Harbor Breeze L1305 User manual

1
OCRACOKE CEILING FAN
ITEM #0451812
MODEL #L1305
Español p. 19
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday,
8 a.m. - 5 p.m., EST, Friday.
EB14428
ATTACH YOUR RECEIPT HERE
Lowes.com/harborbreeze
Harbor Breeze®is a registered trademark
of LF, LLC. All Rights Reserved.

2
TABLE OF CONTENTS
Package Contents...............................................................................................................
Hardware Contents.............................................................................................................
Safety Information...............................................................................................................
Preparation .........................................................................................................................
Initial Instructions ................................................................................................................
Standard/Angle-Mounting Instructions ................................................................................
Flushmount Instructions ......................................................................................................
Wiring Instructions ...............................................................................................................
Final Instructions .................................................................................................................
Operating Instructions ........................................................................................................
Care and Maintenance .......................................................................................................
Troubleshooting...................................................................................................................
Limited Lifetime Warranty....................................................................................................
Replacement Parts List ......................................................................................................
3
4
4
5
6
7
9
10
11
14
14
15
17
18
Lowes.com/harborbreeze

3
PACKAGE CONTENTS
Lowes.com/harborbreeze
ABE
O
K
N
M
F
D
C
J
I
S
R
Q
P
L
H
G
A Mounting Bracket 1 K Coupling
(preassembled on the Motor Housing (F))
1
B Downrod Assembly 1 L Mounting Bracket Screw
(preassembled on Mounting Bracket (A))
4
C Canopy 1 M Clevis Pin
(preassembled on Coupling (K)) 1
D
Canopy Cover
(preassembled on
Canopy (C))
1 N Hairpin Clip
(preassembled on Coupling (K)) 1
E Coupling Cover 1 O Coupling Screw
(preassembled on Coupling (K)) 2
F Motor Housing 1 P Balance Kit 1
G Blade Iron 5 Q Mounting Screw
(preassembled on Motor Housing (F)) 3
H Blade 5 R Switch Housing Screw
(preassembled on Switch Housing (I)) 3
I Switch Housing 1 S Motor Screw
(preassembled on the Motor Housing (F))
10
J Switch Cover 1
PART PARTDESCRIPTION QUANTITY QUANTITYDESCRIPTION

4
Lowes.com/harborbreeze
HARDWARE CONTENTS
SAFETY INFORMATION
(not shown actual size)
Wire Connector
Qty. 4
Blade Screw
Qty. 15 + 1 extra Fob
Qty. 1
Extra Motor Screw
Qty. 2
AA BB CC DD
READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, operate or install the product.
． All electrical connections must comply with local codes, ordinances or the National Electric Code (NEC).
Contact your municipal building department to inquire about your local codes, permits and/or inspections.
． Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse or
by removing th fuse or by switching off circuit breaker.
． Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
Never use a fixture in a two-wire system that is not grounded.
． If you are not sure your lighting system has a grounding means, do not attempt to install this fixture. Contact
a qualified, licensed electrician for information regarding proper grounding methods as required by the local
electrical code in your area.
． Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to the floor
and at least 30 in. from the ends of the blades to any obstruction.
． If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type
and electrical rating required.
． The lighting fixture must be positioned so there is at least 1.64 ft. between the bulb and any illuminated
surface.
． Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires
to have contact with any surface having a sharp edge. Doing so may damage or cut the wire insulation,
which could cause serious injury or death from electric shock.
． Connection of the bare or green fixture ground wire to the black or white house wires may allow metal parts
of the fixture to carry electrical currents. Under this condition anyone coming in contact with the fixture will
receive electrical shock, which could cause serious injury or death.
． Installing a fixture into an electrical system without a proper grounding means could allow metal parts of the
fixture to carry electrical currents. If any of the fixture wires, wire connections or splices are b ut or loose
during the mounting or normal operation of the fixture, under such conditon, anyone coming in contact with
the fixture is subject to electrical shock, which could cause serious injury or death.
． For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be
connected to a grounded conductor power supply. If the conductor of a fan is identified as an ungrounded
conductor, then it should be connected to an ungrounded conductor power supply. If the conductor of a fan
is identified for equipment grounding, then it should be connected to an equipment-grounding conductor.
DANGER

SAFETY INFORMATION
PREPARATION
WARNING
DANGER
5
Lowes.com/harborbreeze
. Risk of fire. Most dwellings built before 1985 have supply wire rated for 140°F. Consult a qualified
electrician before installation.
. Wire connectors will not support the weight of a fixture; suspending a fixture by the house wires
and wire connectors will result in the fixture falling, with the possibility of personal injury and the
danger of electrical shock or fire.
. To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed device
or variable speed control.
. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets,
balancing or cleaning the fan.
. Before servicing or cleaning the unit, switch power off at the service panel and lock the service
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
. Do not insert foreign objects in between rotating fan blades.
. Do not install or use the fan if any part is damaged or missing.
. Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not
permit wires to have contact with any surface having a sharp edge. Doing so may damage or cut
the wire insulation, which could cause serious injury or death from electric shock.
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble
the product.
Estimated Assembly Time: 45 minutes
Tools Required for Assembly (not inclueded): Philips Screwdriver, Step Ladder, Tape, Pliers and Wire
Cutters.
. Connection of the bare or green fixture ground wire to the black or white house wires may allow
metal parts of the fixture to carry electrical currents. Under this condition anyone coming in contact
with the fixture will receive electrical shock, which could cause serious injury or death.
. Installing a fixture into an electrical system without a proper grounding means could allow metal
parts of the fixture to carry electrical currents. If any of the fixture wires, wire connections or splices
are broken, cut or loose during the mounting or normal operation of the fixture, under such
conditon, anyone coming in contact with the fixture is subject to electrical shock, which could cause
serious injury or death.
. To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked
'ACCEPTABLE FOR FAN SUPPORT OF 35LBS OR LESS' and use mounting screws provided
with the outlet box and/or support directly from building structure. Most outlet boxes commonly
used for the support of luminaries are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.

INITIAL INSTRUCTIONS
6
Lowes.com/harborbreeze
1. Turn off circuit breakers and wall switch to the fan supply
line leads.
2a. Choose the desired mounting method:
A. Standard Mounting: Standard mounting is best
suited for ceilings 8 ft. or higher. For taller ceilings you
may want to use a longer downrod (not included).
B. Angle Mounting: Angle-style mounting is best suited
for angled or vaulted ceilings. A longer downrod is
sometimes necessary to ensure proper blade clearance.
If using the angle mount, make sure the ceiling angle is
not steeper than 20°.
C. Flush Mounting: Flushmount installation is used for
ceiling less than 8 feet high.
DANGER: Failure to disconnect power supply prior to
installation may result in serious injury of death.
1
OFF
OFF
ON
2a
AB
C
2b. It is required at least 30 inch from blade tip to nearest
wall or obstruction. Check downrod length to ensure 7
feet from bottom edge of blade to the floor.
7 ft. MIN.
30 in. MIN.
2b

7
Lowes.com/harborbreeze
INITIAL INSTRUCTIONS
4. Remove hairpin clip (N) and clevis pin (M) from the
coupling (K) on motor housing (F). Retain for later use.
Note: Make sure to keep loose hardware separate to
avoid confusion during installation.
Loosen the two coupling screws (O) in the coupling (K),
but do not remove them.
1. Place downrod assembly (B) through canopy (C), canopy
cover (D) and coupling cover (E). Then, feed power wires
from motor housing (F) through the downrod assembly (B).
STANDARD/ANGLE-MOUNTING INSTRUCTIONS
C
E
D
B
1
F
3. Check existing outlet box (not included) to ensure it is
securely fastened to at least two points in a structural
ceiling member and can support the full weight of the
fan. Once verified, install mounting bracket (A) to the
outlet box using the screws and washers provided with
the outlet box.
Note: If using the angel mount, make sure open end of
mounting bracket (A) is installed facing the higher point
of the ceiling.
DANGER: A loose outlet box can cause the fan to wobble
and increase the fan's potential to fall, which could result
in serious injury or death.
3
Open End
A
A
4
M
O
N
K
F
For STANDARD/ANGLE-MOUNTING INSTRUCTIONS,
proceed to Step 1 below. For FLUSHMOUNT
INSTRUCTIONS, skip to page 9.

8
Lowes.com/harborbreeze
Proceed to WIRING on page 10.
DANGER: Be careful when aligning the tab to the
notch! If not fully engaged, there is a possibility of the
fan falling, which may result in serious injury or death.
STANDARD/ANGLE-MOUNTING INSTRUCTIONS
3. Cut off excess fixture wires, leaving approximately 6 to
9 inches above the top of the downrod assembly (B).
Strip 1/2 inch of insulation from the end each fixture wire.
4. Carefully lift the assembly and rest the hanger ball of
downrod assembly (B) on the mounting bracket (A)
attached to the outlet box. Be sure the groove in the
hanger ball is lined up with the tab on the mounting
bracket (A). This will allow for hands-free wiring.
6 to 9 in.
3
2. Insert downrod assembly (B) into the coupling (K).
Align the hole on downrod assembly (B) to hole on
coupling (K), then re-install clevis pin (M). Re-attach
hairpin clip (N) into clevis pin (M) until it snaps into
place, then tighten the two previously loosened
coupling screws (O).
B
N
M
F
O
2
A
B
4
Hanger
Ball
Tab
Slot
CAUTION: Ensure all screws are tight before moving
onto the next step.

9
Lowes.com/harborbreeze
FLUSHMOUNT INSTRUCTIONS
3. Raise assembly and temporarily place one side of
canopy (C) onto hook of mounting bracket (A). This will
allow for hands-free wiring.
Proceed to WIRING below.
A
C
Hook
3
2. Remove the three preassembled Phillips head screws
near the coupling (K) on the motor housing (F). Save
them for future use. Guide motor wires through the base
of the canopy (C), then attach canopy (C) to motor
housing (F) with previously removed screws. Tighten
securely.
1. Remove canopy cover (D) by pressing out on the
inner edges of the canopy cover until it releases from
the canopy (C).
2
C
F
K
Screw
C
D
1
Note: Flushmount installation will not use canopy cover (D),
downrod assembly (B), clevis pin (M), hairpin clip (N) or
coupling screws (O).

10
Lowes.com/harborbreeze
Hardware Used
Wire Connector x 1
AA
Hardware Used
Wire Connector x 2
AA
WIRING INSTRUCTIONS
WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse
box before hanging.
WARNING: If house wires are different colors than referred to in the following steps, stop
immediately. A professional electrician is recommended to determine proper wiring.
WARNING: If you feel that you do not have enough electrical wiring knowledge or experience,
have your fan installed by a licensed electrician.
WARNING: If you are not sure if the outlet box is grounded, contact a licensed electrician for
advice, as it must be grounded for safe operation.
1. Connect the GREEN wires from the hanger ball of
downrod assembly (B) and mounting bracket (A) to the
supply ground (GREEN or bare color). Securely connect
wires using wire connector (AA) supplied.
2. Securely connect the fan WHITE wire to the supply
WHITE wire using wire connector supplied. Securely
connect the fan BLACK and BLUE wires to the supply
BLACK wire using wire connector supplied.
Note: Flushmount installation will not use the Green wire
from the downrod assembly (B).
2
Black
Fan Wire
Blue
Fan Wire
BLACK
GREEN
WHITE
White
Fan Wire
A
B
1
Supply
Ground Wire
Green Wire from
Mounting Bracket
Green Wire from
Hanger Ball

WIRING INSTRUCTIONS
11
Lowes.com/harborbreeze
FINAL INSTRUCITONS
3. Wrap electrical tape (not included) around each wire
connector and make sure no bare wire or wire strands
are visible after making connections.
Then, turn wires upward and carefully push them into
the outlet box; make sure the WHITE and GREEN
connections are on one side and the BLACK connections
are on the other side.
1. Loosen (but do not remove) the two mounting bracket
screws (L) preassembled on mounting bracket (A) that
align with the slotted holes on canopy (C). Remove the
other two mounting bracket screws (L).
Lift canopy (C) up so slotted holes engage loosened
screw heads on mounting bracket (A), then twist canopy
(C) clockwise. Re-install previously removed mounting
bracket screws (L), then tighten all screws securely.
Note: If the canopy cover (D) is loosen during installation,
please press it to the inner edge of the canopy (C).
2
H
G
BB
2. Position one blade iron (G) under blade (H). Insert three
blade screws (BB) through blade (H) and into blade iron
(G). Tighten each blade screw (BB) evenly, starting with
the center screw. Repeat for the remaining blade
assemblies.
Note: Flushmount installation will not use the downrod assembly (B) or canopy cover (D).
Hardware Used
Blade Screw x 15
BB
3
BLACK
BLUE
WHITE
GREEN
Outlet Box
AA
1
A
C
L
C
D

FINAL INSTRUCITONS
3. Loosen (do not remove) the motor screws (S) from
motor housing (F) and discard the preassembled
motor blocks. Slide the blade assemblies onto motor
housing (F) and tighten the motor screws (S) securely.
Note: If you misplace one or two motor screws during
installation of the blade assemblies, use the extra motor
screws (CC) instead.
Note: Make sure to keep loose hardware separate to
avoid confusion during installation.
3
S
G
F
12
Lowes.com/harborbreeze
Motor Screw
5. Insert the wires from the motor housing (F) through the
middle hole in the switch housing (I). Attach the switch
housing (I) to the mounting plate on motor housing (F)
by placing the keyslot holes from the switch housing (I)
onto the two protruding mounting screw (Q) heads.
Adjust the switch housing (I) until the screw heads are
aligned with the keyholes, then re-insert mounting screw
(Q) previously removed (step 4, page 12). Tighten all
mounting screws (Q) securely.
4. Remove one of the mounting screws (Q) on mounting
plate of motor housing (F), then loosen the other two.
Q
4
Mounting
Plate
Q
I
Mounting
Plate
5

FINAL INSTALLATION INSTRUCTIONS
6. Remove three switch housing screws (R) preinstalled
on the switch housing (I) and save them for later use.
Note: Make sure to keep loose hardware separate to
avoid confusion during installation.
Note: To install the fan with the light kit, proceed to
installation instruction with optional light kit.
13
Lowes.com/harborbreeze
8. Assemble fob (DD) the fan pull chain. 8
Hardware Used
Fob x 1
DD
DD
R
I
6
7. Attach the connector from the switch cover (J) to the
connector from the motor housing (F). Position the
switch cover (J) onto the switch housing (I) and secure
them with the previouly removed switch housing screws
(R).
7
I
F
J
R

14
Lowes.com/harborbreeze
2. When the season changes, you may want to change
the direction in which the fan rotates. To switch between
clockwise and counterclockwise rotation, flip the fan
reversal switch.
In warmer weather, counterclockwise rotation creates a
downward air flow, which cools the air. Push the reverse
switch on switch cover (J) to LEFT and see a SUN icon.
In cooler weather, clockwise rotation creates a upward
air flow, which moves hot air from the ceiling into the
room. Push the switch on switch cover (J) to RIGHT and
see a SNOWFLAKE icon.
2
. At least twice each year, tighten all screws and lower canopy to check mounting plate screws.
. Clean fan housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean
blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to wood
blades for added protection.
CARE AND MAINTENANCE
Important: Shut off main power supply before beginning any maintenance. Do not use water or a
damp cloth to clean the ceiling fan.
OPERATING INSTRUCTIONS
1. The fob (DD) is for fan speed control: High, Medium,
Low and Off. Pull once for each position.
1
Hardware Used
Fob x 1
DD
DD
J

1. Set screws are loose. 1. Tighten all set screws.
2. Using non-approved speed
control.
2. Some fan motors are sensitive to signals from solid-
state varible speed controls. DO NOT USE a solid-state
variable speed control.
3. Normal noise. 3. Allow "break-in" period of 24 hours. Most noises
associated with a new fan will disappear after this
period.
4. Wire connectors inside switch
housing rattling.
4. Check to make sure wire connectors in switch
housing are not rattling against each other or against
the interior wall of the switch housing.
5. Cracked blade. 5. Replace blades.
6. The distance from canopy to
ceiling is too great.
6. Make sure upper canopy is a short distance from
ceiling. It should not touch the ceiling.
7. Faulty light bulb installation. 7. Make sure light bulb is tight in socket and does not
touch on glass shade.
8. Glass is not secure. 8. Secure the glass.
1. Hanger bracket and/or ceiling
outlet box is not securely fastened.
1. Tighten the hanger bracket screws to the outlet box,
and/or secure outlet box.
2. Set screw in downrod assembly is
loose.
2. Tighten the set screw in the downrod assembly.
3. Fan hanger ball is not properly
seated in canopy tabs.
3. Turn power off, support the fan very carefully, and
check that the hanger ball is properly seated.
4. Set screw in motor coupling is
loose.
4. Raise motor coupling up and tighten set screws
securely.
5. Blade is loose. 5. Check that all blades are screwed firmly into blade
holders.
6. Blade holders are loose. 6. Check to be sure the fan blade irons seat firmly and
uniformly on the surface of the motor. If flanges are
seated incorrectly, loosen the flange screws and
retighten.
7. Blade out of balance. 7. Interchange two adjacent blades; this will redistribute
the weight and possibly result in smoother operation. Or,
refer to the instructions inside the balance kit (P).
8. Fan too close to vaulted ceiling. 8. Lower or move fan. Extension downrods may be
ordered.
9. Transition to different speed. 9. When switching from medium to low speed, you may
notice some fan wobble in the fan. When the fan
stabilizes at low speed, wobble should disappear.
10. Fan not securely mounted. 10. Make sure canopy and mounting bracket are
tightened securely to ceiling joist.
Fan sounds noisy
Fan wobbles
15
Lowes.com/harborbreeze
TROUBLESHOOTING
PROBLEM PROBABLE CAUSE CORRECTIVE ACTION

16
Lowes.com/harborbreeze
TROUBLESHOOTING
1. Power turned off, fuse blown or
circuit breaker tripped.
1. Turn power on, replace fuse or reset breaker.
2a. Turn power off and loosen canopy; check all
connections according to section WIRING
INSTRUCTIONS on page 10.
2b. Check the plug connection in the switch housing.
3. Motor reversing switch not
engaged.
3. Push switch firmly right or left. Fan will not operate
when switch is in the middle.
4. Pull chain switch not "on". 4. Pull switch chain.
1. Wrong wire connection. 1a. Refer to Step 1, page 10 to ensure all wire
connections were done correctly.
2. Bulb is burned out. 2b. Replace the bulbs.
Light does not work
Fan does not start
2. Loose wire connections or wrong
connections.
PROBLEM PROBABLE CAUSE CORRECTIVE ACTION

17
Lowes.com/harborbreeze
LIMITED LIFETIME WARRANTY
The manufacturer warrants this fan to be free from defects in workmanship and material present at
time of shipment from the factory for life (with limitations) from the date of purchase. This warranty
applies only to the original purchaser. The manufacturer agrees to correct such defect at no charge
or, at our option, replace the ceiling fan with a comparable or superior model.
To obtain warranty service, present a copy of your sales receipt as proof of purchase. All cost of
removal and reinstallation are the expressed responsibility of the purchaser. Any damage to the ceiling
fan by accident, misuse or improper installation, or by affixing accessories not produced by this warranty,
are at the purchaser’s own responsibility. The manufacturer assumes no responsibility whatsoever for
fan installation during the limited lifetime warranty. Any service performed by an unauthorized person
will render the warranty invalid.
Due to varying climatic conditions, this warranty does not cover changes in brass finish, rusting, pitting,
tarnishing, corroding or peeling. Brass finish fans maintain their beauty when protected from varying
weather conditions.
NOTE: A small amount of “ wobble ” is normal and should not be considered a defect.
Any replacement of defective parts for the ceiling fan must be reported within the first year from the date
of purchase. For the balance of the warranty, call our customer service department at 1-800-643-0067
for return authorization and shipping instructions so that we may repair or replace the ceiling fan. Any
fan or parts returned improperly packaged is the sole responsibility of the purchaser. There is no further
expressed warranty. The manufacturer disclaims any and all implied warranties.
The duration of any implied warranty which can not be disclaimed is limited to the lifetime limited period
as specified in our warranty. The manufacturer shall not be liable for incidental, consequential or special
damages arising at or in connection with product use or performance except as may other wise be
accorded by law. This warranty gives you specific legal rights, and you also have other rights which vary
from state to state. This warranty supersedes all prior warranties.

REPLACEMENT PARTS LIST
18
Lowes.com/harborbreeze
For replacement parts, call our customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST,
Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
AB
G
HIJ
DD
CC
BB
AA
C
D
E
Part Description Part#
A Mounting Bracket A102-0132070
B Downrod Assembly A103-0156346
C Canopy A101-0347346
D Canopy Hole Cover A108-0260346
E Coupling Cover A106-0198346
G Blade Iron A143-0199346
H Blade A141-0366030
I Switch Housing A121-0245346
J Switch Cover A124-0266346
AA Wire Connector
BB Blade Screw
CC Extra Motor Screw
DD Fob
B168-0385070
Printed in China
Harbor Breeze® is a registered trademark of LF, LLC. All Rights Reserved.