Harbor Breeze L1901 User manual

ITEM #0807420
MODEL #L1901
LYNSTEAD CEILING FAN
Harbor Breeze®is a registered trademark
of LF, LLC. All Rights Reserved.
1
Español p. 17
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday,
p.m., EST, Friday.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
PH19238
8 a.m. - 5

TABLE OF CONTENTS
2
Preparation .......................................................................................................................
Initial Installation Instructions ...........................................................................................
Wiring Instructions ............................................................................................................
Final Installation Instructions ............................................................................................
Operation Instructions ......................................................................................................
Care and Maintenance .....................................................................................................
Troubleshooting ...............................................................................................................
Limited Lifetime Warranty ...............................................................................................
Replacement Part List ......................................................................................................
Safety Information ............................................................................................................ 4
Package Contents ............................................................................................................
Hardware Contents ...................................................................................... ...................
3
4
5
6
8
9
13
13
14
15
16

PACKAGE CONTENTS
A1
1
1
1
B
C
D
Mounting Bracket
Motor Body
Mounting Plate
(Preassembled to motor
body (B))
3
PART DESCRIPTION QUANTITY
4N
3O
3P
1Q
1R
1S
Hex Nut
(Preassembled on
Mounting Bracket (A))
Metal Washer
(Preassembled on
Mounting Bracket (A))
Mounting Screw
(Preassembled on Switch
Housing Plate(C))
Light Kit Mounting Screw
(Preassembled on Switch
Housing (G))
Silicone Washer
(Preassembled on Light
Kit (H))
Metal Washer
(Preassembled on Light
Kit (H))
Manual Nut
(Preassembled on Light
Kit (H))
Finial
Finial Cap
Motor Housing 5
5
1
F
G
E
Switch Housing
Blade
Blade Iron
1
1
I
HGlass Bowl
Light Kit
2J 1K 1L
4M
Bulb
A
B
C
D
E
H
G
F
I
N
M
O
P
Q
R
K
LS
J
PART DESCRIPTION QUANTITY

Wire Nut
Qty. 4 Blade Screw
Qty. 15 + 1 extra Motor Screw
Qty. 10 + 1 extra Fob
Qty. 2
4
HARDWARE CONTENTS
SAFETY INFORMATION
(not shown actual size)
AA BB CC DD
READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, operate or install the product.
. All electrical connections must comply with local codes, ordinances or the National Electric Code (NEC).
Contact your municipal building department to inquire about your local codes, permits and/or inspections.
. Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse
or by switching off circuit breaker.
. Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
Never use a fixture in a two-wire system that is not grounded.
. If you are not sure your lighting system has a grounding means, do not attempt to install this fixture. Contact
a qualified, licensed electrician for information regarding proper grounding methods as required by the local
electrical code in your area.
. Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to the floor
and at least 30 in. from the ends of the blades to any obstruction.
. If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type
and electrical rating required.
. The lighting fixture must be positioned so there is at least 1.64 ft. between the bulb and any illuminated
surface.
. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be
connected to a grounded conductor power supply. If the conductor of a fan is identified as an ungrounded
conductor, then it should be connected to an ungrounded conductor power supply. If the conductor of a fan
is identified for equipment grounding, then it should be connected to an equipment-grounding conductor.
. Installing a fixture into an electrical system without a proper grounding means could allow metal parts of the
fixture to carry electrical currents. If any of the fixture wires, wire connections or splices are broken, cut or
loose during the mounting or normal operation of the fixture, under such conditon, anyone coming in contact
with the fixture is subject to electrical shock, which could cause serious injury or death.
. Connection of the bare or green fixture ground wire to the black or white house wires may allow metal parts
of the fixture to carry electrical currents. Under this condition anyone coming in contact with the fixture will
receive electrical shock, which could cause serious injury or death.
. Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires
to have contact with any surface having a sharp edge. Doing so may damage or cut the wire insulation,
which could cause serious injury or death from electric shock.
DANGER

5
WARNING
CAUTION
PREPARATION
Estimated Assembly Time:
and Wrench.

6
INITIAL INSTALLATION INSTRUCTIONS
This fan was designed to be mounted only on flat
ceilings and can be used on ceilings less than 8 feet
high (blades should be a minimum of 7 feet from the
floor. It is requred at least 30 inch from blade tip to
nearest wall or obstruction).
Fan mounting options:
2..
2
3
1
7 ft. MIN.
30 IN.
MIN.
DANGER: Failure to disconnect power supply prior to
1. Turn off circuit breakers and wall switch to the fan supply
line leads.
installation may result in serious injury or death.
or
T
Turn Off Power Source
3. Check existing outlet box (not included) to ensure it is
securely fastened to at least two points in a structural
ceiling member and can support the full weight of the fan.
Once verified, install mounting bracket (A) to the outlet
box using the screws and washers provided with the
outlet box.
DANGER: A loose outlet box can cause the fan to
wobble and increase the fan’s potential to fall, which
could result in serious injury or death.
A

7
4. Remove the hex nuts (M) and metal washers (N) from
the threaded rods on the mounting bracket (A). Hang
the motor body (B) onto the hook from the mounting
bracket (A). This will allow for hands-free wiring.
INITIAL INSTALLATION INSTRUCTIONS
A
NM
B
4

8
WIRING INSTRUCTIONS
1. Make wire connections as in the wiring diagram.
Connect BLACK and BLUE wires from fan to BLACK
(live) wire from house.
Connect WHITE wire from fan to WHITE (Neutral) wire
from house.
Connect GREEN (GROUND) wires from mounting
bracket (A) and motor body (B) to GREEN (GROUND)
from house.
1
GREEN(GROUND)
BLACK
WHITE
GREEN
(GROUND)
WHITE
BLACK
BLUE
AA
Hardware Used
Wire Connector x 3
2. Wrap electrical tape (not included) around each wire
connector and make sure no bare wire or wire strands
are visible after making connections. Then, turn wires
upward and carefully push them into the outlet box;
make sure the WHITE and GREEN connections are on
one side and the BLACK connections are on the other
side.
WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse
box before hanging.
WARNING: If you are not sure if the outlet box is grounded, contact a licensed electrician for
advice, as it must be grounded for safe operation.
WARNING: If house wires are different colors than referred to in the following steps, stop
immediately. A professional electrician is recommended to determine proper wiring.
WARNING: If you feel that you do not have enough electrical wiring knowledge or experience,
have your fan installed by a licensed electrician.
AA
2

1. Lift the motor body (B) onto the mounting bracket (A),
making sure not to break away any wire connections,
and allow the four threaded rods from the mounting
bracket (A) to insert into rubber grommets on the
motor bracket from the motor body (B). Attach the
hanger bracket to mounting bracket (A) using the
metal washers (N) and hex nuts (M) removed
previously. Tighten the hex nuts with a wrench (not
included).
2. Raise the motor housing (D) up, align the four dot
labels on the motor housing (D) with the mounting
bracket (A), place the mounting bracket (A) onto the
recesses on the motor housing (D) properly, then
rotate the motor housing (D) clockwise until the
mounting bracket (A) slide into the slot hole inside the
motor housing (D).
9
FINAL INSTALLATION INSTRUCTIONS
Motor Bracket
Recesses
Recesses
dot label
A
A
A
D
B
N
M
11
2
3. Position blade iron (E) under blade (F). Secure them
with three blade screws (BB). Do not tighten blade
screws (BB) until three are in place. Then, tighten
each blade screw (BB) starting with the center blade
screw (BB). Repeat for all blade assemblies.
Hardware Used
x 15
BB
Blade Screw
3
BB
F
E

10
4. Align the holes between the blade iron (E) and motor.
Install the blade assembly to the motor using motor
screws (CC), and partially tighten. Repeat for the
remaining blade assemblies. Securely tighten all motor
screws (CC).
5. Remove one of the mounting screws (O) preinstalled
on the mounting plate (C) and loosen (do not remove)
the other two. Insert the wires from the motor body (B)
through the center hole in the switch housing (G).
Attach the switch housing (G) to the mounting plate (C)
by placing the keyslot holes from the switch
housing (G) onto the two protruding screw heads on
the mounting plate (C). Twist the switch housing (G)
until the screw heads engage the keyslots. Install
mounting screws (O) into the closed hole in the switch
housing (G). Tighten all mounting screws (O) to
complete attachment of the switch housing (G).
Hardware Used
x 10
CC
Motor Screw
6. Remove the three screws (P) preinstalled on the
switch housing (G). Attach the connector from the
light kit (H) to the connector from the motor body.
Align the three holes between the light kit (H) and
the switch housing (G). Re-install the switch housing
screws (P) to attach the light kit (H) to the switch
housing (G).
4
E
Motor
5
O
G
C
G
B
6
FINAL INSTALLATION INSTRUCTIONS
CC
PH