Harbor Breeze C-TR56BNK3D1R User manual

ITEM #0835144
BRIDGEWATER CEILING FAN
MODEL #C-TR56BNK3D1R
ATTACH YOUR RECEIPT HERE
Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m.,
EST, Friday.
1
Harbor Breeze® is a registered trademark
of LF, LLC. All Rights Reserved.
AB1801
Français p. 19
4009654

2
Safety Information ...............................................................................................................
. . 2
Package Contents ..............................................................................................................
. .. 4
Hardware Contents
............................................................................................................................ 5
Preparation ............................................................................................................................ 5
Initial Installation ................................................................................................................... 5
Installing Safety Cable ........................................................................................................
. .10
Wiring ...................................................................................................................................11
Final Installation .................................................................................................................. 13
Operating Instructions ......................................................................................................... 15
Care and Maintenance ...................................................................................................
. .... 16
Troubleshooting .................................................................................................................... 17
Limited Lifetime Warranty .................................................................................................... 18
Replacement Parts List ....................................................................................................... 18
TABLE OF CONTENTS
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for
repairs, it must be shipped in its original packaging to ensure proper protection against damage
that might exceed the initial cause for return.
• Make sure all electrical connections comply with local codes, ordinances, the Canadian Electrical
Code and ANSI/NFPA 70-1999. Hire a qualified electrician.
• Make sure the installation site you choose allows a minimum clearance of 10 ft. from the blades to
the floor and at least 30 in. from the end of the blades to any obstruction.
• After you install the fan, make sure all connections are secure to prevent the fan from falling.
• The net weight of this fan is: 24.53 lbs.
To reduce the risk of fire, electrical shock or personal injury, mount fan to outlet box
marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS. (15.9 KG) OR LESS" and
use mounting screws provided with the outlet box. Most outlet boxes commonly used
for the support of lighting fixtures are not acceptable for fan support and may need to
be replaced.
WARNING

SAFETY INFORMATION
3
WARNING
When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box; do NOT use a
plastic outlet box. Secure the outlet box directly to the building structure. The outlet box and its
support must be able to support the moving weight of the fan (at least 35 lbs.).
To avoid personal injury, the use of gloves may be necessary while handling fan parts with
sharp edges.
To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan
are designed to accept only one 12-gauge house wire and two lead wires from the fan.
To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed control
device or control fan speed with a full range dimmer switch.
To reduce the risk of fire, electrical shock or personal injury, do not insert objects between the
rotating fan blades.
To reduce the risk of personal injury, use only parts provided with this fan. The use of parts
OTHER than those provided with this fan will void the warranty.
This fan MUST be installed with the safety cable provided with the fan. Failure to use the safety
cable provided may result in personal injury, damage to the fan or damage to other property.
Before installation, be sure to shut off electricity at main switch or circuit breaker in order to avoid
electrical shock.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
Be sure outlet box is properly grounded and that a ground wire (green or bare) is present.
Before beginning installation, carefully check all screws, bolts and nuts on fan motor assembly to
ensure they are secured.
CAUTION
NOTE: Dimmable to 10% with select dimmers. See Lowes.com for more information.

PACKAGE CONTENTS
4
4
IMPORTANT REMINDER: You must use the
parts provided with this fan for proper installation
and safety.
A Downrod 1
B Canopy 1
C Mounting Bracket 1
(preassembled)
D Motor Housing 1
E
Yoke Cover 1
F Canopy Mounting Washer 4
(preassembled)
G
Canopy Mounting Screw 4
(preassembled)
H Motor Screw 6 + 1
(preassembled)
DESCRIPTIONPART QUANTITY DESCRIPTIONPART QUANTITY
I Lock Washer (preassembled) 6 + 1
J Flat Washer (preassembled) 6 + 1
K LED Light Kit 1
L Pin (preassembled) 1
M Clip (preassembled) 1
N Blade 3
O Remote Control Receiver 1
P Remote Pack
1
Q Vice (preassembled) 1
R
Safety Cable 1
(preassembled)
S Fitter Plate Screw 2
(preassembled)
T Glass Shade 1
A
D
B
F
C
M
L
J
I
E
O
H
G
N
P
Q
R
S
T
K

5
HARDWARE CONTENTS (shown actual size)
Before beginning assembly of product, make sure all parts are present. Place motor on carpet or on
foam to avoid damage to finish. Compare parts with package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 120 minutes
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety
Glasses, Stepladder and Wire Strippers
Helpful Tools (not included): AC Tester Light, Tape Measure and Wire Cutters
PREPARATION
Wire
Connector
Qty. 4
AA
INITIAL INSTALLATION
ON
OFF
ON
OFF
1
Turn off circuit breakers and wall switch to the fan
supply line leads.
DANGER: Failure to disconnect power supply
prior to installation may result in serious injury or
death.
1.
Fitter Plate
Screw
Qty. 1
BB

INITIAL INSTALLATION
6
2.
Check to make sure blades (N) will be at least
30 in. from any obstruction and at least 10 ft.
above the floor.
3.
4. 4
Loosen two canopy mounting screws (G) and
canopy mounting washers (F) in slotted holes
of canopy (B) and remove the other two canopy
mounting screws (G) and canopy mounting
washers (F); save for later use.
Twist canopy (B) and remove mounting bracket
(C).
Determine mounting method to use.
A. Standard mount
B. Angle mount
Note: Flushmount and closemount options are not
available for this fan.
IMPORTANT: If using the angle mount, ensure the
ceiling angle is not steeper than 19°.
*Helpful Hint: Downrod-style mounting is best
suited for ceilings 10 ft. high or higher. For taller
ceilings you may want to use a longer downrod
(sold separately). Angle-style mounting is best
suited for angled or vaulted ceilings. A longer
downrod is sometimes necessary to ensure proper
blade clearance.
2
B
A
19° max.
G
10 ft.
min.
30 in.
min.
3
N
C
B
FG
F

INITIAL INSTALLATION
7
5. Remove 6 motor screws (H), 6 lock washers (I)
and 6 flat washers (J) from top of motor housing
(D).
Place one blade (N) on top of motor housing (D),
aligning holes in blade (N) with holes in motor
housing (D). Attach blade (N) with 2 motor screws
(H), lock washers (I) and flat washers (J). Tighten
motor screws (H) securely. Repeat for remaining
blades (N).
Note: Make sure to attach blade (N) with the angled
side of the blade facing down.
6.
7. 7
6
Secure mounting bracket (C) to outlet box (not
included) using screws, spring washers and flat
washers provided with the outlet box.
*NOTE: It is very important you use the proper
hardware when installing the mounting bracket
(C) as this will support the fan.
IMPORTANT: If using the angle mount, make
sure open end of mounting bracket (C) is
installed facing the higher point of the ceiling, and
ensure the ceiling angle is not steeper than 19°. Open End
C
C
ANGLE
MOUNT
STANDARD
MOUNT
D
Angled Side
of Blade
I
H
J
N
D
5
H
IH
J
H
H
(Top View)

Nut
Screw
Q
R
8
Remove pin (L) and clip (M) from downrod (A).
Partially loosen preassembled set screws and
nuts in yoke at top of motor housing (D).
9a.
9b.
10. 10
Insert downrod (A) through canopy (B) and yoke cover
(E). Thread wires and safety cable (R) from motor
housing (D) up through downrod (A).
B
A
E
D
9b
Yoke
Set Screw
& Nut
Side-view
9a
M
L
A
INITIAL INSTALLATION
Remove vice (Q) from safety cable (R)
preassembled to motor housing (D) by loosening
preassembled screw and nut on vice (Q).
8. 8
D

9
11. 11
Slip downrod (A) into yoke of motor housing (D),
align holes and re-install pin (L) and clip (M).
Tighten set screws and then tighten nuts. Slide
yoke cover (E) down until it rests on top of motor
housing (D). A
M
L
E
D
Set Screw
and Nut
12.
13.
Depending on the length of downrod you use, you
may need to cut the lead wires back to simplify the
wiring. If you decide to cut back the lead wires, it is
suggested you do so in the following manner:
Take the lead wires and make sure you have pulled
them all the way through the top of the downrod.
Start at the TOP of the hanging ball on the downrod
and measure 8 in. of lead wire, and then cut the
excess wire off with wire cutters (not included).
IMPORTANT: Do NOT cut safety cable (R).
NOTE: If you do not cut back the lead wires, Steps
12 and 13 are not necessary and you may
proceed to Step 14 instead.
If you cut back the lead wires in Step 12, strip 1/2
in. of insulation from end of each wire -- WHITE,
BLACK and BLUE. Twist stripped ends of each
strand of wire within the insulation with pliers (not
included).
13
12
Hanging
Ball
8 in.
A
INITIAL INSTALLATION

10
1. 1
Replace vice (Q) and adjust length of safety cable
(R), preassembled to motor housing (D), by
loosening screw and nut on the vice (Q) and pulling
on the safety cable (R). Adjust slack in safety cable
(R) to a hand’s length and re-tighten screw and nut
on vice (Q) securely. The loop at the end of the
safety cable (R) should just fit over the threads on
the wood screw (not included).
Test safety cable (R) by pulling on loose end with
pliers. If the safety cable (R) slips, then screw and
nut on vice (Q) must be set tighter.
Q
Screw
Nut
Loop
Wood
Screw
INSTALLING SAFETY CABLE
2. Find a secure attachment point (wood ceiling joist
recommended) and secure safety cable (R) using
a heavy-duty wood screw, washer and lock
washer (none included).
NOTE: Extra cable slack can be left in ceiling
area.
R
Wood Screw,
Washer and
Lock Washer
Wood
Joist
2
Loop
R
14. Install hanging ball of downrod (A) into opening of
mounting bracket (C). Align one of the slots in
hanging ball with the tab in mounting bracket (C).
DANGER: Failure to align slot in hanging ball
with the tab in mounting bracket (C) may result in
serious injury or death.
CAUTION: Assistance from another person is
recommended for this step.
C
Tab
14
A
Slot
INITIAL INSTALLATION