cleaning.
1.
2.
3.
4.
5.
6.
7.
8.
9.
After making electrical connections, spliced conductors should be
turned upward and pushed carefully up into outlet box. The wires
should be spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the outlet box and
ungrounded conductor on the other side of the outlet box.
All set screws must be checked and retightened where necessary
before installation.
10.
11.
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE ARMS (ALSO REFERRED TO AS FLANGES), WHEN
INSTALLING THE BRACKETS, BALANCING THE BLADES OR
CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS IN –
BETWEEN ROTATING FAN BLADES.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR
FAN SUPPORT WITH THE SCREWS PROVIDED WITH THE OUTLET
BOX.
1

3
1
2
6
4
7
9
13
b
a
c
5
10
8
11
12
9. Switch box (1)
10.
11.
12.
Receiver (1)
Transmitter (1)
11A. Mounting plate for Remove Control
Balancing kit (1)
1.
2. Mounting bracket (1)
3. Canopy (1)
4. Canopy cover (1)
5. Ball/downrod assembly (1)
6. Coupling cover (1)
7. Fan motor assembly ( 1 )
8. Set of blades brackets (5)
Set of blades (5) (MDF blades)
WARNING
DO NOT INSTALL OR USE FAN
IF ANY PART IS DAMAGED OR MISSING.
CALL TOLL FREE 1-877-262-7511
13. Loose parts bag containing:
a . Blade attachment hardware (16 screws )
b. Mounting hardware (3 plastic wire
connectors)
c. Set of blade bracket hardware (11
screws)
d. Screw for remote control (2 PC)
Unpack your fan and check the contents. You should have the following items:
Unpacking Your Fan
2
11A
d

Installing Your Fan
WARNING
Outlet Box
Outlet Box
Outlet Box
Figure 2
Figure 1
Ceiling
Mounting
Plate
Provide Strong
Support
Recessed
Outlet Box
Figure 3
Figure 4
Tools Required
Mounting Options
Phillips screwdriver, straight slot
screwdriver, step ladder and wire cutters.
If there isn't an existing UL listed mounting
box, then read the following instructions.
Disconnect the power by removing fuses or
turning off circuit breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and
building materials. The outlet box and its
support must be able to fully support the
moving weight of the fan (at least 35 lbs). Do
not use plastic outlet boxes.
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT FAN
ONLY TO AN OULET BOX MARKED ACCEPT-
AB L E FO R FA N S U P P O RT A N D US E THE
MOUNTING SCREWS PROVIDED WITH THE
OULET BOX. OUTLET BOX COMMONLY USED
FOR THE SUPPORT OF LIGHTING FIXTURE MAY
NOT BE ACCEPTABLE FOR FAN SUPPORT AND
MAY NEED TO BE REPLACED. CONSULT A
QUALIFIED ELECTRICIAN IF IN DOUBT.
Figures 1~3 are examples of different ways to
mount the outlet box.
Note: You may need a longer downrod to
maintain proper blade clearance when
installing on a steep, sloped ceiling. The
maximum angle allowable is 18°. If the
canopy touches downrod, remove the
decorative canopy bottom cover and turn the
canopy 180° before attaching the canopy to
the mounting plate.
To hang your fan where there is an existing
fixture but no ceiling joist, you may need an
installation hanger bar as shown in Figure 4
(available at any Home Depot store).
3

Coupling
Cover
Motor Collar
Figure 9
Lead Wires
Ball/Downrod
Assembly
Canopy
REMEMBER to turn off the power. Follow the
steps below to hang your fan properly:
1.
3. Remove hanger ball from downrod assembly
by loosening set screw, removing the cross pin,
and sliding ball off rod.
(Figure 7)
4. Carefully feed fan wires up through the
downrod. (Figure 8) Thread the rod into the
coupling. Next, line up holes and replace lock
pin and hitch pin. Tighten set screws.
5. Slip coupling cover, canopy cover and
canopy onto downrod. (Figure 9) Carefully
reinstall hanger ball onto downrod, make sure
that cross pin is in correct position, set screws
are tighten and wires are not twisted.
Secure the mounting bracket to the
ceiling outlet box with the screws and
washers provided with your outlet box.
(Figure 5)
2. Loosen the two set screws from the
motor assembly. (Figure 6)
Remove the hitch pin
and lock pin from the downrod assembly.
6. Now lift motor assembly into position and place
hanger ball into mounting bracket. Rotate until the
check groove
should not rotate
if this is done correctly.
drops into the registration slot and
seats firmly. (Figure 10) Downrod
Figure 6
Downrod
Supply
wires
Figure 8 Figure 10
Registration
slot
Figure 5
Cross pin
Hanger
ball
Downrod
Figure 7
Outlet box
Mounting bracket
Hitch
pin
Lock
pin
Set
screws
4
Hitch
pin
Lock
pin
Hanging the Fan

Figure 12
Receiver
Mounting
bracket
WARNING: To avoid possible electrical
shock, be sure electricity is turned off at
the main fuse box before wiring.
NOTE: This remote control unit is
equipped with 16 code combinations to
prevent possible interference from or to
other remote units. The frequency
switches on your receiver and transmitter
have been preset at the factory. Please
recheck to make sure the switches on
transmitter and receiver are set to the
sa me posit ion, any com bina tion of
settings will operate the fan as long as the
transmitter and receiver are set to the
same position. (Figure 11)
Step 1. Insert the receiver into the
mounting bracket with the flat side of
the receiver facing the ceiling. (Figure
12)
Step 2. Motor to Receiver Electrical
Connections: Connect the black wire
from the fan to black wire marked "TO
MOTOR L". Connect the white wire
from the fan to the white wire marked
"TO MOTOR N" from the receiver.
Connect the blue wire
from the fan to the blue wire marked "For
Light" from the receiver. Secure the wire
connections with the plastic wire nuts
provided. (Figure 13)
Step 3. Receiver to House Supply Wires
Electrical Connections: Connect the
black (hot) wire from the ceiling to the
black wire marked "AC in L" from the
receiver. Connect the white (neutral) wire
from the ceiling to the white wire marked
"AC in N" from the Receiver. Secure the
wire connections with the plastic wire
nuts provided. (Figure 13)
St e p 4 . If your outlet box has a ground
wire (green or bare copper) connect it
to the fan ground wires; otherwise
connect the hanging bracket ground wire
to the mounting bracket. Secured the wire
connection with a plastic nut provided.
After connecting the wires spread them
apart so that the green and white wires are
on one side of the outlet box and black
and blue wires are on the other side.
Carefully tuck the wire connections up
into the outlet box. (Figure 13)
5
ON
Figure 11
Code switch
Rubber
cover
Making the Electrical Connections

Figure 14
Outlet box
Mounting
bracket
Canopy
Screw
Screw
Step 1. Tuck connections neatly into ceiling
outlet box.
Step 2. Remove one screw from the mounting
bracket and loosen the other screw
approximately 1/4.
Step 3. Align the canopy up to ceiling and over
the loosened screw. Place the canopy into key
hole and rotate canopy clockwise. (Figure
14)
Step 4. Secure the canopy by using
previous removed screw.
Step 5. Place the canopy over the canopy
and rotate canopy cover clockwise until
locked into right position.(Figure 14)
SUPPLY CIRCUIT
Ground
Conductor
Outlet Box
Green
Ground
Lead
Ground to
Downrod
BLACK
WHITE
WHITE
WHITE
WHITE
BLACK
BLACK
BLACK
BLUE
BLUE
GREEN
Figure 13
ON
Canopy Cover
WARNING
MAKE SURE TAB AT BOTTOM OF HANGER
BRACKET IS HANGER PROPERLY SEATED IN
GROOVE OF HANGER BALL BEFORE
ATTACHING CANOPY TO BRACKET. FAILURE TO
PROPERLY SEAT TAB IN GROOVE COULD CAUSE
DAMAGE TO ELECTRICAL WIRING.
6
Finishing the Installation

Step 1. A ttach the blades to the blade brackets
using the screws provided as shown in Figure
15. Start a screw into the blade bracket, but do
not tighten. Repeat for the 2 remaining screws
and washers.
Step 2. Tighten each screw securely. Make
sure the blade is straight.
Step 3. Use the 10 screws from the loose parts
b a g c o n t a i n i n g ( c ) . F a s t e n t h e bl a d e
assemblies to the motor (Figure 16) then
tighten the tw o s cr e w s t o e ac h b l a d e
assemblies (Figure 16A).
Touching
ceiling
Figure 17
The following procedure should correct most
fan wobble issues. Check after each step.
Step 1. Check that all blades and blade
bracket screws are secure.
(Please
refer to the introduction provide in the blade
balancing kit, which is individually packed.)
Step2 . M ost fan wobble problems are caused
when blade levels are unequal. Check this
level by selecting a point on the ceiling above
the tip of one of the blades. Measure this
distance as shown in Figure 17. Rotate the fan
un til th e next bl ade i s posi tio ned fo r
measurement. Repeat for each blade. The
distance should be equal within 1/8".
If all blade levels are not equal, you can adjust
the blade level with the following procedure.
Step 3. Use the enclosed Blade Balancing Kit
if the blade wobble is still noticeable.
Step 4. If the blade wobble is still noticeable,
interchanging two adjacent (side by side)
blades can redistribute the weight and
possibly result in smoother operation.
Figure 16
Motor assembly
Blade Bracket
Blade
bracket
Blade
Screws
Figure 15
Washer
Figure 16A
Blade Bracket
Screw
Motor Assembly
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY, DO
NOT BEND THE BLADE BRACKET WHILE
INSTALLING, BALANCING THE BLADES, OR
CLEANING THE FAN.
DO NOT INSERT FOREIGN OBJECTS BETWEEN
ROTATING FAN BLADES.
7
Attaching the Fan Blades