Hanskamp PowerSpray User manual

PowerSpray
EN
Installaon and operang instrucons
Arcle number: 010-271-000
Date: november 2016
Version 1.1– Translaon of original manual
According to Annex 1 chapter 1.7.4 Machine Guideline 2006/42/EC
Doenchem,
The Netherlands
www.hanskamp.nl/en
039-011-000 up to 039-366-000
Vernevelsysteem voor vloeistoffen
Liquids spraying system
Zerstäubungssystem für Flüssigkeiten
Vaporisateur de liquides
&

2 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
Preface
Manual Contents
This manual contains the informaon necessary for the correct installaon and operaon
of a Hanskamp PowerSpray (g. 1 & 2). Study and understand this informaon thor-
oughly before conguraon of the PowerSpray. Failure to do so could result in damage
to equipment. Please consult your milking equipment dealer if you do not understand
the informaon in this manual, or if you need addional informaon.
All informaon in this manual has been compiled with care. Hanskamp shall not be liable
for errors or faults in this manual. The recommendaons are meant to serve as guide-
lines. All instrucons, pictures and specicaons in this manual are based on the latest
informaon that was available at the me of publicaon. Your PowerSpray may comprise
improvements, features or opons that are not covered in this manual.
Toepasselijkheid
The table below shows the type numbers of the PowerSpray for which this manual is
applicable. The type number can vary, according to the type of control of the Power-
Spray, the number of liquid types, as well as the number of feeding staons/milking ro-
bots in which the liquid has to be sprayed. In the table below, the type number variaon
is indicated with the leer A, B en C, respecvely.
Model designaon
Contact number Local Service Provider
We suggest you write the name, address and telephone number of your local service
provider contact in the table below. This makes sure you can easily nd the informaon.
Model Type number Control type
(A)
Number of liquid types
to be sprayed (B)
Number of spray
locaons (C)
PowerSpray 039-ABC-000
0: Direct 0: No PS PompUnit
1: Nedap, GEA, DM, Manus 1: 1x PS PompUnit 1: 1x PS SprayUnit
2: DeLaval, SAC, Fullwood 2: 2x PS PompUnit 2: 2x PS SprayUnit
3: Lely A4 3: 3x PS PompUnit 3: 3x PS SprayUnit
4: 4x PS PompUnit 4: 4x PS SprayUnit
5: 5x PS PompUnit 5: 5x PS SprayUnit
6: 6x PS PompUnit 6: 6x PS SprayUnit
Naam
Adres
Telefoonnummer
E-mail adres
1
2

3 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
1. Introducon
Having a healthy herd is the key for a successful dairy farm. A good animal health is how-
ever always the case, especially when a lot is asked from an animal. Is this case, sup-
porng measures are necessary, preferably without too much labour, and without a high
amount of costly anbiocs.
The PowerSpray of Hanskamp oers the perfect soluon for this situaon. It consists of
a so called PompUnit and a SprayUnit. With this, various soluble addives or medicines
can be sprayed over the nose of the cow, and in this way onto the nose’s mucous mem-
brane. In this way, the medicaon in the liquid is rapidly taken up by the cow, into it’s
body. The PompUnit makes sure that the liquid is pumped into the pressure-line. This
line runs to one or mulple spray locaons (e.g. a feed staon), where the SprayUnit is
located. This makes sure that, aer a feed signal is sent by the feeding system, a small
amount of liquid is atomized into a mist. The SprayUnit is mounted in such a way that
this mist is travelling onto the nose of the cow.
The PowerSpray system is compact, maintenance free, and easy to install. Moreover, the
system can be used in combinaon with every type of feeding system. Up to six
SprayUnits can be connected to a single PompUnit. In this way, one type of liquid can be
sprayed at up to six locaons. Plus of course, mulple types of liquid can be atomized at
one locaon. In order to do this, one simply has to connect mulple PompUnits to a
SprayUnit, each spraying a dierent type of liquid.
The information in this manual is for farmers and technicians.
 Dairy farmers use the information to test and adjust the PowerSpray or to list
overviews.
 Technicians use the information to install and setup the PowerSpray.

4 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
2. Safety
2.1 Introducon
The safety alert symbol idenes important safety messages on your PowerSpray and in
the manual. When you see this symbol, be alert to the possibility of personal injury or
death. Follow the instrucon of the safety message.
Safety Alert Symbol
2.2 Signal Words
Note the use of the signal words DANGER, WARNING and CAUTION with the safety
messages. The signal word for each message uses the following guidelines:
Warning! Indicates a potenally hazardous situaon that, if not avoided, could
result in death or serious injury, and includes hazards that are exposed when
guards are removed.
Danger! Indicates a imminently hazardous situaon that, if not avoided, will re-
sult in death or serious injury.
2.3 Safety Instrucons
YOU are responsible for the SAFE operaon and maintenance of your PowerSpray. YOU
must make sure that you and anyone else who is going to operate, maintain or work in
the vicinity of the PowerSpray knows all the related SAFETY informaon in this manual.
YOU are the key to safety. Good safety pracces protect you and the people around you.
Make these pracces a working part of your safety program. Make sure EVERYONE who
operates, maintains or works near the PowerSpray obeys the safety precauons. Do not
risk injury or death by ignoring good safety pracces.
 PowerSpray owners must train operators before they operate the
PowerSpray. This training must be repeated at least annually.
 The operator must read, understand and obey all safety and
operang instrucons in the manual.
 A person who has not read and understood all safety and operang
instrucons is not permied to operate the PowerSpray.
 Do not modify the equipment in any way. Unauthorized modicaon
may impair the funcon and/or safety and could aect the life of the
equipment, and persons.
 Only use approved spare parts, and make sure they are only installed
by authorized technicians.

5 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
2.3.1 General Safety
 Read and understand the manual and all safety signs before you connect
power supplies to operate or adjust the PowerSpray.
 Only trained persons are permied to operate the PowerSpray.
A rst-aid kit must be available near the PowerSpray. Store in a highly visi-
ble place.
 A carbon dioxide or foam re exnguisher must be available near the
PowerSpray. Store the re exnguisher in a highly visible place.
 Install all protecve covers and guards before you operate the PowerSpray.
 Wear the correct protecve clothing and equipment. Disconnect and iso-
late the electrical power supply before you clean or do maintenance on the
PowerSpray.
 Know the emergency medical centre number for your area.
 Contact your nearest milking equipment dealer provider if you have any
quesons
 Review safety related items with all operators frequently (annually).
2.3.2 Electrical Safety
 Only an authorized electrician must install the electrical power supply for
the PowerSpray.
 Make sure the electrical grounding of the electrical system and all parts of
the PowerSpray meet the local rules and regulaons.
 Replace any damaged electrical lines, conduits, switches and components
immediately.
 Isolate the electrical power supply before you open the PowerSpray to
work on the electrical system.
2.3.3 Installaon Safety
 Read and make sure you understand the instrucons in this manual.
 Make sure the PowerSpray is correctly installed.
2.3.4 Operang Safety
 Read and understand the applicable manual and all safety signs before you
connect power supplies to operate or adjust the PowerSpray.
 Only trained persons are permied to operate the PowerSpray.
 Switch o the electrical power supply by taking plug out of the power point
and secure the plug before you clean or do maintenance on the Pow-
erSpray.
 Close the motor cover and install addional guards before you operate the
PowerSpray.
 Keep hands, feet, hair and clothing away from all the electrical parts.
 Keep unauthorized persons, especially small children away from the
PowerSpray at all mes.
 Before the electrical supply is aached to the PowerSpray, make sure all
parts are ght and that all the parts are in good condion.
 Contact your nearest milking equipment dealer if you have any quesons.

6 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
2.3.5 Maintenance Safety
 Read and understand the applicable manual and all safety signs before you
connect power supplies to operate or adjust the PowerSpray.
 Only trained persons are permied to maintain the PowerSpray.
 Switch o the electrical power supply by taking plug out of the power
point and secure the plug before you clean or do maintenance on the Pow-
erSpray.
 Wear protecve clothing and safety goggles when you do work on the
electrical system.
 Make sure all the covers and guards are installed when maintenance work
is complete.
2.3.6 Safety Decals
 General safety messages appear in this safety messages secon. Specic
safety messages are in applicable parts of this manual when potenal
hazards may occur if the instrucons or procedures are not followed.

7 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
3. Installation instructions
3.1 General description:
The PowerSpray (g. 2) is a liquid spraying system for soluble (medical) addives. It is built
to supply these liquids to animals inside feeding staons and/or milking robots. This is
done by atomizing a soluon over the cow’s nose, and in this way over onto the mucous
membrane, which allows for rapid uptake of the soluon into the body of the cow.
Before connecng the PowerSpray to a feeding system, always consult the manual of the
corresponding feeding system. The PowerSpray can be connected to a feeding system by
using the next available feed type slot.
Please use the annexes further on in this manual for reference to order numbers and
names of individual parts
3.2 Transport en storage:
The PowerSpray will be stored in a sealed box. This box is sealed with tape and the in-
side of the box is covered with protection foil to prevent the PowerSpray from damage.
The storage of the PowerSpray will also handled in this way. Multiple PowerSpray units
can be transported on a single pallet.
Warning! Always move the box very carefully!
Warning! When unpacking the box there are different parts that may
fall out of the box! Always keep the box stable with the opening on
top!
Warning! Watch out for damages or lose ends that could cause injuries.
3.3 Safety stickers:
The user and installer are responsible for the safe operation and
maintenance of the PowerSpray. Safety stickers are used to ensure safe-
ty in and around the PowerSpray. These stickers must be placed cor-
rectly. In case of the PowerSpray, both the PompUnit and SprayUnit
have a sticker, placed on the front of the PompUnit, and the metal plate
of the SprayUnit. The stickers show product information, as well as CE-
marking (fig. 4 & 5). Please make sure these stickers are easily readable.
Applying the stickers:
 Make sure the surface is dry and clean.
 Ensure that the surface temperature won’t get below 5°C.
 Find the right position for the sticker.
 Remove a small part of the film on the backside of the sticker.
 Place the sticker on the surface, next press a small part of the ad-
hesive layer on the surface.
 Remove the foil carefully and apply the whole sticker on the sur-
face.
 Use a needle to make small air holes in the sticker and use the foil
to smooth out the sticker.
Scker maintenance:
Keep the safety sckers clean and clearly visible. Clean the sckers with
soap and water. Do not use dissolving or corrosive soluons that can
damage the sckers. Replace missing or unreadable sckers. Safety sck-
ers are available at Hanskamp. Please refer to the arcle numbers when
corresponding.
The box contains:
1. 003-90x-000 PowerSpray SprayUnit
2. 003-920-000 PowerSpray PompUnit
3. 082-341-000 Transport line 4x2,5
Oponal parts:
1. 003-919-000 Montageplaat PowerUnit
Delivery specicaons
4
Product name
CE-
marking
3
5
Product name
CE-marking
Contact-
details
Status LED
Arcle number
Arcle number
Serial number
Serial number

8 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
3.4 Installaon:
Before installing anything, check if all parts are available using the parts list at the back
of this manual. For this, please refer to Annex 1 and 2.
1. Determine where and at what height the PowerSpray PompUnit should be in-
stalled. Users that want to spray a soluon at mulple locaons, are advised to
place the PompUnit at a central locaon in the barn. The maximal length of the
pressure line is 100 meter. For the inlet line, the maximum length is 2 meter. We
advise to keep this inlet line as short as possible. It is advised to mount the Pom-
pUnit close to a wall socket, and to place the liquid container at a steady loca-
on. underneath the PompUnit. Dimensions of the PompUnit are shown in An-
nex 6. Mounng examples are can be found at www.hanskamp.nl/en.
Important! The maximal length of the pressure line is 100 meters.
The maximal length of the inlet line is 2 meters.
2. Determine where the SprayUnit should be mounted. The SprayUnit should be
placed in such a way that the sprayed mist will travel in the direcon of the
nose of the cow that is eang out of the feed trough (g. 6). To ensure this,
the SprayUnit should be mounted into the feed trough. For this, drill a 13mm
hole in the trough, together with two 4mm holes to mount the metal plate.
The plate can be used to mark holes, in case the backside of the trough allows
for limited access. Place the spray nozzle in into the hole, and connect it to the
SprayUnit on the other side of the trough (g. 7). Use the supplied mounng
equipment to secure the SprayUnit ghtly to the trough.
3. Make sure the power to the control unit is shut down. For this, please refer to
the corresponding manual.
4. Connect the other end of the cable to the next available feed type slot of the
feed system. In case of using a SprayUnit without control PCB, the duraon of
the feed signal that is sent by the feed system, should be 0.5 seconds (+/- 0.1).
This duraon corresponds with the spraying duraon. Please refer to the cor-
responding manual for the necessary informaon needed to execute this step.
Important!
Make sure the wiring is properly secured, and out of reach of animals. Other-
wise, this can result to dangerous situaons.
Danger! The PowerSpray is now under electrical voltage!
5. Connect one end of the line to the SprayUnit. It will need to be disconnected
later. The installaon does not need to be re-enclosed, yet. Lead the line back
to the PompUnit. Make sure the line is properly secured, without ght bends,
and without contact with sharp edges, as this prevents blockings and/or leak-
age of the line. As soon as the line is mounted correctly, the line can be cut to the
right length, before pushing it into the le push-in coupling of the PompUnit.
6. Drill an hole (Ø 4mm) in the lid of the liquid container. Plug in the one end of the
remaining line into the container, so that it touches the boom. Cut the line to
the right length, before pushing it into the ingoing push-in coupling of the
PompUnit.
7
6

9 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
7. Disconnect the pressure line from the SprayUnit.
8. Connect the power supply of the PowerUnit to the wall socket. The pump will
start to run (power LED on PowerUnit will ash), and liquid will travel through
the line. Reconnect the pressure line to the SprayUnit, as soon as the rst
amount of uid ows out of the end of the line. The PompUnit pump will keep
running, unl the desired pressure is reached. In case the LED ashes for longer
than 30 seconds, then probably there’s a leak in the system. The same goes for
the situaon where the LED ashes regularly, while no liquid is dispensed by
the SprayUnit.
Warning! The PowerSpray is now under electrical voltage.
Attention! Please make sure the fluid level in the connected container is filled
up on time. This prevents air entering the line, thus ensuring the pressure line
to be kept at the right pressure.
9. Check the system for any leaks or blockings. If these are not present, the
PumpUnit will only be shortly acve, just aer the SprayUnit has been acvated
by the feeding system.
3.5 Calibraon
Calibrang the PowerSpray system is done using the following steps, according to the
connected feeding system:
1. First, it is needed to bleed the air out of the SprayUnit. keep a test-tag of the
corresponding feed type in front of the tag reader. The feeding system will ac-
tuate the SprayUnit a number of mes. No collecon of the liquid is needed
yet.
2. Go to the calibraon menu of your corresponding feeding system. If necessary,
read the corresponding manual or consult your dealer.
3. Before collecng the uid, rst weigh the empty collecng bucket.
4. Place a small bucket around the nozzle, make sure the whole mist can be col-
lected.
5. Follow the calibraon steps as described in the manual of the corresponding
feeding system.
6. The volume of a single dose could be a too small value for the feeding system.
In this case, simply mulply the value by for example 10 or 100. Of course this
should be done as well when seng the desired dose per cow. If the feeding
system is displaying any storage or liquid usage, this will consequently not cor-
respond with the actual values. Please keep this in mind.
Repeat these calibraon steps every month, as well as aer relling the storage, and
aer changing the feed type.
Important! The PowerSpray is exclusively designed for liquids with a water-like
viscosity. manufacturer cannot guarantee proper funconing when using other
types of liquid.
Warning! The SprayUnit will spray as soon as it is being actuated by the feeding
system. Beforehand, one will not noce when uid will spray out of the nozzle
of the SprayUnit.
7

10 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
Maintenance
1. When maintenance has to be done on the product and it is connected to a con-
trol unit, please prevent it from starng unexpectedly. Ensure the installaon is
completely voltage-free. To do this, disconnect the power supply from the con-
trol unit.
2. It is recommended to have repairs and maintenance done by a specialist.
3. Never open the casing while the PowerSpray is sll operaonal. This with re-
gard to the danger of electric shocks or becoming trapped in the feeder auger.
4. The user/owner of the PowerSpray is expected to follow the advice and guide-
lines of the manual, in order to keep everybody safe. If these requirements are
not fullled, the manufacturer cannot be held accountable in any way for per-
sonal injury or damage to or caused by the product, and this will be solely the
responsibility of the user/owner.
Warning! When changes are being installed/mounted in the PowerSpray, make
sure to shut down the power of the PowerSpray, to prevent accidents.
3.7 Use of liquids/soluons
The to be sprayed liquid will be atomized/sprayed in the area around the cow’s nose.
Most certainly, this wil lead to part of the mist to be travelling in other direcons. It is
therefore advised to use only non-corrosive and pH-neutral uids, to prevent injuries
to animals and/or users. Before using a certain liquid, please consult the instrucon of
the corresponding product. If necessary, consult your veterinarian.
Warning! Only use the PowerSpray in combinaon with non-corrosive and pH-
neutral uids.
For your own safety, consult the safety informaon of the to be used uid, about how
to safely use this uid. When using the PowerSpray in combinaon with this uid, al-
ways take into account the described precauons. Hanskamp is not liable for any false
use of uids in combinaon with the PowerSpray.
Warning! Before using any uids/soluons in combinaon with the Pow-
erSpray, always read the safety informaon of the used uid.

11 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
Disassembly:
When disassembling the PowerSpray, all parts should be separated according to mate-
rial type, for processing through a suitable waste management system.
Please note! In case of disassembly, always switch o the electrical voltage of
the installaon
List of included amendments in this installaon and operang instrucon:
Warranty limitaons
The warranty excludes costs and expenses due to:
 incorrect use of the equipment, not in accordance with the specicaons in the
instrucons for installaon and use;
 the consequences of any intervenons by engineers other than engineers rec-
ognised and approved by Hanskamp for carrying out service, maintenance and
other technical work;
 incidents such as freezing, ice, re, ooding, inundaon or any other form of
extreme water damage, and lightening;
 defects in the electrical system or earthing system;
 damage to the electrical system caused by vermin, etcetera.
The warranty is not applicable to consequenal damage that is not related to the feed
staon itself. All systems have been tested. However, in the event of faults, Hanskamp
cannot be held responsible for consequenal damage.
Nr. Release date Chapter(s) Comments
1.1 11/2016 First release
Copyright and disclaimer
The informaon in this publicaon is intended for informaon purposes only and is not intended as sales quote.
Products may dier to those illustrated. References to brand and/or products in this installaon instrucons are solely for idencaon purpose . The com-
pany names and product names men-oned in the catalogue are trademarks of their respecve owners. No part of this publicaon may be reproduced or
transmied without the prior wrien consent of Hanskamp AgroTech BV. Although this publicaon has been compiled with the utmost care, Hanskamp
AgroTech is not liable for any damage that may result from errors or omissions in this publicaon. The Dutch installaon and operang instrucon is the
original installaon and operang instrucon. Translaons in other languages, than Dutch, use the Dutch installaon and operang instrucon as source
document. Hanskamp AgroTech accepts no liability for dierences between translaons. If there are any doubts about the content and the accuracy of the
translated installaon and operang instrucons, the Dutch installaon and operang instrucons is the authoritave document.

12 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
Declaraon for completed machinery llA
(According to annex VIIA of the Machinery Direcve 2006/42/EC, for completed machin-
ery)
We,
Hanskamp AgroTech BV
Broekstraat 17
7009 ZB Doenchem
The Netherlands
Authorised compiler(s) of the technical le:
H.J. Hanskamp
Declare enrely under our own responsibility that the product:
Art. nr.: 039-011-000 t/m 039-066-000: PowerSpray
Liquid spraying system.
to which the declaraon relates, conforms to the provisions of the following direcve(s):
- Machine Direcve 2006/42/EG
and completely or parally meets the following essenal requirements and that the rele-
vant technical documents were drawn up in accordance with Annex VIIA. The product also
complies with the spulaons in the following annex(es):
NEN-EN-ISO 12100
NEN-5509
We call your aenon to the fact where the PowerSpray has not been installed or has
not been installed in accordance with safety measures in these installaon and oper-
ang instrucons this declaraon of spulaons is null and void and so no rights can be
derived from this declaraon.
Nederland, Doenchem 14-11-2016 H.J. Hanskamp

13 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
4. FAQ
Frequent issue: Possible cause: Soluon:
Pump is running for longer
than 30 seconds.
Leakage in uid line.
End of line is not pushed in far
enough in the push-in coupling.
Line is not cued straight, before
being pushed in the push-in
coupling
Air in the line.
Find the leak spot, and replace the line if necessary.
Push in the line in the push-in coupling, with more
force.
Cut the end of the line in a straight way, and again
push it in the push-in coupling.
Make sure the uid level of the container is above the
end of the inlet line.
Bleed out the air of the line. For instrucons, read
step 8 of chapter 3.4.
SprayUnit is not spraying/not
creang a mist, when Spray-
Unit is actuated
No uid in the inlet line/ air in inlet
line.
SprayUnit is not connected the right
way.
The lter of the spray nozzle is clog-
ged.
Make sure the uid level of the container is above the
end of the inlet line.
Bleed out the air of the line if necessary. For instruc-
ons, read step 8 of chapter 3.4.
Connect the SprayUnit to the feeding sytem, using
the corresponding manual. Consult your dealer for
more informaon.
Unscrew the spray nozzle and clean the inside of the
nozzle. It is advised to use compressed air, to blow
out any blockings in the nozzle.

14 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
Annex 1: individual parts For maintenance purposes or any other reason, it is possible to re-order individual parts from your supplier. When doing so, please refer to the arcle numbers as indicated in the drawing below.

15 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
Annex 2: Individual parts of PowerSpray PompUnit (table goes for an installaon with 1
PompUnit)
Arcle number Descripon Amount
003-920-000 PowerSpray PompUnit 1-6
001-162-000 Hose clip mini 6mm ev 2
001-154-001 Pressure sensor PowerSpray PompUnit G1/4 EPDM incl. seal, 10 mm thread 1
001-200-000 Push-in coupling 1/8”x 6mm threaded outside 1
001-290-000 Cable lug 6.3x0.8 isolated 1,5mm 2
001-347-000 Metal screw M3x6 a2 cross-recessed 7
001-354-000 LED light 24V Orange 1
001-388-000 Tube 6x3.9 PU 0.01
001-465-000 Threaded adapter 1/8” x 6mm 1
001-692-000 Push-in coupling 4mm bi 1/8 threaded inside 2
001-719-000 T-piece Ø6 x 1/4" plasc 1
001-830-000 Coupling M12x1,5 1
003-915-000 PowerSpray pump housing 1
003-916-000 Scker for PowerSpray pump housing 1
003-917-000 PowerSpray pump 24VDC 180 ml/min 1
003-918-000 PowerSpray PompUnit boom mounng plate Sendzimir 1,5mm 1
011-004-000 Wago verbindingsklem 3-connecons 2
011-041-000 Wall plug power supply 230VAC-24VDC 1670mA 1
Addional parts
082-341-000 Transportline tube PA12W/25mtr 4x2,5 naturel 1

16 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
Annex 3: Individual parts SprayUnit For maintenance purposes or any other reason, it is possible to re-order individual parts from your supplier. When doing so, please refer to the arcle num- bers as indicated in the drawing below.
003-900-000: PowerSpray SprayUnit, without control PCB 003-901-000: PowerSpray SprayUnit, IM

17 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
Annex 3: Individual parts SprayUnit For maintenance purposes or any other reason, it is possible to re-order individual parts from your supplier. When doing so, please refer to the arcle num- bers as indicated in the drawing below.
003-902-000: PowerSpray SprayUnit, RIM time-controlled 003-903-000: PowerSpray SprayUnit, RIM puls-controlled

18 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
* When connecng more than 1 SprayUnit to a single PompUnit, one T-coupling is
needed for each SprayUnit.
Annex 4: Descripon of parts PowerSpray SprayUnit
Arcle number Descripon Amount
003-900-000 PowerSpray SprayUnit, without PCB 1-6
001-042-000 Nut M6 a2 2
001-064-000 Bolt M6x16 a2 2
001-100-000 Connecon cable LiYY 2x0,5mm, 4,5m 1
001-217-000 T-coupling plasc, RL22 Ø4 push-in ** 1
001-425-000 Grommet Ø14-Ø5 - 8,4 mm 1
001-564-000 Cable black, 2x0,5mm2 L=20cm 1
001-590-000 Housing control PCB black 1
001-724-000 Coupling 1/4 bu x 4mm, threaded outside 1
001-875-000 Wago connector, 2 connecons 2
002-037-000 Torx bolt M4x5 T20 4
003-558-000 Directly actuated valve 2mm (mini) 1/4” 1
003-913-000 PowerSpray mounng plate for PCB housing M4 1,5mm RVS 1
003-926-000 PowerSpray extremely ne spray nozzle 1/4” 1
003-927-000 Seal plug PVC 1
003-928-000 Vent valve Ø4 1
010-134-000 Scker serial no. for PowerSpray SprayUnit 1
Arcle number Descripon Amount
003-901-000 PowerSpray SprayUnit, IM 1-6
001-042-000 Nut M6 a2 2
001-064-000 Bolt M6x16 a2 2
001-217-000 T-coupling plasc, RL22 Ø4 push-in ** 1
001-425-000 Grommet Ø14-Ø5 - 8,4 mm 1
001-564-000 Cable black, 2x0,5mm2 L=20cm 1
001-590-000 Housing control PCB black 1
001-724-000 Coupling 1/4 bu x 4mm, threaded outside 1
001-969-000 Control PCB Intelligent Motor 1
002-006-000 Cable 4x0,5mm LiYY 4,5m (IM Motor FS connecon) 1
002-037-000 Torx bolt M4x5 T20 4
003-558-000 Directly actuated valve 2mm (mini) 1/4” 1
003-913-000 PowerSpray mounng plate for PCB housing M4 1,5mm RVS 1
003-914-000 Resistor CFR serie, 1kOhm, 1W 1
003-926-000 PowerSpray extremely ne spray nozzle 1/4” 1
003-927-000 Seal plug PVC 1
003-928-000 Vent valve Ø4 1
010-091-000 Scker for connector IM motor 1
010-134-000 Scker serial no. for PowerSpray SprayUnit 1

19 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
Annex 4: Descripon of parts PowerSpray SprayUnit
Arcle number Descripon Amount
003-902-000 PowerSpray SprayUnit, RIM me-controlled 1-6
001-042-000 Nut M6 a2 2
001-064-000 Bolt M6x16 a2 2
001-217-000 T-coupling plasc, RL22 Ø4 push-in ** 1
001-425-000 Grommet Ø14-Ø5 - 8,4 mm 1
001-564-000 Cable black, 2x0,5mm2 L=20cm 1
001-724-000 Coupling 1/4 x 4mm, threaded outside 1
001-876-000 Wago connector 5 connecons 2
002-014-000 Cable 6x0,34mm l=4,5m RIM me-controlled 1
002-037-000 Torx bolt M4x5 T20 4
003-558-000 Directly actuated valve 2mm (mini) 1/4” 1
003-913-000 PowerSpray mounng plate for PCB housing M4 1,5mm RVS 1
003-926-000 PowerSpray extremely ne spray nozzle 1/4” 1
003-927-000 Seal plug PVC 1
003-928-000 Vent valve Ø4 1
010-134-000 Scker serial no. for PowerSpray SprayUnit 1
010-220-000 Scker for connector RIM 011-095-000 1
011-043-000 Control PCB RIM-motor 1
011-045-000 Housing control PCB black 1
Arcle number Descripon Amount
003-903-000 PowerSpray SprayUnit, RIM pulse-controlled 1-6
001-042-000 Nut M6 a2 2
001-064-000 Bolt M6x16 a2 2
001-217-000 T-coupling plasc, RL22 Ø4 push-in ** 1
001-425-000 Grommet Ø14-Ø5 - 8,4 mm 1
001-564-000 Cable black, 2x0,5mm2 L=20cm 1
001-724-000 Coupling 1/4 x 4mm, threaded outside 1
002-016-000 Cable 6x0,34mm l=4,5m RIM pulse-controlled 1
002-030-000 Connector for Lely A4 PCB, RIM puls 1
002-037-000 Torx bolt M4x5 T20 4
003-558-000 Directly actuated valve 2mm (mini) 1/4” 1
003-913-000 PowerSpray mounng plate for PCB housing M4 1,5mm RVS 1
003-926-000 PowerSpray extremely ne spray nozzle 1/4” 1
003-927-000 Seal plug PVC 1
003-928-000 Vent valve Ø4 1
010-134-000 Scker serial no. for PowerSpray SprayUnit 1
010-220-000 Scker for connector RIM 011-125-000 1
011-043-000 Control PCB RIM-motor 1
011-122-000 Housing control PCB transparent 1
** When connecng more than 1 SprayUnit to a single PompUnit, one T-coupling is
needed for each SprayUnit.

20 - 22
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
PowerSpray
EN Vernevelsysteem, Zerstäubungssystem, liquids spraying system, vaporisateur de liquides
Annex 5: Oponal parts
003-919-000: Mounting plate for PowerSpray PompUnit
Arcle number Descripon Amount
001-639-000 Metal screw M4x10 a2 cross-recessed 4
001-856-000 Self-locking bolt M4 a2 4
003-919-001 Mounng plate stainless steel 1,5mm 1
004-125-000 Wire bracket 1¼" galvanized with 2x M10 nut 2