Happy Beds Malmo - King User manual

Assembly Instructions
Malmo - King
www.happybeds.co.uk
Important before assembly:
.
Health & Safety:
.
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product, to avoid
scratches and damaging the product or the floor.
Assemble the product as close to its intended final location/room as possible.
Do NOT use any power tools as this may damage the frame.
This product or some parts of this product will be heavy. Please use an assistant when lifting.
Please keep small parts out of reach of children.
Always use on a level, even surface.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Please keep these instructions for future reference.

@
This product or some parts of this product will be heavy. Please use an assistant
when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause
damage to the joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please
contact us by visiting:
https://www.happybeds.co.uk/customer-service
(Not metal)
These tools are not
necessary, but may
help to assemble
certain parts of the
product.
Do NOT use any power
tools as this may
damage the frame.

Page 3of 12
Parts List
Parts Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Box
Qty
1
1
1
1
1
1
1
1
Headboard Frame
Left Wooden Post
Right Wooden Post
Footboard
Left Side Rail
Right Side Rail
Centre Storage Panel
Back Storage Panel
2 / 4
2
1
1
1
1
2
28
Slat
Hydraulic Arm Spacer
Left Side Metal Bar
Right Side Metal Bar
Headboard End Metal Bar
Footboard End Metal Bar
Center Metal Bar
Support Leg
1
Left Hydraulic Base Support c/w Pump Stopper
Right Hydraulic Base Support
Hydraulic Base Pump
1
2
1
17
18
19
4 / 4
3 / 4
1 / 4
1 / 4

Page 4of 12
Mini Fix
8 x 30 mm Wooden Dowel
M6 x 90 mm RBW + Barrel Nut
M8 x 15 mm JCBC Bolt RBW
M8 x 35 mm JCBC Bolt RBW
Bracket 20mm x 58mm
Base Handle
M6 x 40 mm JCBC Bolt BLK
Single Slat Cap
M6 Allen Key
M12.8 Spanner
Metal Corner Block
M8 x 25 mm JCBC Bolt RBW
M6 x 15 mm JCBC Bolt RBW
Belt Handle
Double Slat Cap
M8 Allen Key
Hardware List (Found in box #)
Parts Description
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
BoxQty
4
12
2
4
16
8
10
8
4
2
1
12
6
28
14
1
1
1
Q
R
S
** You will also need a screwdriver and small mallet ( not provided ).
Wooden Button 4
M8 x 45 mm JCBB Bolt RBW with Nut
Bracket, Spring & Flat Washer
4
Washer Bracket
8
Flat Washer
2
Self adhesive 4mm X 35mm
T
U
V
3 / 4
4 / 4
3 / 4

Page 5of 12
Step 1: Attach the headboard frame (1) and back storage panel (8) to the left wooden post (2) and right
wooden post (3). Secure the headboard frame using hardware parts B, D and P, then secure the back
storage panel with hardware parts B, H and I.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
D
PB1
D
P
I
H
B
8
2
3
Step 2: Firstly, fix the hydraulic pump to each hydraulic base as shown in diagram 2.1. Next, fix the left
& right hydraulic spacer together with hydraulic base supporter to the both side rails using bolts G and
than screw the minifix part Ato the both side rails
as shown in diagram 2.2.
G
9
17
9
19
19
17/18 19
Hydraulic Pump right installation.
2.1
2.2
A
LEFT
5
LEFT
LEFT

Page 6of 12
Step 4: Attach the headboard frame (1) and footboard (4) using hardware part E.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 3: Join together the left side rail (5) and right side rail (6) with the centre storage panels (7) using
hardware parts Aand B.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
A
B
7
6
5
1
4
E

Page 7of 12
Step 5: Fix metal corner block Cto the edge of footboard and side rails with bolt Fas shown.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
L
T
K
L
14
11
13
10
12
J
LU
Step 6: Join together all the bed base parts (10),(11),(12),(13) and (14) using hardware parts L,T,U and
also attach hardware part Kby slot to the part (13). And than attach hardware parts Jusing hardware part L
as shown.Important note: Please assemble follow arrow direction.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
F
C

Page 8of 12
NO16
Step 7: Insert the slats (16) to hardware parts Nand Othen press into the base making sure they are secure.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 10: Assemble the bed base on the right & left hydraulic frame and fix bolts M starting from ' 1 ' to ' 3 ' as
shown and fix the support leg (15) to the bed base as shown and than stick it the self adhesive V as shown .
Important note : Do not tighten the bolts yet!, and this assemble must be done by two persons.
M
15
3
2
1
V
V
Left
Right

Page 9of 12
Step 10: Adjust the bed base making sure that the distance to the footboard is approximately 15 mm to
above. Tighten all bolts and screws now.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
FOOTBOARD
15 mm to above
HEADBOARD

IMPORTANT NOTE
WHEN THE BED IS BUILT AND THE MATTRESS FRAME IS AT 45 DEGREE
ANGLE PLEASE PLACE THE MATTRESS ON THE BED.
PLEASE NOTE THAT THE WEIGHT OF THE MATTRESS IS REQUIRED TO
HELP CLOSE THE BED.
TO LOWER THE SLEEPING PLATFORM STAND AT THE FOOT END OF THE
BED AND PUSH SHARPLY
DOWNWARDS USING BOTH HANDS.
MATTRESS
Page 10 of 12
WARNING: Take care when assembling the base. Assemble the ottoman
as closed to its final position. The Ottoman has a powerful, mechanism
and after assembly should only be opened when the mattress is in place.

CAUTION :
PLEASE USE HYDRAULIC PUMP STOPPER FOR SAFETY PURPOSE.
Page 11 of 12
HYDRAULIC PUMP
STOPPER
(LOCK IN)
(LOCK OUT)

www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the product across the
floor as this will cause damage to the joints. If the product is used on hard flooring, such as
wood or laminated floor, you must place some protection under the legs to stop the product
from moving. If this is not adhered to, it could result in failure to the product that will invalidate
the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
We’ve tried to make this product as easy to assemble as possible. In the unlikely event that
you have problems putting it together or have damaged or missing pieces, please contact
us by visiting:
https://www.happybeds.co.uk/customer-service
Notes