Hans Grohe Croma 160 Showerpipe 27244000 Manual

Croma 160 Showerpipe
27244000
ZH 用户手册/组装说明 2
EN Instructions for use / assembly instructions 3

2
安装 参见第页 4
选装附件
(不在供货范围内)
匹配瓷砖的圆盘镀铬#95163000(参
见第页6)
清洗
(参见第页10)
流量示意图 (参见第页14)
手持花洒
顶置花洒
大小
(参见第页14)
操作(参见第页8)
请在使用喷头后略微倾斜，排空其中
水分。
备用零件
(参见第页15)
请勿使用含有乙酸的硅胶！
符号说明
技术参数
工作压强： 最大0,6MPa
推荐工作压强： 0,1-0,4MPa
测试压强： 1,6MPa
(1MPa=10bar=147PSI)
热水温度： 60°C
热力消毒: 最大70°C/4分钟
• 自动防止回流
• 该产品专为饮用水设计！
安全技巧
装配时为避免挤压和切割受伤，必须戴上手
套。
头顶花洒夹持杆只为夹持头顶花洒而设计，不
得让其承载其它物品！
不得让儿童和肢体、精神和/或意识有障碍的成
人在不受监管的情况下使用淋浴系统。受酒精
或毒品影响的人员不得使用淋浴系统。
必须避免让身体敏感部位（如眼睛）接触到莲
蓬头喷水。必须保持莲蓬头与人头之间有足够
的距离。
该产品不得作扶柄使用。必须安装单独的扶
柄。
本产品只允许作为洗浴、卫生和洁身之用。
安装提示
• 安装前必须检查产品是否受到运输损害。安装
后将不认可运输损害或表面损伤。
• 管道和阀门必须根据通用标准进行安装、冲洗
和检查。
• 请遵守当地国家现行的安装规定。
• 本安装说明中所规定的安装尺寸理想用于身高
1700mm左右的人士。尺寸可根据需要进行修
改。在这种情况下，您必须留意，如果安装高度
改变，则花洒到地板的最小高度也随之改变，且
必须考虑到连接尺寸的改变。
• 由有资格的专业人员进行产品安装时请注意：在
所有加固区域中，加固表面是否平整（无突出的
接缝或瓷砖），墙体结构是否适合产品安装且未
显露出任何缺点。
• 必须使用预装配好的过滤器芯，以保障手持花
洒达到标准水流量并避免从管网中冲出污物。
污物可损害功能和/或导致损坏手持花洒的功能
件，对由此所产生的损害汉斯格雅公司将不承
担责任。
• 紧急情况下,可使用细的锯子将下方区域中阀门
与头顶莲蓬头之间的管子锯短。
• 该花洒仅允许连接在卫浴龙头或截止阀之后。
中文

3
Assembly see page 4
Special accessories
(order as an extra)
tile-matching-disk chrome plated
#95163000 (see page 6)
Cleaning
(see page 10)
Flow diagram (see page 14)
 Hand shower
 overhead shower
Dimensions
(see page 14)
Operation(see page 8)
To empty the overhead shower after use,
hold it in a slightly inclined position.
Spare parts
(see page 15)
Do not use silicone containing acetic acid!
Symbol description
• If required, the bottom part of the pipe between the
fixture and the shower head can be shortened with a
fine-toothed saw.
• The shower may only be connected downstream of a
shut-off valve or sanitary fitting.
Technical Data
Operating pressure: max. 0,6 MPa
Recommended operating pressure: 0,1 - 0,4 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: 60°C
Thermal disinfection: max. 70°C / 4 min
• Safety against backflow
• The product is exclusively designed for drinking water!
Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The arm of the shower head is intended only to hold
the shower head. Do not load it down with other
objects!
Children as well as adults with physical, mental and/
or sensoric impairments must not use this product
without proper supervision. Persons under the influ-
ence of alcohol or drugs are prohibited from using
this product.
Do not allow the streams of the shower touch sensi-
tive body parts (such as your eyes). An adequate
distance must be kept between the shower and you.
The product may not be used as a holding handle. A
separate handle must be installed.
The product may only be used for bathing, hygienic
and body cleaning purposes.
Installation Instructions
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• The pipes and the fixture must be installed, flushed
and tested as per the applicable standards.
• The plumbing codes applicable in the respective
countries must be observed.
• The installation dimensions stated in these installation
instructions are ideal for people of approximately
1700 mm in body height. The dimensions can be al-
tered if required. In this case, pay attention to the fact
that a change of installation height will also change
the minimum height, and that the altered mounting
dimensions must be taken into consideration.
• During installation of the product by qualified trained
personnel, make sure that the entire fastening surface
is even and smooth (no protruding seams or tile
offset), that the finish of the wall is suitable to apply the
product and has no weak points.
• The premounted filter insert must be used to ensure
a normal flow of the shower and to prevent dirt from
entering through the pipes. Dirt entering can affect the
function and/or lead to damages to the shower. Hans-
grohe will not be held liable for this type of damage.
English

4
1 2
900 mm
3
1.
Ø 6 mm
Ø 6 mm
2.
4
SW 8 mm

5
1.
2.
SW 3 mm 3.
SW 3 mm
(2 Nm)
7
max. 875 mm
1.
Ø 6 mm
2.
8
3.
5 6

6
11
Silicone
9a
10
1.
2.
2.
Silicone
9b
95163000
3.
Nr. 10476220
Armaturenfett
Grease
1.
12
94246000
SW 17 mm
(10 Nm)
13

7
94246000
15b
14 15a

8

9
1
2a 2b
1.
2.

10
表面损坏的部件必须更换，否则会有受伤
的危险。
不按规定进行清洁而造成的任何损坏不在本公司产
品保修范围之内。
QuickClean
有了QuickClean，手工清洁功能，要去掉喷头上的
水垢，只需简单地搓除即可。
担保
Hansgrohe向用户保证，该产品无制造缺陷。如果
自购买之日起五年内出现缺陷，Hansgrohe将免费
排除。保证条件和详情见www.hansgrohe-int.com/
guarantee。在提出保修的权利时请联系您的合同
方。本保证不涉及有关国家法律规定的消费权
汉斯格雅产品的清洁建议
现代的卫浴龙头、厨房龙头、花洒、配件、盥洗
台、浴盆和加热器采用的制造材料非常迥异，以适
应产品外形设计和使用功能的市场需求。
为了避免产品损坏和由此引发的投诉及争议，必须
在使用和清洁产品时遵循有关规程。
在保养汉斯格雅产品时，原则上必须注意：
• 只能使用那些有明确注明是适用于本产品的清
洁剂。
• 不允许使用含有盐酸、蚁酸、氯漂或醋酸的清
洁剂，因为这些清洁剂会给产品表面造成严重的
损伤。
• 含磷酸的清洁剂必须在特定条件下使用。
• 不允许将两种以上清洁剂混合使用。
• 不允许使用具有研磨作用的清洁工具和设备，如
不适合的清洁粉末、海绵垫或超细麦克布。
• 必须严格遵守清洁剂生产厂商的使用说明。
• 严格遵守清洁剂的用量和作用时间，决不允许清
洁剂的作用时间长于规定值。
• 定期的清洁以预防水垢。
• 不允许将清洁剂直接喷射到汉斯格雅产品上，因
为喷雾会进入汉斯格雅产品的开口部分和缝隙中
而造成损害。首先将清洁剂喷在软布上，再用软
布进行清洁。
• 清洁之后必须用足够的清水冲洗，以彻底去除残
留的吸附物（清洁剂）。
• 不允许使用蒸汽清洗机，高温会损害产品。
重要说明
肥皂，洗发水、沐浴液、染发剂、香水、刮胡水、
指甲油的残留也会对产品造成损伤。
此处：使用后要小心地用清水将剩余物冲洗干净。
同样在产品下方不得存放洗涤剂和化学药品，例如
不可放在用于洗脸盆的梳洗柜中否则挥发气体将
损坏产品。
在已经损伤的表面继续使用清洁剂会给表面造成更
大的损伤。
中文
QUICK
CLEAN

11
Components with damaged surfaces
must be exchanged, otherwise there
could be an injury danger.
Damage caused by improper treatment will not be
covered by our guarantee.
QuickClean
The QuickClean cleaning function only needs a small
manual rub over to remove the lime scale from the spray
channels.
Warranty
Hansgrohe guarantees to the consumer that this product is free
of production faults. If evertheless any defect is detected within
5 years from date of purchase, Hansgrohe will remedy this
defect free of charge. You will find the conditions and details
of this guarantee at www.hansgrohe-int.com/guarantee.
Please contact your contracting party to claim your rights
under this guarantee. This guarantee does not affect the
customer‘s rights under the respective national legislation.
Cleaning Recommendation for
Hansgrohe Products
Today, modern sanitary and kitchen tapware, showers,
accessories, washstands, tubs and radiators consist of
very different materials to comply with the needs of the
market with regard to design and functionality.
To avoid damage and reclamations, it is necessary to
consider certain criteria when cleaning.
With regard to caring for the
Hansgrohe products, the following
must in principle be heeded:
• Only use cleaning material which is explicitly provided
for this type of application.
• Never use cleaning materials, which contain
hydrochloric acid, formic acid, chlorine pale lye or
acetic acid, as they cause considerable damage.
• Phosphorus acidic cleaners are only conditionally applicable.
• Mixing cleaning agents is not permitted, generally.
• Never use cleaning materials or appliances with an
abrasive effect, such as unsuitable cleaning powders,
sponge pads or micro fibre cloths.
• The instructions of the cleaning agent manufacturers
have to be followed absolutely.
• Cleaning has to be carried out with a specified cleaner
dosage, contact time, object-related and adapted to the needs.
• The building up of calcifications has to be removed by
cleaning regulary.
• When using spray cleaners, spray the cleaning solution onto
a soft cloth or sponge, never directly onto the Hansgrohe
products, as the atomised spray could enter openings and
gaps in the Hansgrohe products and cause damage.
• After cleaning rinse thoroughly with clean water to
remove any cleaner residue.
• The use of steam cleaners is not permitted. The high
temperatures can damage the products.
Important
Residues of toiletries such as liquid soaps, shampoos and
shower gels, hair dyes, perfumes, aftershave and nail
varnish can also cause damage.
Here too: Carefully rinse with water after use to remove residues.
Likewise, do not store any cleaning agents or chemicals
under the products, for example in a vanity unit, as the
vapours may damage the products.
The damage of already damaged surfaces will
deteriorate under the effect of the cleansers.
English
QUICK
CLEAN

12
Reinigung
max. 10 min
20 mm
43
> 1 min
5
1 2
94246000

13
93339000
94246000
Reinigung
3 4
> 1 min
5
1 2
6

14
900 1000800
19181918 2018201818181818 min. 25min. 25
2020 21201920
18201820 1920192017201720
100°
G 1/2
1018
725 - 875
50 83
235
bar
4,5
0,0
0,5
1,0
1,5
2,0
2,5
3,0
3,5
4,0
5,0
0,45
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,50
5,50,55
6,00,60
036912 15 18 21 24 27 30
MPa
00,1 0,2 0,3 0,4 0,5
Q = l/min
Q = l/sec
2
1
80°
80°

15
Croma 160 Showerpipe
27244000
95406000
95405000
95401000
94246000
95659000
28450000
96179000
95160000
98716000
95687000 95689000
98131000
(15x2,5)
98382000
(12x2,25)
94246000
93339000
95404000
98913000
94184000
95441000
98168000
(41x1,5)
96526000
(M6x10)
98129000
(14x2)
96044000
98058000
96044000
98058000
28276000
28278000
28537007
96179000
95163000

16 Hansgrohe · Auestraße 5 - 9 · D-77761 Schiltach · Telefon [phone] · Telefax +49 (0) 7836/511440
E-Mail: [email protected] · Internet: www.hansgrohe.com 03/2018 9.02294.06
Prüfzeichen