HAMPTON BAY GFS60014A User manual

USE AND CARE GUIDE
STEEL GAZEBO WITH HEAT TRANSFER FRAME
Item #
Model # GFS60014A
Questions, problems, missing parts? Before returning to the store,
call Hampton Bay Customer Service
8 a.m. - 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday
1-855-HD-HAMPTON
HAMPTONBAY.COM
THANK YOU
quality products designed to enhance your home. Visit us online to see our full line of products available for your home improv
lly create
ement needs.
Thank you for choosing Hampton Bay!

Table of Contents............................. . . ... . . . 2
Important Safety Instructions.................... . . ... . . 2
Warranty
We warrant the frame to be free of manufacturing defects tothe original purchaser for one year.
............. . . ............ . ..... . . . . . . . . . .
Pre-Assembly............................... . . ... . . . . .
Assembly. . . . . . .............................. . . ... . . . .
Planning Assembly ............................ . . . . . . .
Product Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 .
What is covered ........................... . . . . . . . . .
What is not covered ............ . . .............. . . . . .
Care and Cleaning ............................ . . . . . . . . .
Table of Contents
Important Safety Instructions
Package Contents . ......................... . . ... . . . . .
3
5
36
3
Hardware Included. . ......................... . . . . . . . . . 3
4
2
Warranty
CAUTION
This ga ebo was made for the explicit purpose of providing outdoor functions and is not to be used as a toy. This product is intended for
normal outdoor use; however, the manufacturer recommends storing and / or covering this gazebo when any formidable / severe weather
ames. Do not use this product as support. Do not shake, lean or climb on the product.
Children under the age of 10, near the product, should be supervised by a competent adult at all times. This product is NOT intended for
commercial use and will void the warranty.
1 YEAR LIMITED WARRANTY
!
!
CAUTION: When not in use, secure the product in a cool
and covered location.
WARNING:
WARNING: This gazebo unit is heavy, and may require twoThis gazebo unit is heavy, and may require two

Pre-Assembly
PLANNING ASSEMBLY
Read all instructions before assembly.
To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.
NOTE: More than one person may be required to assemble this product.
NOTE: Hardware not shown to actual size.
M6x15 Combination Bolt
M6x10 Combination Bolt
170+5
12+1
AA
BB
M6x20 Bolt 8+1 CC
Washer 4+1
DD
Nut Cap 4+1
EE
Part Description Quantity
AA BB CC DD EE
FF HH JJ KK GG
Stud 4+1
FF
Stake 8+1
GG
Hex Wrench 1
HH
Wrench 1
JJ
KK
Nut 4+1
3 HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
HARDWARE INCLUDED
NOTE: For safety, please use ladders and assemble on level ground.
8-Foot Ladder
(Qty. 2 recommended)

Pre-Assembly (continued)
PACKAGE CONTENTS
Part Description Quantity
Part Description Quantity

Assembly
1Attaching the Foot P Covers and the to the Post Legs
Insert the foot plate cover (B1) into the post leg (A) from the bottom.
Attach the post leg (A) to the foot p (B2) using M6x15 combination bolts (AA).
Fully tighten the bolts using the hex wrench (JJ).
Repeat this step for the other three post legs (A).
A
A
B2 B1
X4
AA
5
Please contact 1-855-HD-HAMPTON for further assistance
HAMPTONBAY.COM
e.

Assembly (continued)
2Inserting the Lining Ring Beam into the Long Side Left Beam and Long Side Right
Beam
Insert the lining ring beam (D) into the long side left beam (C1) and long side right beam (C2) using M6x15 combination bolts (AA).
Fully tighten the bolts using the hex wrench (JJ).
Repeat this step for the other long side left beam (C1) and long side right beam (C2).
AA
C1 AA
C2
D
C1
X2
C2
C1
6

Assembly (continued)
3Attaching the Beam Center Cover and the Middle Inclined Beam Connectors to
the Assembled Long Side Beam
Attach the beam center cover (E) to the middle of assembled long side beam (C1&C2), then attach the middle inclined beam
Attach the middle inclined beam connector (F) to the long side left beam (C1) directly using M6x15 combination bolts (AA).
Attach the middle inclined beam connector (F) to the long side right beam (C2) directly using M6x15 combination bolts (AA).
Fully tighten the bolts using the hex wrench (JJ).
Repeat above steps for the other assembled long side beam (C1&C2).
NOTE: The middle inclined beam connectors (F) should face the hole side of long side beam (C1&C2).
7
Please contact 1-855-HD-HAMPTON for further assistance
HAMPTONBAY.COM
C2
C1
F
E
F
C1 AA
E
C2
E
e.
connector (F) to the beam center cover (E), align the hole and secure with M6x15 combination bolts (AA) as shown below.

Assembly (continued)
4Attaching the Assembled Long Side Beam to the Post Legs
Attach the assembled long side beam (C1&C2) to the two post legs (A) using M6x15 combination bolts (AA).
Fully tighten the bolts using the hex wrench (JJ).
Repeat this step for the other two post legs (A).
C1&C2
AA
A
A
A
X2
C1
C2
8

Assembly (continued)
5Inserting the Lining Ring Beam into the Short Side Left Beam and Short Side
Right Beam
Insert the lining ring beam (D) into the short side left beam (G1) and short side right beam (G2) using M6x15 combination bolts (AA).
Fully tighten the bolts using the hex wrench (JJ).
Repeat this step for the other short side left beam (G1) and short side right beam (G2).
G1 G2
G1 AA
AA
G1 DG2
X2
9
Please contact 1-855-HD-HAMPTON for further assistance
HAMPTONBAY.COM
e.

Assembly (continued)
6Attaching the Triangular Support Pipe to the Assembled Short Side Beam
Attach the triangular support pipe (H) to the assembled short side beam (G1&G2) using M6x15 combination bolts (AA), as shown below.
Fully tighten the bolts using the hex wrench (JJ).
Repeat this step for the other triangular support pipe (H).
NOTE: The triangular support (H) should insert from the side of the assembled short side
beam (G1&G2) without hole to the side with hole.
10
G1
H
G2
AA
Inside
H
G2
G1

Assembly (continued)
7Attaching the Oblique Beams to the Assembled Short Side Beam and
Triangular Support Pipe
Attach the oblique left beam (J1) and the oblique right beam (J2) to the assembled short side beams (G1&G2) and triangular
support pipe (H) using M6x15 combination bolts (AA).
Fully tighten the bolts using the hex wrench (JJ).
Repeat this step for another oblique left beam (J1) and the oblique right beam (J2).
NOTE: The front of the oblique beams (J1&J2) should be aligned with the front of short side beams (G1&G2).
J1
H
J2
G2
G1
J1&J2
J1 J2
G1&G2
H
AA
11
Please contact 1-855-HD-HAMPTON for further assistance
HAMPTONBAY.COM
e.

Assembly (continued)
8Connecting the Assembled Short Side Beams to the Assembled Long Side Beams
and Post Legs
C2
C1
C1 C2
G1
G2
G1&G2
Attach the assembled short side beams (G1&G2) to the assembled long side beams (C1&C2) using M6x15 combination bolts (AA),
as shown below.
Fully tighten the bolts using the hex wrench (JJ).
C1&C2
G1&G2
C1&C2
AA
12

Assembly (continued)
9Connecting the Other Assembled Short Side Beams to the Assembled Long
Side Beams and Post Legs
AA
Attach the other assembled short side beams (G1&G2) to the assembled long side beams (C1&C2) using M6x15 combination bolts
(AA), as shown below.
Fully tighten the bolts using the hex wrench (JJ).
G1&G2
C1&C2
G2
G1
C2
C1
C1
G2
G1
C2
13
Please contact 1-855-HD-HAMPTON for further assistance
HAMPTONBAY.COM
e.

Assembly (continued)
10 Attaching the Corbels to the Beams and the Post Legs
Attach four corbels (K) to the assembled long side beams (C1&C2) and post legs (A) using M6x15 combination bolts (AA).
Attach the other four corbels (K) to the assembled short side beams (G1&G2) and post legs (A) using M6x15 combination bolts (AA).
Fully tighten the bolts using the hex wrench (JJ).
A
A
AA
C1&C2
G1&G2
C1&C2G1&G2
K
AA G2
K
K
K
K
K
G1
C2
C2
C1
C1
G1
G2
X8
14

Assembly (continued)
11 Attaching the Crossbeam Support Brackets to the Long Side Beams and the Short
Side Beams
Attach the crossbeam support brackets (L) to the assembled long side beam (C1&C2) and the short side beam (G1&G2) using
M6x15 combination bolts (AA).
Fully tighten the bolts using the hex wrench (JJ).
AA
G1&G2 L
C1&C2
G2
G1 L
L
G1
G2
C2
C1
C2
L
L
C1
X4
15
Please contact 1-855-HD-HAMPTON for further assistance
HAMPTONBAY.COM
e.

Assembly (continued)
12 Attaching the Studs to the Top Beam
Screw the studs (GG) to the top beam (M), as shown below.
Repeat this step for the other top beam (M).
NOTE: Pay attention to tighten the correct holes.
GG
M
GG
M
16

Assembly (continued)
13 Inserting Lining Ring Beam into the Top Beams
Insert the lining ring beam (D) into two top beams (M) using M6x15 combination bolts (AA), as shown below.
Fully tighten the bolts using the hex wrench (JJ).
M
D
AA AA
M
17
Please contact 1-855-HD-HAMPTON for further assistance
HAMPTONBAY.COM
e.

Assembly (continued)
14 Attaching the Roof Panel Connectors to the Top Beams
Attach the roof panel connector 1 (N1) and roof panel connector 2 (N2) to the top beams (M) using M6x20 countersunk bolts (CC),
as shown below.
Fully tighten the bolts using the hex wrench (JJ).
N1
N2
M
CC
M
N1
M
N2
18

Assembly (continued)
15 Attaching the Chandelier Hooks to the Top Beams
Screw the chandelier hooks (U) clockwise to the top beams (M), as shown below.
U
M
M
U
19
Please contact 1-855-HD-HAMPTON for further assistance
HAMPTONBAY.COM
e.

Assembly (continued)
16 Inserting the Top Beams to the Oblique Beams and Attaching the Top Beam
Plates to the Oblique Beams and Top Beams
Insert the assembled top beams (M) to the oblique left beams (J1) and oblique right beams (J2), as shown below.
Attach the top beam plates (O) to the top beams (M) and the oblique beams (J1&J2), align the holes and secure with M6x15
combination bolts (AA).
Fully tighten the bolts using the hex wrench (JJ).
O
AA
O
J2
M
J1
J2
O
J1
M
J2
OJ1
M
J2
20