Allen + Roth 9012SSMV User manual

IS9112-I4
GLASS & CHROME WALL SHELF
ITEM #0045177
MODEL #9012SSMV
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-439-9800, 8 a.m. - 8p.m. EST, Monday - Friday.
Français p. 9
Español p. 17
allen + roth® is a registered trademark
of LF, LLC. All Rights Reserved.

1IS9112-I4
PACKAGE CONTENTS
Part Description Quantity
ATop Piece 1
BBottom Piece 1
CTubular Shelves 2
DGlass Shelves 2
EShort Tubes 4
FMedium Tubes 4
GLong Tubes 4
HThin Interior Tubes 4
IChrome Collars 24
J Top Caps4
KBottom Caps4
I
E
K
B
C
D
D
C
A
J
G
F
H

2IS9112-I4
HARDWARE CONTENTS
Part Quantity
Description
Picture
(Shown to size)
PREPARATION
Before cutting, drilling or hammering into any wall surface, verify the location of electrical, plumbing and gas
lines. Cutting any of these may cause serious injury. If needed, contact your electrician, plumber or service
person.
WARNING AND CAUTIONS
Before beginning assembly of the product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble or install the
product. Contact customer service for replacement parts.
Estimated Assembly Time:
20 minutes (We recommend two people for assembly)
Tools Required for Assembly (included) : Hex Wrench
Tools Required for Assembly (not included) : Phillips Screwdriver and Hammer
Threaded Inserts4
Large Screws 4
Rubber Collars 8
AA
BB
CC

3IS9112-I4
ASSEMBLY INSTRUCTIONS
Screw threaded inserts (AA) into one end of thin interior
tubes (H).
1.
Screw thin interior tubes (H) into top piece (A).
2.
Fig. 2
Fig. 1
Hardware Used
x 4
Threaded Inserts
AA
AA
H
H
A
IMPORTANT:
Make sure top
piece (A) is orient-
ed like this.

4
Slide chrome collars (I) and short tubes (E) onto thin
interior tubes (H).
3.
Slide a tubular shelf (C), chrome collars (I) and long
tubes (G) onto thin interior tubes (H).
4.
Fig. 3
Fig. 4
IS9112-I4
I
E
H
G
I
H
C
NOTE:
The cross wires should
be face up.

5IS9112-I4
5. Slide chrome collars (I) and a tubular shelf (C) onto
thin interior tubes (H).
Slide medium tubes (F) and chrome collars (I) onto
thin interior tubes (H). Fasten bottom piece (B) to unit
with large screws (BB).
6.
Fig. 5
Fig. 6
Hardware Used
x 4
Large Screws
BB
I
C
NOTE:
The cross wires should
be face up.
BB
B
I
F
IMPORTANT:
Make sure bottom
piece (B) is oriented
like this.
H
H

6
7. Turn unit over. Screw on top caps (J). Insert bottom
caps (K).
Install rubber collars (CC).
8.
Fig. 7
Fig. 8
IS9112-I4
CC
K
J
Hardware Used
x 8
Rubber Collars
CC

7IS9112-I4
9. Mark mounting points on wall through holes in the back
tubes of the unit. Hammer wall anchors (not included) into
wall, unless mounting screws (not included) will go directly
into a stud.
(NOTE: Do not use a wall anchor if mounting screw will be
going into a stud.)
Place unit against wall, lining up holes in wall and holes in
back tubes. Complete mounting by tightening mounting
screws (not included) into studs or wall anchors (not includ-
ed).
Fig. 9
D
10. Install glass shelves (D).
Fig. 10
Cleaning with a dry cloth may be sufficient, but for other stains or marks wipe gently with a damp cloth.
DO NOT use strong detergents or abrasive cleaners; they may damage the surface of this product.
CARE AND MAINTENANCE

8IS9112-I4
If you have any questions regarding the product, please call customer service at 1-866-439-9800, 8 a.m. - 8p.m
(EST), Monday - Friday.
REPLACEMENT PARTS LIST
Part Description
ATop Piece
BBottom Piece
CTubular Shelves
DGlass Shelves
EShort Tubes
FMedium Tubes
GLong Tubes
HThin Interior
Tubes
IChrome Collars
J Top Caps
KBottom Caps
AA Threaded Inserts
BB Large Screws
CC Rubber Collars
Printed in China
CC
BB
AA
I
K
B
C
D
C
A
J
G
F
H
DE
F
H

IS9112-I4
ÉTAGÈRE MURALE EN
VERRE ET EN CHROME
ARTICLE #0045177
MODÈLE #9012SSMV
Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article
au détaillant, appelez notre service à la clientèle au 1 866 439-9800, entre 8 h et 20 h (HNE),
du lundi au vendredi.
Français p. 9
Español p. 17
allen + roth ® est une marquee de commerce
déposée de LF, LLC. Tous droits réservés.