Hans Grohe Sportive 31755000 User manual

UNIDOMO®
www.unidomo.de
04621- 30 60 89 0
[email protected]
Mo.-Fr. 8:00-17:00 Uhr
a member of DAIKIN group
  
 
  

Installation Instructions
Avista
Bath & Shower Set
31756000
Status
Bath & Shower Set
31757000
Sportive²
Bath & Shower Set
31755000

2
Contents
Safety and Important Information 3
Pack Contents 4-5
Dimensions 6
Technical Data 7
Installation Requirements 8-9
Installation
Bath & Shower Mixer 10-11
Porter´C / Porter´S 12-13
Adjustement
Hot Water Limiter Adjustment 14
Operating your Shower 15
Cleaning 15
Spare Parts 16-19
Trouble Shooting 20
Warranty 20
If there are any queries regarding this product or its
installation, please contact the Hansgrohe technical
hotline: [phone]

3
Safety and Important Information
Hansgrohe products are safe provided they are installed, used and maintained in accordance with these
instructions and recornrnendations.
Please read these instructions thoroughly and retain for future use.
The plumbing installation of this shower must comply with the requirements of UK
Water Regulations/Bylaws (Scotland), Building Regulations or any other regulations specified by the local
Water Authority and supplier.
We strongly recommend that you use a plumber registered with or a member of an Association:
Institute of Plumbing (IOP) - throughout the UK
National Association of Plumbing, Heating and Mechanical Services Contractors
(NAPH & MSC) - England & Wales
Water Industry Approved Plumber Scheme (WIAPS)
Dispose of plastic bags carefully
Keep children well away from the work area.
Check for hidden pipes and cables in the wall before drilling holes.
The unit must be mounted on a finished waterproofed wall surface (usually tiles).
If you are using power tools (e.g. to drill holes) wear safety glasses and always disconnect tools from the
power supply after use.
Do not operate the shower unit if the hand shower or spray hose has been damaged or is blocked.
Do not block the flow of water from the hand shower, by placing it on your hand or any other part of your
body or foreign object.
The bath & shower mixer unit should be serviced annually by a qualified person to ensure maximum safety
during use.
The mixer incorporates check valves (page 16 pos. 10 / page 17 pos. 10 / page 18 pos. 12).
The fitting of isolation valves is required (preferred location page 8 and 9 Installation Requirements)

4
Please check that you have been supplied with the
following:
1
2
3
4
5
6
8
7
1
2
3
4
1
2
3
4
Avista Bath & Shower Set
1 Bath-shower mixer
2 Fibre washers
3 Escutcheons
4 S-unions
Sportive² Bath & Shower Set
1 Bath-shower mixer
2 Fibre washers
3 Escutcheons
4 S-unions
Status Bath & Shower Set
1 Bath-shower mixer
2 Fibre washers
3 Escutcheons
4 S-unions
Pack Contents
Sportive² / Avista /Status
5 Pillar unions
6 Large seals
7 Fixing nuts
8 Fibre washers

5
Porter S
1 Hand shower cursor
2 Washers
3 Fixing screws
4 Wall plugs
Hand Shower & Hoses
1 Hose Marin
2 Hose Verso
3 Status hand shower
4 Sportive² hand shower
5 Avista hand shower
6 Mesh washer
1
3
5
4
6
1
2
3
42
Porter Club
1 Hand shower cursor
2 Fixing screws
3 Wall plugs
2
3
1

6
Dimensions
Sportive² Bath & Shower Mixer
Avista Bath & Shower Mixer
Sportive² Bath & Shower Mixer
with pillar union
Avista Bath & Shower Mixer
with pillar union

7
Technical Data
Sportive² / Avista /Status
Bath & Shower Set
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
Hot water temperature: max. 80° C
Recommended hot water temp.: 65° C
Centre distance: 150 ± 12 mm
Connections G ½: cold right - hot left
Rate of flow 0,3 MPa: approx. 22 l/min
(1 MPa = 10 bar = 147 PSI)
Anti-pollution function
Hot water connection: Left hand
Cold water connection: Right hand
Minimum difference between hot
water and mixed water temperature: 6 K
Hot and cold supply pressure should be balanced
Wall Bar, Hand Shower & Hose
Status Bath & Shower Mixer Status Bath & Shower Mixer
with pillar union

8
Installation Requirements
This mixer valve must be installed in compliance with
current Water Regulations. If you have any doubts
about the Water Regulation requirements contact
your local water services provider or use the services
of a professional plumber.
This mixer valve is suitable for use with the following
water supply systems:
Gas Combination Boiler (multi-point) 1.0 - 10 bar*
Unvented System (pressure balanced) 1.0 - 10 bar
Pumped System 1.0 - 10 bar
Before connecting the mixer, water should be flushed
through the system to remove all debris that might
otherwise damage the valve.
* If pressure is in excess of 3.5 bar, a pressure-
reducing valve should be fitted.
KEY
Isolating valve
Reducing valve
Mixer Valve
Pump
Gas Combination Boiler (multi-point)
Unvented System (pressure balanced)

9
Pumped System

10
4Bath/Shower Mixer with pillar union
180 mm
Installation
12
32 - 41
mm
Seal
Bath/Shower Mixer
PTFE
tape
3
150 mm
HOT
COLD
max. 25 mm

11
Bath/Shower Mixer with pillar union
Two options
a. As the shower mixer above (positioned over a
bath).
b. Fitting to the bath using the supplied pillar uni-
ons.
1. The pillar unions are designed to fit tap holes
on a bath 180mm apart with hot on the left and
cold on the right (fig.4).
2. Flush through the hot and cold water supplies.
3. Place fibre washers into the holes of the chrome
union nuts. (DO NOT USE FILTERS WHEN
USING PILLAR UNIONS!)
From under the bath fit a large seal washer over
the thread then fix with the nuts.
4. Fasten the mixer onto the union pillars using the
union nuts (be careful not to damage the chrome
finish).
Bath/Shower Mixer
1. The hot and cold water outlets should be 150mm
apart (plus or minus 12mm). Hot on the left and
cold on the right (fig. 1). The recommended
plumbing fittings are ½“ back plate elbows (not
supplied).
2. Flush through the hot and cold water supplies.
3. Wrap PTFE tape round the S-unions and screw
into the backplate elbows. The S-unions must
protrude beyond the tiled surface between 32
and 41mm (figs.2-3).
4. Seal the gap between the S-unions and the tiles
(fig.3).
5. Screw the escutcheons onto the S-unions.
6. Fasten the mixer onto the S-unions using the
union nuts. Align the unit and tighten the nuts
(be careful not to damage the chrome finish). The
S-unions allow inaccuracies to be compensated
for.

12
2
1b1a
Installation

13
1. Measure the desired space for the fixation points
of the wall support. Adjust the dimensions to the
tile pattern if required (fig. 1).
2. Using a centre punch mark the hole positions
and using a 6mm suitable drill bit drill a hole to
a depth of 45mm (fig.1).
Handy Hint: Mark the drill hole positions on a pi-
ece of masking tape on the wall. The drill bit will
be less likely to slip when you start drilling.
3. Insert wall plugs into the holes (beyond the depth
of the supports) and seal around the hole. Fix the
porter in position using the 50mm fixing screws
and washers. (fig. 1).
4. Attach the hose to the hand shower head ensu-
ring a mesh washer is inserted (where shown)
to protect against any incoming dirt. Attach
the other end of the hose to the connection on
the mixer ensuring a rubber washer is inserted
where shown.
Place the hand shower into the hand shower
slider (fig.2).
Where the contractor mounts the product,
he should ensure that the entire area of
the wall to which the mounting plate is to
be fitted, is flat (no projecting joints or tiles
sticking out), that the structure of the wall
is suitable for the installation of the prod-
uct and has no weak points. The delivered
mountig kit is suitable for:
• Concrete
• Natural stone with dense structure
• Solid brick
• Sand-lime solid brick
• Solid pumice bricks
• Aircrete
• Porous bricks
• Vertically perforated brick
• Sand-lime perforated block
• Hollow block made from lightweight concrete
• Solid panel made from gypsum
• Standard gypsum wallboard / plaster fiber board
• Chipboard
Suitable fixing material must be used at
other wall constructions!

14
Hot Water Limiter Adjustment
Hot water temperature 60°C, cold water temperature 10°C, flow rate 0,3 MPa.
21 3
4 5
6 7

15
Operating your Shower
The mixer is actuated by lifting the lever head.
Swivel to the left = hot water (fig. 1),
swivel to the right = cold water (fig. 2).
The flow is changed from bath to shower function by
pulling the knop at the upper side of the spout
(fig. 3). After shutting off the water flow, the mixer
returns automatically to the bath function (fig. 4).
Cleaning
Cleaning materials for Mixers and
Showers
Acids are necessary ingredients of cleaning materi-
als for removing lime. However please pay particu-
lar attention to the following points when cleaning
mixers and showers:
Only use cleaning material specifically intended
for this type of cleaning - such as Hansgrohe’s
Decalcifying Agent, available through the spe-
cialist sanitary trade.
Never use cleaning materials which contain
hydrochloric, formic or acetic acid, as they
cause considerable damage.
Never use Phosphoric acid as it can cause
damage.
Never mix any cleaning material with another.
Never use cleaning materials on appliances with
an abrasive effect, such as unsuitable cleaning
powders, sponge pads or micro fibre cloths.
Cleaning Instructions for Mixers and
Showers
Please follow the cleaning materials manufacturer’s
inistructions. In addition pay attention to tlie fol-
lowing points:
Clean the mixers and showers as and when
required.
The cleaning dosage and time the cleaner needs
to take effect should be adjusted according to
the product and the cleaner should not be left
longer than necessary.
Regular cleaning can prevent calcification.
When using spray cleaner, spray first into a
cloth or sponge never directly onto the sanitary
tapware, as drops could enter openings and
gaps and cause damage.
After cleaning, rinse thoroughly with clean water
to revove any cleaner residue.
Important
Residues of liquid soaps, shampoos and shower
foams can also cause damage, so rinse with clean
water after use.
If the surface is already damaged, the effect of
cleaning materials will cause further damage.
Damage caused by improper treatment will
not be covered by our guarantee.
1
2
3
4

16
Spare Parts
Sportive² Bath & Shower Set
1 handle 14897000
1.1 screw cover 96338000
2 flange 97406000
3 nut 97209000
4 cartridge cpl. 92730000
5 escutcheon 94135000
6 S - unions (2) 94140000
7 aerator cpl. 13956000
8 selector 94077000
9 diverter knob 94078000
10 non return valve DW 15 (2) 94074000
11 noise reduction (2) 96429000
12 locking screw for handle 96059000
13 pillar unions (2) 98838000
7
5
10
9
8
4
3
2
1.1
1
6
11 12
13

17
Spare Parts
Avista Bath & Shower Set
2
3
4
9
87
5
10
1
1.1
6
11
12
1 handle 31792000
1.1 screw cover 96338000
2 flange 96656000
3 nut 96690000
4 cartridge cpl. 92730000
5 flange 94135000
6 S-unions (2) 94140000
7 aerator cpl. 13956000
8 selector assy 94077000
9 diverter knob 94078000
10 non return valve DW 15 (2) 94074000
11 noise reduction (2) 96429000
12 locking screw for handle 96059000
13 pillar unions (2) 98838000
3
13

18
1
1.1
3
2
4
5
6
9
10
12
7
8
11
Spare Parts
Status Bath & Shower Set
Spare parts
1 handle 32097000
1.1 screw cover 96338000
2 flange 96656000
3 nut 96690000
4 cartridge, assy 92730000
5 locking screw for handle 96059000
6 escutcheon Ø 68 mm 96467000
7 S - unions (2) 94140000
8 noise reduction (2) 96429000
9 aerator cpl. 13956000
10 selector assy 94077000
11 diverter knob 96466000
12 non return valve DW 15 (2) 94074000
13 pillar unions (2) 98838000
13

19
Spare Parts
Porter´S, Porter Club,
Hand Shower & Hose
1 Hose Avista 28268002
2 Hose Sportive² / Status 28275000
3 Hand shower Status 28778000
4 Hand shower Sportive² 28779000
5 Hand shower Avista 28359000
6 Porter´S Sportive² / Status 28331000
7 Porter Club Avista 27521000
7
1
2
3
4
5
6