Harbor Breeze HTD20005 User manual

ITEM #2599777
MODEL #HTD20005
KENTON CEILING FAN
Harbor Breeze®is a registered trademark
of LF, LLC. All Rights Reserved.
1
Español p. 18
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 8 p.m., EST, Monday - Sunday.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
VR20245

TABLE OF CONTENTS
2
Preparation .......................................................................................................................
Initial Installation Instructions ...........................................................................................
Wiring Instructions ............................................................................................................
Final Installation Instructions ............................................................................................
Operation Instructions ......................................................................................................
Care and Maintenance .....................................................................................................
Troubleshooting ...............................................................................................................
Limited Lifetime Warranty ...............................................................................................
FCC Warning ……………..................................................................................................
Safety Information ............................................................................................................ 4
Package Contents ............................................................................................................
Hardware Contents ...................................................................................... ...................
3
4
5
6
8
9
11
13
14
15
16
Replacement Part List ...................................................................................................... 17

PACKAGE CONTENTS
1A Ceiling Plate
1B Motor Assembly
1C Switch Housing
3D Blade
1E Light Kit
1F Bowl
1G Remote Unit
3
PART DESCRIPTION QUANTITY
1H Trim Ring [Preassembled
on Motor Assembly (B)]
4I
Mounting Screw
[Preassembled on Motor
Assembly (B )]
3J
Mounting Plate Screw
[Preassembled on Motor
Assembly (B )]
3K
Switch Housing Screw
[Preassembled on Switch
Housing (C )]
A
K
C
BE
F
D
G
I
H
J
PART DESCRIPTION QUANTITY
X2X6
CR2032 3V

Blade Screw
Qty 12+1 extra
4
HARDWARE CONTENTS
SAFETY INFORMATION
(not shown actual size)
AA
READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, operate or install the product.
. All electrical connections must comply with local codes, ordinances or the National Electric Code (NEC).
Contact your municipal building department to inquire about your local codes, permits and/or inspections.
. Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse
or by switching off circuit breaker.
. Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
Never use a fixture in a two-wire system that is not grounded.
. If you are not sure your lighting system has a grounding means, do not attempt to install this fixture. Contact
a qualified, licensed electrician for information regarding proper grounding methods as required by the local
electrical code in your area.
. Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to the floor
and at least 30 in. from the ends of the blades to any obstruction.
. If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type
and electrical rating required.
. The lighting fixture must be positioned so there is at least 1.64 ft. between the bulb and any illuminated
surface.
. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be
connected to a grounded conductor power supply. If the conductor of a fan is identified as an ungrounded
conductor, then it should be connected to an ungrounded conductor power supply. If the conductor of a fan
is identified for equipment grounding, then it should be connected to an equipment-grounding conductor.
. Installing a fixture into an electrical system without a proper grounding means could allow metal parts of the
fixture to carry electrical currents. If any of the fixture wires, wire connections or splices are broken, cut or
loose during the mounting or normal operation of the fixture, under such conditon, anyone coming in contact
with the fixture is subject to electrical shock, which could cause serious injury or death.
. Connection of the bare or green fixture ground wire to the black or white house wires may allow metal parts
of the fixture to carry electrical currents. Under this condition anyone coming in contact with the fixture will
receive electrical shock, which could cause serious injury or death.
. Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires
to have contact with any surface having a sharp edge. Doing so may damage or cut the wire insulation,
which could cause serious injury or death from electric shock.
DANGER

5
WARNING
CAUTION
PREPARATION
Estimated Assembly Time:
and Wrench.
Chemical Burn Hazard. Keep batteries away from children. This remote contains a lithium button cell battery.
If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal
burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the
battery compartment does not close securely, stop using the product, remove the batteries, and keep it away
from children. If you think batteries might have been swallowed or placed inside any part of the body, seek
immediate medical attention.
Dispose of cells properly and keep away from children. Even used cells may cause injury.

6
INITIAL INSTALLATION INSTRUCTIONS
This fan was designed to be mounted only on flat
ceilings and can be used on ceilings less than 9 feet
high (blades should be a minimum of 7 feet from the
floor. It is requred at least 30 inch from blade tip to
nearest wall or obstruction).
Fan mounting option:
2..
2
3
1
7 ft. MIN.
30 IN.
MIN.
DANGER: Failure to disconnect power supply prior to
1. Turn off circuit breakers and wall switch to the fan supply
line leads.
installation may result in serious injury or death.
or
T
Turn Off Power Source
3. Check existing outlet box (not included) to ensure it is
securely fastened to at least two points in a structural
ceiling member and can support the full weight of the
fan.Once verified, install ceiling plate (A) to the outlet
box using the screws and washers provided with the
outlet box.
DANGER: A loose outlet box can cause the fan to
wobble and increase the fan’s potential to fall, which
could result in serious injury or death.
A

7
4.Partially remove two diagonal mounting screws (I) on
the round holes, keep for later use. And loosen the
other two screws (I).
5.Hang the motor assembly (B) onto the hook from the
ceiling plate (A). This will allow for hands-free wiring.
INITIAL INSTALLATION INSTRUCTIONS
I
B
I
B
A
4
5

8
WIRING INSTRUCTIONS
1
Hardware Used
Wire Connector x 6
2. Wrap electrical tape (not included) around each wire
connector and make sure no bare wire or wire strands
are visible after making connections. Then, turn wires
upward and carefully push them into the outlet box;
make sure the WHITE and GREEN connections are on
one side and the BLACK connections are on the other
side.
WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse
box before hanging.
WARNING: If you are not sure if the outlet box is grounded, contact a licensed electrician for
advice, as it must be grounded for safe operation.
WARNING: If house wires are different colors than referred to in the following steps, stop
immediately. A professional electrician is recommended to determine proper wiring.
WARNING: If you feel that you do not have enough electrical wiring knowledge or experience,
have your fan installed by a licensed electrician.
2
1. Follow steps below to wiring your fan, once wiring step
has been completed, slide the wired receiver into the
motor assembly (B) with the flat side of the receiver
facing the ceiling.
TO MOTOR N from the receiver.
FOR LIGHT from the receiver.
TO MOTOR L from the receiver.
marked AC IN L from the receiver.
marked AC IN N from the receiver.
Connect GROUND (GREEN) wires from ceiling plate
and fan assembly, to GROUND (GREEN or BARE
COPPER) from house.

1. After wire connections, take the motor assembly (B)
off the hook.Raise the motor assembly (B) up to the
ceiling plate (A).Align two remained screws (I) on the
motor assembly (B) to the keyholes on the ceiling
plate (A), rotate clockwise until the screw heads
engage the keyhole slots fully. Make sure not to
break any wire connections.
2. Re-install two mounting screws (I) to the round holes,
securely tighten four (4) mounting screws (I).
9
FINAL INSTALLATION INSTRUCTIONS
11
2
A
A
I
I
B
3. Lift the trim ring (H) up, aligning four notches on the
canopy of motor assembly (B) with raised areas on the
inner side of trim ring (H) and pop it into the canopy.
3
Canopy
A
H

10
4. Insert blade (D) through slot on fan motor assembly
(B), align with four screws holes, securely tighten
with blade screws (AA). Repeat for remaining blades.
Hardware Used
x 12
AA
Blade Screw
5. Remove one of the mounting screws (J) on the
mounting plate of motor assembly (B) and keep for
later use. And loosen the other two.
4
B
AA
D
5
FINAL INSTALLATION INSTRUCTIONS
B
J
6
. Insert the 9 pin connector from the motor assembly (B)
through the center hole in the switch housing (C).
Attach the switch housing (C) to the mounting plate on
the motor assembly (B) by placing the keyhole slots
from the switch housing (C) onto the two protruding
mounting screws (J ) heads. Adjust the switch housing
(C) until the screw heads are aligned with the keyholes,
then re-insert mounting screw (J) previously removed
on step 5. Tighten all mounting screws (J) securely.
Mounting Plate
Mounting
Plate
6
C
J
B