Harman JBL CINEMA SB120 User manual

JBL CINEMA SB120
OWNER’S MANUAL

22
IMPORTANT SAFETY INSTRUCTIONS
Verify Line Voltage Before Use
The JBL CINEMA BAR 120 (soundbar) has been designed for
use with 100-240 volt, 50/60 Hz AC current. Connection to a
line voltage other than that for which your product is intended
can create a safety and re hazard and may damage the unit. If
you have any questions about the voltage requirements for your
specic model or about the line voltage in your area, contact your
retailer or customer service representative before plugging the unit
into a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord supplied with
your unit. We do not recommend that extension cords be used with
this product. As with all electrical devices, do not run power cords
under rugs or carpets, or place heavy objects on them. Damaged
power cords should be replaced immediately by an authorized
service center with a cord that meets factory specications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always
pull the plug; never pull the cord. If you do not intend to use this
speaker for any considerable length of time, disconnect the plug
from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside this product.
Opening the cabinet may present a shock hazard, and any
modication to the product will void your warranty. If water
accidentally falls inside the unit, disconnect it from the AC power
source immediately, and consult an authorized service center.

www.jbl.com
English
33
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS 2
1 INTRODUCTION 4
2 WHAT’S IN THE BOX 4
3 PRODUCT OVERVIEW 5
3.1 CONTROLS AND INDICATORS 5
3.2 CONNECTORS 5
3.3 REMOTE CONTROL 6
4 PLACE 7
4.1 DESKTOP PLACEMENT 7
4.2 WALL-MOUNTING 7
5 CONNECT 8
5.1 TV CONNECTION 8
5.2 BLUETOOTH CONNECTION 8
6 PLAY 9
6.1 POWER-ON/AUTO STANDBY/AUTO WAKEUP 9
6.2 PLAY FROM THE TV SOURCE 10
6.3 PLAY FROM THE BLUETOOTH SOURCE 10
7 SOUND SETTINGS 11
7.1 PRE-DEFINED EQ SETTINGS 11
7.2 VOICE MODE 11
8 RESTORE FACTORY SETTINGS 12
9 SOFTWARE UPDATE 12
10 PRODUCT SPECIFICATIONS 13
11 TROUBLESHOOTING 13
12 TRADEMARKS 14
13 OPEN SOURCE LICENSE NOTICE 15

44
1 INTRODUCTION
Thank you for purchasing the JBL CINEMA BAR 120 (soundbar)
which is designed to bring an extraordinary sound experience to
your home entertainment system. We encourage you to take a
few minutes to read through this manual, which describes the
product and includes step-by-step instructions for setting up and
getting started.
To make the most of product features and support, you
may need to update the product software through the USB
connector in the future. Refer to the software update section
in this manual to ensure that your product has the latest
software.
Designs and specications are subject to change without notice.
If you have any questions about the soundbar, installation or
operation, please contact your retailer or customer service
representative, or visit our website: www.jbl.com.
2 WHAT’S IN THE BOX
Unpack the box carefully and ensure that the following parts are
included. If any part is damaged or missing, do not use it and
contact your retailer or customer service representative.
Main unit
Remote control (with 2 AAA batteries)
(AAA)
Power cord*
* Power cord quantity and plug type vary by region.
HDMI cable
Wall-mounting kit

www.jbl.com
English
55
Product information & wall-mounting template 3 PRODUCT OVERVIEW
3.1 Controls and indicators
1 2 3 4
1. (Power)
• Switch on or to standby
2. -/+ (Volume)
• Decrease or increase the volume
• Press and hold to decrease or increase the volume
continuously
• Press the two buttons together to mute or unmute.
3. (Source)
• Select a sound source: Bluetooth (default) or HDMI
ARC (TV connected through the connector),
or Optical (TV / digital device connected through the
connector)
4. Status indicators
Solid red Entering standby mode
Solid white HDMI ARC source selected
Solid amber Optical source selected
Solid blue Connected to Bluetooth
Fast flashing blue Entering Bluetooth pairing mode
Flashing blue Volume change ongoing
Slow flashing blue Maximum volume level reached
Sound muted
3.2 Connectors
C~
C~
ERVICEONLY
1 2 3 4
1.
• Connect to power
2.
• USB connector for software update
• Connect to a USB storage device for audio play (for the
US version only)
3.
• Connect to the HDMI ARC input on your TV