Hanskamp PipeFeeder User guide

EN
Installaon and operang instrucon
Arcle number: 1847
Datum: August 2014
Version 2.2 - Translaon of Original Instrucons for use
According to Annex 1 Chapter 1.7.4 Machine guideline 2006/42/EG
Zelhem,
The Netherlands
www.hanskamp.nl
24VAC & 12-24VDC
PipeFeeder

2 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
Preface
Manual Contents
This manual contains the informaon necessary for the correct installaon and operaon
of a Hanskamp PipeFeeder.
Study and understand this informaon thoroughly before conguraon of the PipeFeeder.
Failure to do so could result in damage to equipment. Please consult your milking equip-
ment dealer if you do not understand the informaon in this manual, or if you need addi-
onal informaon. All informaon in this manual has been compiled with care. Hanskamp
shall not be liable for errors or faults in this manual. The recommendaons are meant to
serve as guidelines. All instrucons, pictures and specicaons in this manual are based
on the latest informaon that was available at the me of publicaon. Your PipeFeeder
may comprise improvements, features or opons that are not covered in this manual.
Applicability
The table below shows the type numbers of the PipeFeeder for which this manual is appli-
cable.
Model designaon
Contact number Local Service Provider
We suggest you write the name, address, telephone number and e-mail address of your
local service provider contact in the table below. This makes sure you can easily nd the
informaon.
Model Model number
PipeFeeder 80 gram rotaon 27000 t/m 27999
PipeFeeder 35 gram rotaon 28000 t/m 28999
Name
Adress
Telephone number
E-mail address

3 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
1. Introducon
The PipeFeeder excels in durability, simplicity and precision. The concentrate dosing unit
was designed by technicians from the farming sector. They are experts who know that
dairy farmers want to save on feed costs by dispensing precisely the right amount. The
FeedStaon is supplied with an innovave PipeFeeder concentrate feeding system from
Hanskamp, which ensures pellets are fed precisely and silently.
The PipeFeeder features an ingenious an-spill system, also developed by Hanskamp. On-
ce the desired amount of feed has been released no further concentrate falls into the
trough thus discouraging cows from banging against the FeedStaon, robot or in the mil-
king parlor.
The informaon in this manual is for farmers and technicians.
 Dairy farmers use the informaon to test and adjust the PipeFeeder or to list
overviews.
 Technicians use the informaon to install and setup the PipeFeeder.

4 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
2. Safety
2.1 Introducon
The safety alert symbol idenes important safety messages on your PipeFeeder and in
the manual. When you see this symbol, be alert to the possibility of personal injury or
death. Follow the instrucon of the safety message.
Safety Alert Symbol
2.2 Signal Words
Note the use of the signal words DANGER, WARNING and CAUTION with the safety mes-
sages. The signal word for each message uses the following guidelines:
Warning! Indicates a potenally hazardous situaon that, if not avoided, could re-
sult in death or serious injury, and includes hazards that are exposed when guards
are removed.
Danger! Indicates a imminently hazardous situaon that, if not avoided, will re-sult
in death or serious injury.
2.3 Safety Instrucons
YOU are responsible for the SAFE operaon and maintenance of your PipeFeeder. YOU
must make sure that you and anyone else who is going to operate, maintain or work in
the vicinity of the PipeFeeder knows all the related SAFETY informaon in this manual.
YOU are the key to safety. Good safety pracces protect you and the people around you.
Make these pracces a working part of your safety program. Make sure EVERYONE who
operates, maintains or works near the PipeFeeder obeys the safety precauons. Do not
risk injury or death by ignoring good safety pracces.
 PipeFeeder owners must train operators before they operate the PipeFeeder. This
training must be repeated at least annually.
 The operator must read, understand and obey all safety and operang instrucons
in the manual.
 A person who has not read and understood all safety and operanginstrucons is
not permied to operate the PipeFeeder.
 Do not modify the equipment in any way. Unauthorized modicaon may impair
the funcon and/or safety and could aect the life of the equipment, and persons.
 Only use approved spare parts, and make sure they are only installed by authori-
zed technicians.

5 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
2.3.1 General Safety
 Read and understand the manual and all safety signs before you connect power
supplies to operate, maintain or adjust the PipeFeeder.
 Only trained persons are permied to operate the PipeFeeder. A rst-aid kit must
be available near the PipeFeeder. Store in a highly visible place.
 A carbon dioxide or foam re exnguisher must be available near the PipeFeeder.
Store the re exnguisher in a highly visible place.
 Install all protecve covers and guards before you operate the PipeFeeder.
 Wear the correct protecve clothing and equipment. Disconnect and isolate the
electrical power supply before you clean or do maintenance on the PipeFeeder,
also be sure that the compressed air supply is depressurised.
 Know the emergency medical centre number for your area.
 Contact your nearest milking equipment dealer provider if you have any ques-
ons
 Review safety related items with all operators frequently (annually).
2.3.2 Electrical Safety
 Only an authorized electrician must install the electrical power supply for the
PipeFeeder.
 Make sure the electrical grounding of the electrical system and all parts of the
PipeFeeder meet the local rules and regulaons.
 Replace any damaged electrical lines, conduits, switches and components imme-
diately.
 Isolate the electrical power supply before you open the lid of the PipeFeeder to
work on the electrical system.
2.3.3 Installaon Safety
 Read and understand the instrucons in this manual.
 Make sure the PipeFeeder is correctly installed.
2.3.4 Operang Safety
 Read and understand the applicable manual and all safety signs before you con-
nect power supplies to operate, maintain or adjust the PipeFeeder.
 Only trained persons are permied to operate the PipeFeeder.
 Switch o the electrical power supply by taking plug out of the power point and
secure the plug before you clean or do maintenance on the PipeFeeder. Be sure
that the compressed air supply is depressurised, switch the compressor of by
using the main switch of the compressor, and close the air valve.
 Install the covers and guards before you operate the PipeFeeder.
 Keep hands, feet, hair and clothing away from all the electrical parts.
 Keep unauthorized persons, especially small children away from the PipeFeeder
at all mes.
 Before the electrical supply is aached to the PipeFeeder, make sure all parts are
ght and that all the parts are in good condion.
 Contact your nearest milking equipment dealer if you have any quesons.

6 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
2.3.5 Maintenance Safety
 Read and understand the applicable manual and all safety signs before you
connect power supplies to operate, maintain or adjust the PipeFeeder.
 Only trained persons are permied to maintain the PipeFeeder.
 Switch o the electrical power supply by taking plug out of the power point and
secure the plug before you clean or do maintenance on the PipeFeeder.
 Wear protecve clothing and safety goggles when you do work on the pneumac
system.
 Make sure all the covers and guards are installed when maintenance work is com-
plete.
2.3.6 Safety Decals
 General safety messages appear in this safety messages secon. Specic safety
messages are in applicable parts of this manual when potenal hazards may occur
if the instrucons or procedures are not followed.

7 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
3. Installation instruction
General descripon:
Hanskamp’s PipeFeeder is an electric feed dosing system developed for feeding concen-
trates in pellet form (Pic. 1) PipeFeeder is designed for the supply of concentrate, either
linked to the feed computer and used for milking stall feeding. Please read the whole in-
stallaon instrucons and keep the safety instrucons in mind.
If the PipeFeeder is controlled by an ControlUnit from Hanskamp, see also installaon
instrucons Art. No. 1841. This can be requested from the manufacturer. If the PipeFeed-
er is not controlled by the ControlUnit, always consult the manual for the relevant control
unit. If the PipeFeeder incorporates a DosPrint from Hanskamp, please consult the instal-
laon instrucon no. 1840 for connecng and adjusng the PCB.
See the annex for the order numbers and names of the various parts.
Transport and storage:
The PipeFeeder will be shipped in a box containing two PipeFeeders. Where a complete
milking stall feeding installaon is being shipped the boxes will be transported on a pal-
let. This pallet is completely sealed and the corners are covered with tape to prevent
damage. The PipeFeeder is also stored this way.
Please note! Always use an appropriate vehicle (forkli truck, pallet fork,
pump truck, etc.) to move the pallet.
Please note! Parts may fall o the pallet/box when it is being unpacked.
The box contains:
1. 2x PipeFeeder feeding dosator;
2. 1x bag with 4 pipe clamps
Art.No.:1902;
3. 2x cover for motor;
4. 2x bag with screws for cover and
grommet
Type descripon;
To be found on the backside of the pipe,
just under the plasc part
Product
descripon
Arcle number
CE
marking
Address
1
Serial
Number

8 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
Safety sckers:
The user and installer are responsible for the safe operaon and maintenance of the Pipe-
Feeder. Safety sckers are used to ensure safety in and around the PipeFeeder. These
sckers must be placed correctly. Informaon about which sckers should be aached
where can be found further on in these instrucons for installaon and use (for example
Fig. 10).
Applying the sckers:
 Make sure the surface is dry and clean.
 Make sure the surface temperature is at least 5°C.
 Find the right posion for the scker.
 Remove a small poron of the foil on the back.
 Place the scker on the surface and press a small poron of the self-adhesive
layer onto the surface.
 Carefully remove the foil and press down the rest of the scker.
 Remove any air bubbles with a needle and use the foil to smoothen the scker.
Maintenance of the sckers:
 Keep the safety sckers clean and legible. Clean the safety sckers with soap and
water. Do not use any solvents or abrasives that could damage the safety sckers.
 Replace missing or illegible safety sckers.
Safety sckers are available by Hanskamp. Always use the Arcle numbers in correspond-
ence.
1702 Warning scker:
Danger risk of geng your hand
stuck under the pipe.
1755 Warning scker:
The PipeFeeder can start automa-
cally.

9 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
Installaon:
1. The PipeFeeder is designed to be mounted on a wall. First of all ascertain where the
PipeFeeder needs to hang and at what height. To do this, use the mounng holes in
the assembly brackets provided for this purpose (item no. 1902).
2. Grease, before assembly, the bolts and nuts with sucient copper grease.
3. If the distance between the feeder and the dosing unit is too great we advise you to
use a fall pipe ed directly underneath the dosing unit. The PipeFeeder is designed
to hang directly in the feeding trough so that the fall height remains low so noise and
dust are reduced. Sample installaons can be found at www.hanskamp.nl.
Please note! No mounng material is supplied to mount the PipeFeeder to the
wall or on the feeding staon.
Please note! Always allow ±10 ll 15cm of space under the PipeFeeder.
This way air can run underneath the PipeFeeder.
4. Use a well-shielded electricity cable to connect the dosing unit.
See the annex on page 15 for the connecon diagram for the various motors
(AC & DC). The motor turns counterclockwise as standard.
Please note! When assembling always rst switch o the
electricity to the control unit.
Please note! Make sure that there is always a plug or lockable switch
placed between the Pipe Feeder and the energy supply
so that power can be disconnected.
5. Using the supplied membrane grommet (item no. 1947), t the cable through the lid
of the PipeFeeder. To do this, drill a hole (Ø 16 mm) at the desired posion in the lid.
Then connect the other end of the cable to the desired output of the control unit.
6. Make a solid and closed connecon with the supply auger. The top connecon of the
PipeFeeder is Ø125mm. This ts a slide coupling socket of PVC or PP exactly across.
Make sure to not allow water, moist or dirt in the stock of the PipeFeeder.
Please note! An insucient seal with the supply auger can cause problems when oper-
ang the PipeFeeder.
2
afdekkap
16

10 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
Adjusng the DC PipeFeeder an-spill device
7. The DC version of the PipeFeeder (an-spill) should be correctly
adjusted before this is put into service. Adjustment is performed
as follows:
 Ensure that the PipeFeeder is full of feed than allow the
motor to rotate once (give signal).
 For the sengs of AC with DosPrint Pipefeeders, check the DosPrint man-
ual. (Art.nr. 1825)
Please note! Make sure to rst switch o the electric
power to the control unit before the next step.
 Remove the lid from the PipeFeeder. Remove the motor plate by unscrew-
ing 4 bolts.
 Remove the motor with motor plate and connector from the sha.
 Turn the star on top of the drive sha. Make sure that the arrow on the star is
level with the recess on top of the stainless steel pipe.
 Push the motor with motor plate and connector back onto the drive axis.
Mount these by screwing the 4 bolts ght again.(pic.3)
 Fit the lid back onto the PipeFeeder.
 Switch the electronic power back on.
 Fill the PipeFeeder and allow to rotate once for control (give signal).
This adjustment should be applied in both the milking stall feeding installaon, in parlour,
and in the feeding box, out of parlour.
8. When installaon is not completely correct the plasc part will be able to rotate
freely with respect to the stainless steel tube. When the plasc part is rotated in
case of the DC version the adjusng procedure should be followed again (step 7).
In addion it must be ensured that aer mounng or twisng of the plasc part,
the motor is correctly placed onto the axis
Important!
 Only when the motor is correctly adjusted can Hanskamp Agro
Tech guarantee that the PipeFeeder is An-spill.
 Make sure that all the wires are neatly concealed out of reach of
animals. Otherwise hazardous situaons can emerge.
 Before you run the PipeFeeder, always t the lid which covers the
motor carefully. Otherwise hazardous situaons can emerge
(pic. 4).
9. The PipeFeeder has fully electrical operaon. The motor drives the axis that turns a
scoop mechanism at the boom of the stainless steel pipe (Ø129 x 2mm). This mech-
anism delivers the feed. If a switch is used to control several dosing units at the same
me, such asl on each side of the parlour (milking stall feeding), then several Pipe-
Feeder dosing units can be connected to a single feeding line. Please note the maxi-
mum permissible current, which is stated on the power supply (art.nr. 2812 or 2813
PowerUnit), won’t be exceeded.
3
4

11 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
Calibraon
10. The PipeFeeder is calibrated by allowing the feeding computer to emit a pulse ten
mes. You then weigh the issued feed, divide this by 10 and enter this value into
the feeding computer. Repeat this procedure every month and also aer changing
the feed type.
Important!
 The PipeFeeder is only intended for cylindrical concentrate with a
diameter of Ø4 to Ø6 mm. The manufacturer cannot guarantee
proper funconing for other shapes or dimensions.
 During the installaon of the PipeFeeder ensure the pressure of
the concentrate on the dosing unit is greater than 50kg.
 Never insert your hand into the boom of the PipeFeeder when it
is sll in operaon or is connected to the electrical
power supply (pic. 5).The size of the exit point is limited by a
bar to prevent cuts.
Maintenance
1. Check the PipeFeeder installaon daily for faults and wear. Do this by means of a
control test on the feed motors. Make sure that the vibraons and noise caused by
the PipeFeeder are reduced as much as possible
2. If the PipeFeeder needs maintenance and is connected to the controls ensure that
the PipeFeeder cannot start unexpectedly. Make sure there is no voltage on the
installaon! To do this plug the power supply o at the control unit of the dosing
motor.
3. It is recommended to have repairs and maintenance carried out by a specialist.
4. To avoid electric shocks or geng trapped in the feed auger never open the hous
ing when the PipeFeeder is sll running.
5. For the safety of all concerned the user/owner of the PipeFeeder should follow the
advice and direcons given in the installaon instrucons. If it is not possible to
follow this it is the responsibility of the user and the manufacturer cannot be held
responsible/liable for any injury or damage to or by the product.
Please note! In case of maintenance make sure to always rst switch o the electricity
of the installaon.
Cleaning
Clean the PipeFeeder regularly with a moist cloth. Do not spray water under the hood or
in the stock pipe. To guarantee the equipment funcons correctly make sure the exit
point is clean and stays clean.
Please note! Do not spray with high pressure in or on the PipeFeeder. This can cause
blockage.
Disassembly
In case of disassembly all parts must be separated by material type for processing
through a suitable waste management system.
Please note! In case of disassembly always switch o the electrical voltage of the instal-
laon.
1976 Ban scker:
It is prohibited to spray with water.
5

12 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
Warranty limitaons
The warranty excludes costs and expenses due to:
 Incorrect use of the equipment, not in accordance with the specicaons in the
instrucons for installaon and use;
 The consequences of any intervenons by engineers other than engineers recog-
nised and approved by Hanskamp for carrying out service, maintenance and other
technical work;
 Incidents such as freezing, ice, re, ooding, inundaon or any other form of ex-
treme water damage, and lightening;
 Defects in the electrical system or earthing system;
 Damage to the electrical system caused by vermin and so forth.
The warranty is not applicable to consequenal damage that is not related to the feed
staon itself. All systems have been tested. However, in the event of faults, Hanskamp
cannot be held responsible for consequenal damage.
List of included amendments in these installaon and operang instrucons:
Copyright and disclaimer
The informaon given in this publicaon is provided for informaon purposes only and does not constute an oer for sale. The products supplied may
dier from those illustrated. No part of this publicaon may be reproduced or made public without prior permission in wring from Hanskamp AgroTech
BV. Although this publicaon was put together with the utmost care, Hanskamp AgroTech is not liable for any damage that might arise due to errors or
gaps in this publicaon.
The instrucons for installaon and use in Dutch are the original instrucons for installaon and use. The translaons into other languages have used the
Dutch instrucons for installaon and use as the source document. Hanskamp AgroTech does not accept any liability for dierences between the trans-
laons. If there are doubts about the content and accuracy of the translated instrucons for installaon and use, the Dutch instrucons for installaon
and use constute the authoritave document.
Nr. Release date Chapter(s) Comments
106/2012 All First release
1.1 01/2013 Installaon Addion DosPrint
2.0 10/2013 All Up-to-date for Versie 2.
2.1 06/2014 All Update to standard for 2014
2.2 08/2014 All New name and logo added

13 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
Declaraon for completed machinery llA
(According to annex VIIA of the Machinery Direcve 2006/42/EC, for completed machin-
ery)
We,
Hanskamp AgroTech BV
Arendsenweg 7
7021 PC Zelhem
The Netherlands
Authorised compiler(s) of the technical le:
H.J. Hanskamp
Declare enrely under our own responsibility that the product:
27000 PipeFeeder (24VAC & 12-24VDC)
Dosator for concentrate supply for dairy cale
to which the declaraon relates, fully complies with the provisions of the following di-
recve(s):
Machine Direcve 2006/42/EC
and completely or parally meets the following essenal requirements and that the rele-
vant technical documents were drawn up in accordance with annex VIIA. The product also
complies with the spulaons in the following annex(es):
NEN-EN-ISO 12100
NEN-EN-IEC 60204-1
NEN-EN-IEC 13849-1
We call your aenon to the fact where the PipeFeeder has not been installed or has
not been installed in accordance with safety measures in these installaon and oper-
ang instrucons this declaraon of spulaons is null and void and so no rights can be
derived from this declaraon.
The Netherlands, Zelhem 4-10-2013 H.J. Hanskamp

14 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
4. FAQ
Occuring problem Possible cause Soluon
There is no feed. No feed in stock pipe. Check auger and silo.
Motor is not controlled by the controller.
Take of the cover at the motor and check
the indicator lights on the PCB.
Check supply and control (voltage) (see ma-
nual ControlUnit. Provided when it is used as
a control.)
Check if the rotor spins. Connecon piece
between the motor and drive-sha could
be broken.
Remove motor of rotor and reinsert (note
sengs for an spill)(pag.10, step 7)
Conspaon by, for example wood or
plasc.
Remove the PipeFeeder o the wall and sha-
ke it empty. The rotor can be rotated by hand
when it is empty.
Check if you have a an spill version of the
PipeFeeder. (g.6)
For AC with DosPrint: check instuons/
funcon. For the correct instuons down-
load the manual, see website.
PipeFeeder isn’t an spill.
PipeFeeder isn’t set. For DC, see pag.10, step 7
PipeFeeder doesn’t distribute
the proper amount.
Calibraon is incorrect. Calibrate the controller. (see page 11, step
10)

15 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
Annexes
Hanskamp can supply the following types of dosing units:
Technical data
For more informaon: www.hanskamp.nl/en
Schemacally overview
PipeFeeder ACPipeFeeder DC
Art. Nr.: 27321
6
Product:
27 = PipeFeeder
80 Gramm/
rotaon
28 = PipeFeeder
35 Gramm/
rotaon
Color:
1 = Black
2 = Green
3 = Blue
4 = Red
Lengte:
0 = Extra short L= 821 mm
1 = Short L=1141 mm
2 = Normal (normal PF) L=1440 mm
3 = Long (FeedStaon) L=1926 mm
Motor:
1 = 1650 24VDC 28 rpm SolidState++ (An-spill) DV
2 = 1069 24VAC 6 rpm OV
3 = 1069 24VAC 6 rpm with DosPrint (An-spill) OV
4 = 1652 24VDC 28 rpm (Intelligent / An-spill) DV
5 = 1440 24VDC 41 rpm (An-spill) DV
6 = 11021 24VDC 28 rpm (An-spill) Solid State 5 DV
7 = 1663 24VDC 28 rpm OV
8 = 1001 24VDC 41 rpm (An-spill) DV
Example : Art. No.: 27321 =
 A 1500mm normal blue PipeFeeder with SolidState++ motor
 HighSpeed version, always motor 1631 24VDC 120 Rpm
 PipeFeeder in FeedStaon? Use always length 3.
Color:
1 = Black
2 = Green
3 = Blue
4 = Red
24VAC (evt. with DosPrint) (27002,27003)
Supply voltage 24VAC
Current, no load 350 mA
Current, nominal 360 mA
Current, max 440 mA
Condensor 22 μF
Electric motor 6 rpm
Capacity 25gr poron/compartment
Content ca. 20 liter
Rotaon direcon of sha counterclockwise
12-24VDC Intelligent Motor (27004, 28004)
Supply voltage 12-24VDC stabilized power
supply
Input signal 12-24V AC/DC
Current, no load 0,5 A
Current, nominal 0,7A
Current, max >2 A (auto reset 6 sec.)
Electric motor 28 rpm
Capacity 80gr rotaon (27000) 35 gr pro
rotaon (28000)
Content ca. 20 liter (12 kg.)
Rotaon direcon of sha counterclockwise

16 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
Loose components:
It is possible to reorder loose components from your supplier for maintenance, or for
any other reason. Please use the item numbers shown below on the drawing.
89
27000 PipeFeeder DC
7
Fig. 8

17 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
Descripon of the components of Figs. 7 to 9:
Arcle-
number
Descripon Number
1001 Silver motor 40rpm 24V DC, with cable and
resistor. (GEA/Wesalia)
1
1034 Tap bolt M6x12 ad DIN 933 3
1366 Spring Washer M6 a2 DIN 137B 3
1440 Silver motor 40rpm 24V DC, without cable.
(GEA/Wesalia)
1
1448 Connector AC-motor* 1
1639 Tap bolt M4x10 a2 cross recessed* 4
1650 Motor SOLID STATE++, 28rpm (without sleeve
contacts)
1
1652 Intelligent Black Motor, 28 rpm (without slee-
ve contacts)
1872 Top Plate AC* 1
1873 Top Plate DC & HighSpeed 1
1877 Capacitor on print (easy to connect) 22μF* 1
1888 Stainless steel pipe Ø129x2mm l= 990 mm 1
1889 Bearing Nylon Ø8.0 1
1890 Motor plate for DC-motor 1
1891 Motor plate for AC-motor* 1
1893 Central plate 1
1894 Boom plate AC* 1
1895 Angled safety plate 1
1896 Boom plate DC & HighSpeed 1
1899 Sheet secon of sealed compartment 1
1902 Wall mounng bracket Ø129 complete 2
1903 MDPE plasc T-piece 45° with lid, Green 1
1904 MDPE plasc T-piece 45° with lid, Black 1
1924 MDPE plasc T-piece 45° with lid, Blue 1
1925 MDPE plasc T-piece 45° with lid, Red 1
Motor depends on type of feeder. For the correct
arcle code, see the overview on page 5.
* parts only to be used in combinaon with an AC
–motor.
Arcle-
number
Descripon Number
1933 Pressure plate 90° 1
1934 Connector DC motor 1
1937 Scker CE PipeFeeder with
serial number
1
1939 Assembly boom plate com-
plete AC*
1
1942 Assembly boom plate DC &
HighSpeed
1
1947 Membrane grommet thermo-
plasc elastomer
1
1951 Blind rivet DIN all stainless
steel a2
12
1955 Chipboardscrew 4x13 stain-
less steel a2 (pozidriv)
7
1957 Tap bolt M4x8 a2 cross re-
cessed
4
1958 Hexagon head screw
M4x10mm a2*
4
1976 Ban scker ‘No spraying with
water’ Ø 33 mm
1
1982 Mixer 2mm AISI304 2

18 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
Installaon dimensions:
Visit us on:
10

19 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC

20 - 20
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
Pipefeeder
EN 24VAC & 12-24VDC
Hanskamp
Arendsenweg 7
7021 PC Zelhem
The Netherlands
Tel: +31 (0)314 - 393 797
Fax: +31 (0)314 - 393 826
www.hanskamp.nl