Harbor Freight Tools 96138 Parts list manual

FOLDING WORK BENCH
Model 96138
ASSEMBLY AND OPERATION INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
Copyright©2007 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.

Page 2SKU 96138 For technical questions, please call 1-800-444-3353.
SPECIFICATIONS
Material Formed sheet metal with black
enamel coating
Overall Dimensions 47-1/2” L x 26-1/4” D x 23-5/8” H
Work Table Size 47-3/8” L x 23-3/4” D x 5/8” Thick
Maximum Weight Capacity 220 lb.
Peg Board 47” L x 23-5/8” D x 5/8” Thick
Weight 57.6 Lbs.
Also includes Ruler on Work Table
Save This Manual
You will need this manual for the safety warnings and precautions, assembly, oper-
ating, inspection, maintenance and cleaning procedures, parts list and assembly diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the front
cover. Write the product’s serial number in the back of the manual near the assembly dia-
gram, or write month and year of purchase if product has no number. Keep this manual
and invoice in a safe and dry place for future reference.
GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in
serious injury.
SAVE THESE INSTRUCTIONS
Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
Keep bystanders, children, and visitors away while assembling theWork Bench.
Distractions can cause you to lose control. Never allow children to climb on or play
on the Workbench. Never allow children to climb or play on the Workbench.
Stay alert. Watch what you are doing, and use common sense during assembly
and installation. Do not use, assemble or install the Work Bench while tired or
under the influence of drugs, alcohol, or medication. A moment of inattention
during set-up and assembly may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control in unexpected situations.
1.
2.
3.
4.
5.

Page 3SKU 96138 For technical questions, please call 1-800-444-3353.
Use safety equipment. Always wear ANSI-approved eye protection during
assembly and installation. Nonskid safety shoes, and hard hat, must be used for
appropriate conditions.
Do not force the product. Use the correct product for your application. The
correct product will do the job better and safer at the rate for which it is designed.
Do not force the product and do not use the product for a purpose for which it is
not intended.
When servicing this product, use only identical replacement parts.
Maintain labels and nameplates on the product. These carry important informa-
tion. If unreadable or missing, contact Harbor Freight Tools for a replacement.
Maintain a safe working environment. Make sure there is adequate surrounding
workspace.
Do not exceed the maximum weight capacity of 220 lb.
Two adults should install the Work Bench. This will assure proper set-up of the
unit.
This product must be installed into wall studs that can support the maximum
weight of the item and the weight of all items being stored on the Work Bench.
Failure to do so may cause the Work Bench and its contents to loosen or fall, caus-
ing serious damage and injury.
When drilling holes for installation, always check to make sure that no electri-
cal wires or cables are in the drilling path.
Install theWork Bench on a flat, level surface capable of supporting the weight
of the Work Bench and the weight of all items placed on the Work Bench.
UNPACKING
When unpacking, check to make sure that the item is intact and undamaged. If any
parts are missing or broken, please call Harbor Freight Tools at the number shown on the
cover of this manual as soon as possible.
ASSEMBLY INSTRUCTIONS
Note: For additional information regarding the parts listed in the following pages, refer to
the Assembly Diagrams near the end of this manual.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.

Page 4SKU 96138 For technical questions, please call 1-800-444-3353.
Hook Bar (13)
Peg Board
Support (7/8)
Peg Board (B)
Figure 1
Anchor Bolt (H)
Connect Rear Legs (5/6) to Peg Board Support (7) with two Nuts, Bolts and Wash-
ers (A) through each Leg (5/6) and Peg Board Support (7).
Connect Hook Bar (13) to each Peg Board Support (7) with Nut, Bolt and Washer
(A)-see Figure 1 and Assembly Diagram.
Secure Peg Board (C) to each Peg Support (7/8) with two Screws (B). Screws are
to be threaded through each of the lower holes in the Peg Board (8). Insert Screws
from the back with bolts and washers at the front of the Work Bench.
Secure the assembled section (Steps 1-4) to wall studs. Use the 3 holes on each
Leg and Peg Support as a guide and mark the holes onto the desired wall location.
Note that the holes for securing the Work Bench to the wall are marked by a small
plate at each hole-see Figure 1.
Set the back section of the Work Bench against the wall as desired, making certain
that the holes line up with the markings on the wall.
Pre-drill holes (drill not included), making certain that the drilling path is free of any
wires, lines and cables.
Secure the Work Bench to the wall with Anchor Bolts (H). Once the Anchor Bolts (H)
are secured to the wall, make certain that the Legs are firmly resting on the floor.
Attach Rear Table Support (2) to both rear Legs (5) using Nuts, Bolts and Washers
(A).
1.
2.
3.
4.
5.
6.
7.
8.

Page 5SKU 96138 For technical questions, please call 1-800-444-3353.
Bottom
Shelf (12)
Bottom
Shelf (12)
Bolt, Washer,
Nut (A)
Leg (5)
Figure 2
Cross Brace (10)
Attach each Bottom Shelf (12) to Left Cross Brace (9) and Right Cross Brace (10)
using Bolts, Washers and Nuts (A)-see Figure 2.
Secure each Cross Brace (9/10) with Bottom Shelf (12) to each Leg (11) using Nut,
Bolt and Washer (D).
Connect Top Brace (3/4) to each Leg (5) with Nut (D).
Attach Front Table Support (1) to front Legs (11) Nuts, Bolts and Washers (E).
Set Table (14) onto both Top Braces (3/4), Rear Table Support (2) and Front Table
Support (1).
Using the pre-drilled holes in the Table, attach the Table to the Rear Table Support
(2) and Front Table Support (1) using three Screws (G) up through each.
When you have finished assembling the Folding Work Bench, make certain that all
Legs rest securely on the floor. Make certain all hardware is tight and secure. Fold
up the Work Bench and use the locking latch to make certain it is securely collapsed
in the upright position.
INSPECTION, MAINTENANCE, AND CLEANING
BEFORE EACH USE, inspect the general condition of the Folding Work Bench.
Check for loose screws, misalignment or binding of moving parts, cracked or bro-
ken parts, and any other condition that may affect its safe operation. Do not use
damaged equipment.
9.
10.
11.
12.
13.
14.
15.
1.

Page 6SKU 96138 For technical questions, please call 1-800-444-3353.
Clean the Folding Work Bench with a soft cloth. Do not use water, flammable de-
tergents or harsh abrasives as they will damage the Work Bench. Avoid getting
the table wet.
PARTS LIST
Main Parts
Part Description Q’ty
1 Front Table Support 1
2 Rear Table Support 1
3 Left Top Brace 1
4 Right Top Brace 1
5 Left Rear Leg 4
6 Right Rear Leg 2
7 Left Peg Board Support 1
Part Description Q’ty
8 Right Peg Board Support 1
9 Left Cross Brace 1
10 Right Cross Brace 1
11 Leg 2
12 Bottom Shelf 2
13 Hook Bar 1
14 Table 1
Hardware
Part Description Q’ty
A Nut, Bolt, Washer M6x12 22 sets
B Nut, Bolt, Washer 6x16 2 sets
C Peg Board 1
D Nut,Bolt, Washer M8x20 4 sets
E Nut, Bolt, Washer M8x40 4 sets
Part Description Q’ty
F Hook 30
G Large Hook 1
H Screw ST 6 x 38 6
I Anchor Bolts 6
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEM-
BLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR
SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS
TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR
HER INSTALLATION OF REPLACEMENT PARTS THERETO.
2.

Page 7SKU 96138 For technical questions, please call 1-800-444-3353.
ASSEMBLY AND PARTS DIAGRAM
14
C
8
D
D
E