Harbor Breeze E-TM52BNK5LED User manual

ECO BREEZE CEILING FAN
Harbor Breeze® is a registered trademark
of LF, LLC. All Rights Reserved.
E192641
LISTED
MODEL #E-TM52BNK5LED
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. -
5 p.m., EST, Friday.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
EB14593
1Lowes.com/harborbreeze
Español p. 19
ITEM #0062325

READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, install or operate the
product.
Safety Information .............................................................................................................. 2
Package Contents .............................................................................................................. 4
Hardware Contents ............................................................................................................ 5
Preparation ........................................................................................................................ 5
Initial Installation ................................................................................................................ 6
Fan Mounting ..................................................................................................................... 7
Wiring ................................................................................................................................. 9
Final Installation ................................................................................................................ 11
Operating Instructions ...................................................................................................... 14
Care and Maintenance ...................................................................................................... 16
Troubleshooting ................................................................................................................ 16
Limited Lifetime Warranty .................................................................................................. 17
Replacement Parts List ..................................................................................................... 18
TABLE OF CONTENTS
2
Lowes.com/harborbreeze
SAFETY INFORMATION
• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for
repairs, it must be shipped in its original packaging to ensure proper protection against damage
that might exceed the initial cause for return.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical
Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring
handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to
the floor and at least 30 in. from the end of the blades to any obstruction.
• After you install the fan, make sure all connections are secure to prevent the fan from falling.
• The net weight of this fan including the light kit is: 24.53 lbs.

SAFETY INFORMATION
WARNING
3Lowes.com/harborbreeze
WARNING
To reduce the risk of fire, electrical shock or personal injury, mount fan to outlet box
marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS. OR LESS" and use
mounting screws provided with the outlet box. Most outlet boxes commonly used for the
support of lighting fixtures are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box; do NOT use a
plastic outlet box. Secure the outlet box directly to the building structure. The outlet box and its
support must be able to support the moving weight of the fan (at least 35 lbs.).
To avoid personal injury, the use of gloves may be necessary while handling fan parts with
sharp edges.
To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan
are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your
house wire is larger than 12-gauge or there is more than one house wire to connect to the
corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.
To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed control
device or control fan speed with a full range dimmer switch.
To reduce the risk of fire, electrical shock or personal injury, do not bend the blade arms when
installing them, balancing the blades or cleaning the fan. Do not insert objects between the
rotating fan blades.
To reduce the risk of personal injury, use only parts provided with this fan. The use of parts
OTHER than those provided with this fan will void the warranty.
Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid
electrical shock.
Risk of Fire and Electric Shock: Do not repair or service this light kit. The light source is designed
for this specific application and can overheat if serviced by untrained personnel. If any servicing is
required, call our customer service department (at 1-800-643-0067) for return authorization and
shipping instructions.
WARNING
Be sure outlet box is properly grounded and that a ground wire (green or bare) is present.
Before beginning installation, carefully check all screws, bolts and nuts on fan motor assembly to
ensure that they are secured.
CAUTION

PACKAGE CONTENTS
F
KH
L
O
I
J
T
IMPORTANT REMINDER: You must use the
parts provided with this fan for proper installation
and safety.
A Downrod 1
B Canopy 1
C Mounting Bracket 1
D Yoke Cover 1
E Motor Housing 1
F Switch Housing Plate 1
G
Canopy Cover 1
H Glass Shade 1
I Blade Arm 5
J Blade 5
K Pull Chain Extension 2
L Light Kit Fitter 1
DESCRIPTIONPART QUANTITY
M Finial Plate (preassembled) 1
N
Finial (preassembled) 1
O
Pin (preassembled) 1
P Clip (preassembled)
1
Q
Motor Screw 10
(preassembled)
R Lock Washer 10
(preassembled)
S
Canopy Mounting Screw 2
(preassembled)
T Threaded Washer 1
(preassembled)
U Switch Housing Screw 3
(preassembled)
V Fitter Plate Screw 3
(preassembled)
DESCRIPTIONPART QUANTITY
4Lowes.com/harborbreeze
V
U
D
C
B
E
G
M
N
Q
P
R
S
A

5
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt
to assemble the product.
Estimated Assembly Time: 120 minutes
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety
Glasses, Stepladder and Wire Strippers
Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook and
Wire Cutters
DANGER: When using an existing outlet box, make sure the outlet box is securely attached to
the building structure and can support the full weight of the fan. Failure to do this can result in serious
injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan
after installation is complete.
CAUTION: Be sure outlet box is properly grounded and a ground wire (green or bare) is present.
After opening top of carton, remove mounting hardware package from foam inserts. Remove motor
from packing and place on carpet or on foam to avoid damage to finish.
CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure they are
secured.
PREPARATION
Lowes.com/harborbreeze
Fiber
Blade
Washer
Qty. 15
+ 1 extra
CC
Blade
Screw
Qty. 15
+ 1 extra
Wire
Connector
Qty. 4
AA BB CC
HARDWARE CONTENTS (shown actual size)

Turn off circuit breakers and wall switch to the fan
supply line leads.
DANGER: Failure to disconnect power supply
prior to installation may result in serious injury or
death.
1.
2.
Check to make sure blades (J) will be at least 30 in.
from any obstruction and at least 7 ft. above the
floor.
3.
6
Lowes.com/harborbreeze
J
ON
OFF
ON
OFF
3
2
1
A
B
7 ft.
min.
30 in.
min.
INITIAL INSTALLATION
Determine mounting method to use.
A. Standard mount
B. Angle mount
IMPORTANT: If using the angle mount, ensure the
ceiling angle is not steeper than 19°.
*Helpful Hint: Standard mounting is best suited for
ceilings 8 ft. high or higher. For taller ceilings you
may want to use a longer downrod (not included).
Angle mounting is best suited for angled or vaulted
ceilings. A longer downrod is sometimes necessary
to ensure proper blade clearance.

5.
Remove pin (O) and clip (P) from yoke at top of
motor housing (E) and partially loosen
preassembled set screws and nuts.
Remove motor screws (Q) and lock washers (R)
from underside of motor and save for blade arm
(I) attachment later on. [If there are plastic motor
blocks installed with the motor screws (Q) and
lock washers (R), discard the plastic motor
blocks.]
INITIAL INSTALLATION
Secure mounting bracket (C) to outlet box (not
included) using screws, spring washers and flat
washers provided with the outlet box.
*NOTE: It is very important you use the proper
hardware when installing the mounting bracket
(C) as this will support the fan.
IMPORTANT: If using the angle mount, make
sure open end of mounting bracket (C) is installed
facing the higher point of the ceiling.
4. 4
C
Q
R
5
FAN MOUNTING
7
Lowes.com/harborbreeze
1.
Set Screws
and Nuts
O
P
1
Yoke
E

FAN MOUNTING
2. Insert downrod (A) through canopy (B), canopy
cover (G) and yoke cover (D). [NOTE: Canopy
cover (G) must be turned with the smooth side
toward the motor housing (E).] Thread wires
from motor housing (E) through downrod (A).
Depending on the length of downrod you use,
you may need to cut the lead wires back to
simplify the wiring. If you decide to cut back the
lead wires, it is suggested you do so in the
following manner:
Take the lead wires and make sure you have
pulled them all the way through the top of the
downrod. Start at the TOP of the ball on the
downrod and measure 8 in. of lead wire, and
then cut the excess wire off with wire cutters (not
included).
NOTE: If you do not cut back the lead wires,
Steps 4 and 5 are not necessary and you may
proceed to Step 6 instead.
4.
3. Slip downrod (A) into yoke, align holes and
re-install pin (O) and clip (P). Tighten set screws
and then tighten nuts on the set screws. Slide
yoke cover (D) down until it rests on top of motor
housing (E).
8
Lowes.com/harborbreeze
Ball
4
2
3
A
Set Screws
and Nuts
O
A
P
E
D
G
A
B
D

FAN MOUNTING
9
Lowes.com/harborbreeze
WIRING
Install ball end of downrod (A) into mounting
bracket (C) opening. Align slot in ball with tab in
mounting bracket (C).
DANGER: Failure to align slot in ball with tab
may cause the fan to wobble or fall, which could
result in serious injury or death.
6.
If you decided to cut back the lead wires in Step 4,
strip a 1/2 in. of insulation from end of white wire.
Twist stripped ends of each strand of wire within
the insulation with pliers (not included). Repeat
Step 5 for black, blue (if applicable) and green
wires.
5. 5
Hanging
Ball Slot
Tab
6
A
C
WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors
provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from
the fan. If your house wire is larger than 12-gauge or there is more than one house wire to connect to
the two fan lead wires, consult an electrician for the proper size wire connectors to use.
CAUTION: Be sure outlet box is properly grounded and a ground (green or bare) wire is present.
WARNING: If house wires are different colors than referred to in the following steps, stop
immediately. A professional electrician is recommended to determine wiring.
NOTE: This fan is remote control adaptable (remote control not included). If you choose to purchase
a remote control for use with the fan, be advised that the dimming function for the light will not be
operable. Dimming capability for this light is only possible by using wall controls that control the fan
and light separately, such as the WM-7WWL (not included).

1.
WIRING
10
Lowes.com/harborbreeze
Choose wiring diagram (Fig. 1A, Fig. 1B or Fig. 1C)
that fits your situation and make appropriate wiring
connections as follows: [IMPORTANT: For each wire
connection below, use one of the wire connectors
(CC), making sure to screw wire connector (CC) on in
a clockwise direction.]
1A. FAN AND LIGHT CONTROLLED BY PULL
CHAINS: Connect BLACK and BLUE wire from fan
to BLACK wire from ceiling. Connect WHITE wire
from fan to WHITE wire from ceiling. Connect all
GROUND (GREEN) wires together from fan (on
downrod (A) and mounting bracket (C)) to
BARE/GREEN wire from ceiling.
FAN AND LIGHT CONTROLLED BY TWO WALL SWITCHES
1A
FAN AND LIGHT CONTROLLED BY PULL CHAINS
BLACK(POWER)
WHITE(NEUTRAL)
BLACK
GROUND/GREEN (BARE)
WHITE
120V POWER
FROM CEILING
BLUE &
BLACK
GREEN
1C. FAN AND LIGHT CONTROLLED BY TWO
WALL SWITCHES: If you intend to control the fan
and light with separate wall switches, connect
BLACK wire from fan to BLACK wire from the
independent wall switch for the fan. Connect BLUE
wire from fan to the BLACK wire from the other
independent wall switch for the light. Connect
WHITE wire from fan to WHITE wire from ceiling.
Connect all GROUND (GREEN) wires together
from fan (on downrod (A) and mounting bracket (C))
to BARE/GREEN wire from ceiling.
NOTE: BLACK wire is hot power for fan. BLUE wire
is hot power for light kit. WHITE wire is common for
fan and light kit. BARE/GREEN wire is ground.
1B. FAN CONTROLLED BY PULL CHAIN, LIGHT
BY WALL SWITCH: If you intend to control the fan
light with a separate wall switch, connect BLACK
wire from fan to BLACK wire from ceiling. Connect
BLUE wire from fan to the BLACK wire from the
independent wall switch for the light. Connect
WHITE wire from fan to WHITE wire from ceiling.
Connect all GROUND (GREEN) wires together
from fan (on downrod (A) and mounting bracket (C))
to BARE/GREEN wire from ceiling.
FAN AND LIGHT CONTROLLED BY TWO WALL SWITCHES
FAN AND LIGHT CONTROLLED BY TWO WALL SWITCHES
1C
120V POWER
FROM CEILING
BLACK
BLACK
(WALL
SWITCH)
BLUE
WHITE
BLACK(POWER)
WHITE(NEUTRAL)
GROUND/GREEN (BARE)
GREEN
BLACK
FAN AND LIGHT CONTROLLED BY TWO WALL SWITCHES
120V POWER
FROM CEILING
BLACK
BLACK
(WALL
SWITCH)
BLUE
WHITE
BLACK(POWER)
WHITE(NEUTRAL)
GROUND/GREEN (BARE)
GREEN
BLACK
1B
FAN CONTROLLED BY PULL CHAIN, LIGHT BY WALL SWITCH