Harbor Breeze FWH60BNK3LRS User manual

FAIRWIND HUGGER
LED CEILING FAN
ITEM #1596996
MODEL #FWH60BNK3LRS
Purchase Date
1
Español p. 18
APPROVED FOR USE IN
DAMP LOCATIONS
ATTACH YOUR RECEIPT HERE
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-527-1292, 8:30 a.m. - 5 p.m., CST, Monday - Friday.

Safety Information ................................................................................................................2
Package Contents ................................................................................................................4
Hardware Contents
......................................................................................................................... . . 5
Preparation ........................................................................................................................... 5
Initial Installation .................................................................................................................. . .5
Wiring ....................................................................................................................................7
Final Installation ................................................................................................................. . .. 9
Operating Instructions ..................................................................................................... . .13
Care and Maintenance ...................................................................................................... . .16
Troubleshooting...................................................................................................................16
Limited Lifetime Warranty .................................................................................................. . .17
Replacement Parts List .......................................................................................................17
TABLE OF CONTENTS
2
DANGER
When using an existing outlet box, make sure the outlet box is securely attached to the building
structure and can support the full weight of the fan. Failure to do this can result in serious injury or
death. The stability of the outlet box is essential in minimizing wobble and noise in the fan after
installation is complete.
To reduce the risk of serious bodily injury, DO NOT use power tools to assemble any part of the
fan, including the blades.
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for
repairs, it must be shipped in its original packaging to ensure proper protection against damage that
might exceed the initial cause for return.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical
Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring
handbook, available at Lowe's, if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to the
floor and at least 30 in. from the end of the blades to any obstruction.
• After you install the fan, make sure all connections are secure to prevent the fan from falling.
• The net weight of this fan including the light kit is: 20.29 lbs.

SAFETY INFORMATION
3
WARNING
To reduce the risk of fire, electrical shock or personal injury, mount fan to outlet box
marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS. OR LESS" and use
mounting screws provided with the outlet box. Most outlet boxes commonly used for the
support of lighting fixtures are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box; do NOT use a
plastic outlet box. Secure the outlet box directly to the building structure. The outlet box and its
support must be able to support the moving weight of the fan (at least 35 lbs.).
To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp
edges.
To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this
fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If
your house wire is larger than 12-gauge or there is more than one house wire to connect to the
corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.
To reduce the risk of fire or electrical shock, do not use the fan with any solid-state speed control
device or control fan speed with a full range dimmer switch.
To reduce the risk of fire, electrical shock or personal injury, do not bend the blades when
installing or balancing them, or cleaning the fan. Do not insert objects between the rotating fan
blades.
To reduce the risk of personal injury, use only parts provided with this fan. The use of parts
OTHER than those provided with this fan will void the warranty.
Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to
avoid electrical shock.
WARNING
Be sure outlet box is properly grounded and that a ground wire (green or bare) is present.
Before beginning installation, carefully check all screws, bolts and nuts on fan motor assembly to
ensure that they are secured.
Do NOT tamper with or attempt to repair LED component. The light source is designed for this
specific application and should not be serviced by untrained personnel. If any servicing is
required, call our customer service department.
CAUTION

IMPORTANT REMINDER: You must use the
parts provided with this fan for proper installation
and safety.
A Mounting Plate 1
B Mounting Plate Screw/Washer 4
(preassembled)
C Ring 1
D Motor Housing 1
E Motor Plate Screw 3
(preassembled)
F Fitter Plate 1
DESCRIPTIONPART QUANTITY
PACKAGE CONTENTS
4
DESCRIPTIONPART QUANTITY
G LED Light Kit 1
H Shade 1
I Blade 3
J Blade Plate 3
K Fitter Plate Screw 3
(preassembled)
L Remote Pack 1
M Remote Control Receiver 1
A
D
B
F
C
M
L
K
J
I
E
H
G

5
PREPARATION
HARDWARE CONTENTS (shown actual size)
Before beginning assembly of product, make sure all parts are present. Place motor on carpet or on
foam to avoid damage to finish. Compare parts with package contents list and hardware contents list. If
any part is missing or damaged, do not attempt to install, operate or assemble the product.
Estimated Assembly Time: 120 minutes
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers
Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook and Wire
Cutters
Wire
Connector
Qty. 3
+ 1 extra
AA
Motor
Screw/Washer
Qty. 6
+ 1 extra
BB
INITIAL INSTALLATION
Turn off circuit breakers or fuse and wall switch to
the fan supply line leads.
DANGER: Failure to disconnect power supply
prior to installation may result in serious injury or
death.
1.
ON
OFF
ON
OFF
1

6
INITIAL INSTALLATION
This fan can be mounted as a flushmount on a
regular (no-slope) ceiling only.
Check to make sure blades (I) will be at least
30 inches from any obstruction and at least 7 ft.
above the floor.
2.
Remove mounting plate screw/washer (B) on
outer edge of mounting plate (A) that is closest
to the J-hook. Remove mounting plate
screw/washer (B) on outer edge of mounting
plate (A) directly opposite the one was just
removed. Partially loosen the other two
mounting plate screw/washers (B). Save
mounting plate screw/washers (B) for later use.
3.
Secure mounting plate (A) to outlet box using
screws, spring washers, and flat washers provided
with the outlet box.
*NOTE: It is very important you use the proper
hardware when installing the mounting plate (A) as
this will support the fan.
Pull electrical wiring from outlet box through center
hole in the mounting plate (A).
4.
3
J-Hook
A
B
B
A
4
2
7 ft.
min.
30 in.
min.
I

INITIAL INSTALLATION
7
With wider opening facing up, place ring (C)
over top of motor housing (D). Allow ring (C)
to rest on top of motor, proceed to step 6.
5.
Lift motor housing (D) to mounting plate (A). Hang
motor housing (D) on J-hook on underside of
mounting plate (A). [IMPORTANT: Use one of the
non-slotted holes on the rim of the motor housing
to do so.]
This will allow motor housing (D) to hang out of the
way while wiring.
6.
WIRING
WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors provided
with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If
your house wire is larger than 12-gauge or there is more than one house wire to connect to the
corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.
CAUTION: Be sure outlet box is properly grounded and that a ground (green or bare) wire is
present.
WARNING: If house wires are different colors than referred to in the following steps, stop
immediately. A professional electrician is recommended to determine wiring.
WARNING: Using a full range dimmer switch (not included) to control fan speed will cause a loud
humming noise from fan. To reduce the risk of fire or electrical shock, do NOT use a full range dimmer
switch to control fan speed.
5
D
C
6
Non-slotted
Hole
J-Hook
D
A

8
WIRING
1.
Wire Connector x 3
Hardware Used
AA
Make the necessary wiring connections for
remote control operation as detailed below and
in the figure. For each wire connection, use one
of the wire connectors (AA), (L), making sure to
screw wire connector on in a clockwise
direction.
CAUTION: Assistance from another person is
recommended for this step.
Connect all GROUND (GREEN) wires together
from fan and mounting plate (A) to
BARE/GREEN supply wire from ceiling.
Connect BLACK wire (labeled AC IN L) from
remote control receiver (M) to BLACK supply
wire from ceiling.
Connect WHITE wire (labeled AC IN N) from
remote control receiver (M) to WHITE supply
wire from ceiling.
Connect WHITE wire (labeled TO MOTOR N)
from remote control receiver (M) to WHITE wire
from motor housing (D).
Connect BLACK wire (labeled TO MOTOR L)
from remote control receiver (M) to BLACK wire
from motor housing (D).
Connect BLUE wire (labeled FOR LIGHT) from
remote control receiver (M) to BLUE wire from
motor housing (D).
Wrap electrical tape around each individual wire
connector (AA), (L) down to the wire.
WARNING: Make sure no bare wire or wire
strands are visible after making connections.
Place green and white connections on opposite
side of box from the black and blue (if applicable)
connections.
Turn spliced/taped wires upward and gently push
wires and wire connectors into outlet box.
2.
2
AA
AA
AA
M
1WHITE SUPPLY WIRE
BLACK SUPPLY WIRE
BLACK
BLACK
WHITE
BLUE
BLUE
WHITE
BLACK
AC IN L
WHITE
AC IN N
WHITE
GROUND (GREEN OR BARE)
GROUND
(GREEN OR BARE)
BLACK
FROM
RECEIVER
FROM
FAN
FROM
RECEIVER
FROM
CEILING

9
1
Remove motor housing (D) from J-hook. Gently slide
remote control receiver (M) flat-side up into top of
motor housing (D), pushing wires, wire connectors
and antenna within.
NOTE: The remote control included with this fan
meets the following requirements:
a. Electrical rating: 120V / 60 Hz;
motor amps:1.00 MAX.
b. MAX light watts: 190W (incandescent, CFL
or LED bulbs.)
Should you choose to use a different remote control
with this fan, it must also meet these same
requirements.
1.
FINAL INSTALLATION
Raise ring (C) and align tabs on ring (C) with
grooves on motor housing (D) until you hear tabs
snap into grooves.
NOTE: Ring (C) should fit flush to ceiling when
done correctly.
Slide motor housing (D) over mounting plate (A),
aligning slotted holes in motor housing (D) with
loosened mounting plate screw/washers (B) in
mounting plate (A). Twist motor housing (D) to lock.
Re-insert the other two mounting plate
screws/washers (B) previously removed (Step 3,
page 6). Tighten all mounting plate screw/washers
(B) securely.
2.
3.
Tab
Grooves
Antenna
D
M
A
2
D
B
3
C
D

CAUTION: To reduce the risk of serious bodily injury,
DO NOT use power tools to assemble the blades (I). If
overtightened, blades (I) may crack and break.
Place one blade plate (J) under blade (I), aligning
holes. Then, insert one motor screw/washer (BB) into
one of the holes at the end of the blade (I), turning until
the motor screw/washer (BB) comes through the other
side of the blade (I). Repeat with the other motor
screw/washer (BB).
Align the protruding ends of the motor screw/washers
(BB) with the corresponding holes on the underside of
the motor housing (D). Tighten both motor screws/
washers (BB).
Repeat for the other two blades (I).
NOTE: Make sure all blades (I) are completely
secure before proceeding.
10
Hardware Used
Blade Screw/Washer x 6
BB
4.
5. Remove one motor plate screw (E) from motor
plate on underside of motor housing (D) and
partially loosen the other two motor plate screws
(E). Align slotted holes in fitter plate (F) with
loosened motor plate screws, allowing molex
connections from motor housing (D) to come
through hole in fitter plate (F). Twist fitter plate (F)
to lock. Re-insert the motor plate screw (E) that
was removed and securely tighten all three motor
plate screws (E).
5
FINAL INSTALLATION
4
I
D
J
BB
D
E
E
F
Molex
Connections