Hatco Glo-Ray GRSDH-24 User manual

GLO-RAY®
Merchandising Display Warmer
GRSDH, GRSDS & GRSDS/H Series
Installation &
Operating Manual
I&W #07.05.011.00
This manual contains important safety information
concerning the maintenance, use and operation
of this product. Failure to follow the instructions
contained in this manual may result in serious
injury. If you’re unable to understand the contents
of this manual, please bring it to the attention
of your supervisor. Do not operate this equipment unless
you have read and understood the contents
of this manual.
Este manual contiene importante información sobre
seguridad concerniente al mantenimiento, uso
y operación de este producto. Cualquier falla
en el seguimiento de las instrucciones contenidas
en este manual puede resultar en un serio daño.
Si usted no puede entender el contenido de este
manual por favor pregunte a su supervisor.
No opere este equipo al menos que haya leído
y comprendido el contenido de este manual.

Business 8:00 a.m. to 5:00 p.m.
Hours: Central Standard Time
(Summer Hours: June to September -
8:00 a.m. to 5:00 p.m. C.S.T.
Monday through Thursday
8:00 a.m. to 2:30 p.m. C.S.T. Friday)
Telephone: [phone]
Fax: [phone] (Parts & Service)
[phone] (International)
24-Hour 7-Day Parts & Service
Assistance available in the
United States and Canada by
calling [phone].
Additional information can be found by visiting our
web site at www.hatcocorp.com
Form No. GRSDM-1207 i
INTRODUCTION
The Hatco Glo-Ray Merchandising Display
Warmers, GRSDH (Horizontal Shelf), GRSDS
(Slant Shelf), and GRSDS/H (one slant shelf and
one horizontal shelf) are perfect for holding wrapped
sandwiches or boxed pizza on a buffet line or at
temporary serving areas. These warmers hold hot
wrapped products and keep them at optimum
serving temperatures without affecting quality.
Prefocused infrared heat from above and a
thermostatically controlled heated base extends the
holding times of most wrapped food. The infrared
heating elements are guaranteed against burnout
and breakage for two years. These units also
feature incandescent lights along with a cord and
plug set(s).
This manual provides the installation, safety
and operating instructions for the Glo-Ray
Merchandising Display Warmers. We recommend
all installation, operating and safety instructions
appearing in this manual be read prior to installation
or operation of your Hatco Merchandising Display
Warmer. Safety instructions that appear in this
manual after a warning symbol and the words
WARNING or CAUTION printed in bold face are
very important. WARNING means there is the
possibility of serious personal injury or death to
yourself or others. CAUTION means there is the
possibility of minor or moderate injury. The word
NOTICE signifies the possibility of equipment or
property damage only.
Hatco Glo-Ray Merchandising Display Warmers
are a product of extensive research and field testing.
The materials used were selected for maximum
durability, attractive appearance and optimum
performance. Every unit is thoroughly inspected
and tested prior to shipment.
CONTENTS
Important Owner Information...............................i
Introduction ...........................................................i
Important Safety Instructions .............................1
Model Designation ...............................................2
Model Description................................................2
All Models........................................................2
GRSDH Models...............................................2
GRSDS Models...............................................2
GRSDS/H Models ...........................................2
Specifications.......................................................3
Plug Configurations.........................................3
Electrical Rating Charts...................................3
Dimensions GRSDH Models...........................8
Dimensions GRSDS Models ...........................9
Dimensions GRSDS/H Models .....................10
Installation...........................................................11
All Models ......................................................11
Location .........................................................11
Operation ............................................................12
Maintenance .......................................................13
General..........................................................13
Cleaning ........................................................13
Display Light Bulb Replacement ...................13
Accessories ........................................................14
Troubleshooting .................................................15
Hatco Limited Warranty.....................................16
Authorized Parts Distributors ............Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number
(identification decal located on the back of the unit),
voltage and purchase date of your Glo-Ray®
Merchandising Display Warmer in the spaces below.
Please have this information available when calling
Hatco for service assistance.
Model No. ________________________________
Serial No. ________________________________
Voltage __________________________________
Date of Purchase __________________________

Form No. GRSDM-1207
1
IMPORTANT SAFETY INFORMATION
WARNINGS
To avoid any injury, turn the power switch
OFF, unplug the unit from the power source
and allow to cool before performing any
cleaning or maintenance.
Plug unit into a properly grounded electrical
outlet of the correct voltage, size and plug
configuration. If the plug and receptacle do
not match, contact a qualified electrician to
determine the proper voltage and size and
install the proper electrical outlet.
Unit is not waterproof. To avoid electrical
shock or personal injury DO NOT submerge
in water. Do not operate if it has been
submerged in water.
To avoid electrical shock or personal injury,
do not steam clean or use excessive water on
the unit.
For safe and proper operation, the unit must
be located a reasonable distance from
combustible walls and materials. If safe
distances are not maintained, discoloration or
combustion could occur.
Do not lay unit on the side with the control
panel or damage to unit could occur.
To prevent any injury or damage to the unit
do not pull unit by power cord.
To prevent any injury, discontinue use if
power cord is frayed or worn.
For safe and proper operation do not place
food product directly onto hardcoat surface.
Food product must be wrapped, boxed
or on a food pan.
Only light bulbs which meet or exceed N.S.F.
standards, specifically designed for food
holding areas must be used. Breakage of light
bulbs not specially coated could result in
personal injury and/or food contamination.
If service is required on this unit, contact your
Authorized Hatco Service Agent, or contact
the Hatco Service Department at 800-558-
0607 or 414-671-6350; fax [phone]
or International fax [phone].
This product has no “user” serviceable parts.
To avoid damage to the unit or injury
to personnel, use only Authorized Hatco
Service Agents and Genuine Hatco
Replacement Parts when service is required.
WARNINGS
Genuine Hatco Replacement Parts are
specified to operate safely in the
environments in which they are used. Some
aftermarket or generic replacement parts do
not have the characteristics that will allow
them to operate safely in Hatco equipment. It
is essential to use Hatco Replacement Parts
when repairing Hatco equipment. Failure to
use Hatco Replacement Parts may subject
operators of the equipment to hazardous
electrical voltage, resulting in electrical shock
or burn.
CAUTIONS
Some exterior surfaces on the unit will get
hot. Use caution when touching these areas
to avoid injury.
To avoid any injury or damage locate the unit
at the proper counter height, in an area that
is convenient for use. The location should
be level to prevent the unit or its contents
from accidentally falling, and strong enough
to support the weight of the unit and food
displayed.
The National Sanitation Foundation (NSF)
requires units over 36" (914 mm) in length
or weighing more than 80 lbs. (36 kg) to be
either sealed or raised on the installation
surface. If this unit cannot be sealed at the
point of use, 4" (102 mm) legs are included to
allow for proper cleaning access below unit.
Unit is not weatherproof. For safe and proper
operation locate the unit indoors where
the ambient air temperature is constant
and is a minimum of 70°F (21°C).
NOTICES
Use only non-abrasive cleaners. Abrasive
cleaners could scratch the finish marring
its appearance and making it susceptible
to dirt accumulation.
Only soft cleaning cloths with mild soap
and water should be used to clean breath
protector(s). Breath protector(s) are made
of shatterproof polycarbonate and will
scratch or crack if proper care is not taken.
IMPORTANT! Read the following important safety information to avoid personal injury or
death, and to avoid damage to the equipment or property.

Form No. GRSDM-1207 2
ALL MODELS
All models are constructed of aluminum and
stainless steel. Features include tempered glass
side panels, a temperature controlled heated base,
infrared upper heating elements, incandescent
lights, product divider rods, legs and a cord and plug
set.
GRSDH MODELS
The GRSDH models are horizontal shelf warmers
designed to hold hot wrapped product.
These models can be ordered in various widths, 24"
to 60" (610 to 1524 mm), and are available in single
or dual shelf models.
GRSDS MODELS
The GRSDS models are slant shelf warmers
designed to hold hot wrapped product. The shelves
are slanted for the convenience of self-serve.
These models can be ordered in various widths, 24"
to 60" (610 to 1524 mm), and are available in single
or dual shelf models.
24" and 36" units available in triple shelf models.
GRSDS/H MODELS
The GRSDS/H models are dual shelf units that
include one slanted shelf and one horizontal shelf.
These models can be ordered in widths of 30"
(762 mm), 36" (914 mm), or 41" (1041 mm).
Ideal for holding popcorn on the top horizontal
shelf and nachos, box pizza or wrapped product
on the bottom slanted shelf.
MODEL DESCRIPTION
Figure 2. Glo-Ray Model GRSDH - Single Shelf
Figure 3. Glo-Ray Model GRSDS - Dual Shelf
Figure 4. Glo-Ray Model GRSDS/H - Dual Shelf
MODEL DESIGNATION
GR S D H - 24 D HW
Glo-Ray
Sandwich
Display
D = Dual Shelf
T = Triple Shelf
Width of Unit (inches)
High Watt
H = Horizontal Shelf
S = Slant Shelf Only
S/H = One Slanted and
One Horizontal Shelf
Figure 1. Model Designation

Form No. GRSDM-12073
SPECIFICATIONS
ELECTRICAL RATING CHART – GRSDH MODELS - HORIZONTAL SINGLE SHELF
* NEMA 5-20P for Canada
Shaded area pertains to Export Models only
PLUG CONFIGURATIONS
Units are supplied from the factory with an electrical
cord and plug. (Figure 5.)
WARNING
Plug unit into a properly grounded electrical
outlet of the correct voltage, size and plug
configuration. If the plug and receptacle do not
match, contact a qualified electrician to
determine the proper voltage and size and install
the proper electrical outlet.
NEMA 5-15P
CEE 7/7 Schuko BS 1363
Figure 5. Plug Configurations
NEMA 5-20P NEMA L14-20P
* Receptacle not supplied by Hatco
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSDH-24 120 830 6.9 NEMA 5-15P 51 lbs. (23 kg)
GRSDH-30 120 970 8.1 NEMA 5-15P 58 lbs. (26 kg)
200E 940 4.7 CEE 7/7 Schuko 58 lbs. (26 kg)
220E 890 4.0 CEE 7/7 Schuko 58 lbs. (26 kg)
240E 1060 4.4 BS-1363 58 lbs. (26 kg)
220-230 (CE) 890-974 4.0-4.2 CEE 7/7 Schuko 58 lbs. (26 kg)
230-240 (CE) 974-1060 4.2-4.4 BS-1363 58 lbs. (26 kg)
GRSDH-36 120 1170 9.8 NEMA 5-15P 66 lbs. (30 kg)
220E 1074 4.9 CEE 7/7 Schuko 66 lbs. (30 kg)
240E 1278 5.3 BS-1363 66 lbs. (30 kg)
220-230 (CE) 1074-1174 4.9-5.1 CEE 7/7 Schuko 66 lbs. (30 kg)
230-240 (CE) 1174-1278 5.1-5.3 BS-1363 66 lbs. (30 kg)
GRSDH-41 120 1340 11.2 NEMA 5-15P 74 lbs. (34 kg)
200E 1180 5.9 No Plug 74 lbs. (34 kg)
220E 1228 5.6 CEE 7/7 Schuko 74 lbs. (34 kg)
240E 1464 6.1 BS-1363 74 lbs. (34 kg)
220-230 (CE) 1228-1343 5.6-5.8 CEE 7/7 Schuko 74 lbs. (34 kg)
230-240 (CE) 1343-1464 5.8-6.1 BS-1363 74 lbs. (34 kg)
GRSDH-52 120 1760 14.7 NEMA 5-15* 86 lbs. (39 kg)
220E 1604 7.3 CEE 7/7 Schuko 86 lbs. (39 kg)
240E 1912 8.0 BS-1363 86 lbs. (39 kg)
220-230 (CE) 1604-1754 7.3-7.6 CEE 7/7 Schuko 86 lbs. (39 kg)
230-240 (CE) 1754-1912 7.6-8.0 BS-1363 86 lbs. (39 kg)
GRSDH-60 120/208-240 2100 15.0 NEMA L14-20P 198 lbs. (90 kg)
220E 1830 8.3 CEE 7/7 Schuko 198 lbs. (90 kg)
240E 2180 9.1 BS-1363 198 lbs. (90 kg)
220-230 (CE) 1830-2001 8.3-8.7 CEE 7/7 Schuko 198 lbs. (90 kg)
230-240 (CE) 2001-2180 8.7-9.1 BS-1363 198 lbs. (90 kg)
***
**
NEMA 14-30P
*

Form No. GRSDM-1207 4
ELECTRICAL RATING CHART – GRSDH MODELS - HORIZONTAL DUAL SHELF
SPECIFICATIONS
†Not available in Canada
Shaded area pertains to Export Models only
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSDH-24D 120 1660 13.8 NEMA 5-15P 90 lbs. (41 kg)
GRSDH-30D 120 1920 16.0 NEMA 5-20P 100 lbs. (45 kg)
220E 1780 8.1 CEE 7/7 Schuko 100 lbs. (45 kg)
240E 2120 8.8 BS-1363 100 lbs. (45 kg)
220-230 (CE) 1780-1948 8.1-8.5 CEE 7/7 Schuko 100 lbs. (45 kg)
230-240 (CE) 1948-2120 8.5-8.8 BS-1363 100 lbs. (45 kg)
GRSDH-36D 120/208-240 2340 9.8 NEMA L14-20P 112 lbs. (51 kg)
220E 2148 9.8 CEE 7/7 Schuko 112 lbs. (51 kg)
240E 2556 10.7 BS-1363 112 lbs. (51 kg)
220-230 (CE) 2148-2348 9.8-10.2 CEE 7/7 Schuko 112 lbs. (51 kg)
230-240 (CE) 2348-2556 10.2-10.7 BS-1363 112 lbs. (51 kg)
GRSDH-41D 120†1340/1340‡11.2/11.2‡(2) NEMA 5-15P‡126 lbs. (57 kg)
120/208-240 2680 11.2 NEMA L14-20P 126 lbs. (57 kg)
220E 2456 11.2 CEE 7/7 Schuko 126 lbs. (57 kg)
240E 2928 12.2 BS-1363 126 lbs. (57 kg)
220-230 (CE) 2456-2686 11.2-11.7 CEE 7/7 Schuko 126 lbs. (57 kg)
230-240 (CE) 2686-2928 11.7-12.2 BS-1363 126 lbs. (57 kg)
GRSDH-52D 120†1760/1760‡14.7/14.7‡(2) NEMA 5-15P‡150 lbs. (68 kg)
120/208-240 3520 14.7 NEMA L14-20P 150 lbs. (68 kg)
220E 3208 14.6 CEE 7/7 Schuko 150 lbs. (68 kg)
240E 3824 15.9 BS-1363 150 lbs. (68 kg)
220-230 (CE) 3208-3508 14.6-15.3 CEE 7/7 Schuko 150 lbs. (68 kg)
230-240 (CE) 3508-3824 15.3-15.9 BS-1363 150 lbs. (68 kg)
GRSDH-60D 120/208-240†4200 17.5 NEMA L14-20P 268 lbs. (122 kg)
220E 3660 16.6 No Plug 268 lbs. (122 kg)
240E 4360 18.2 No Plug 268 lbs. (122 kg)
220-230 (CE) 3660-4002 16.6-17.4 No Plug 268 lbs. (122 kg)
230-240 (CE) 4002-4360 17.4-18.2 No Plug 268 lbs. (122 kg)
‡Unit comes equipped with two cord and plug sets, requiring two separate 15 amp power circuits.

Form No. GRSDM-12075
SPECIFICATIONS
ELECTRICAL RATING CHART – GRSDS MODELS - SLANT SINGLE SHELF
Shaded area pertains to Export Models only
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSDS-24 120 695 5.8 NEMA 5-15P 72 lbs. (33 kg)
220E 629 2.9 CEE 7/7 Schuko 72 lbs. (33 kg)
240E 749 3.1 BS-1363 72 lbs. (33 kg)
220-230 (CE) 629-688 2.9-3.0 CEE 7/7 Schuko 72 lbs. (33 kg)
230-240 (CE) 688-749 3.0-3.1 BS-1363 72 lbs. (33 kg)
GRSDS-24HW 120 1165 9.7 NEMA 5-15P 72 lbs. (33 kg)
GRSDS-30 120 790 6.6 NEMA 5-15 80 lbs. (36 kg)
220E 730 3.3 CEE 7/7 Schuko 80 lbs. (36 kg)
240E 862 3.6 BS-1363 80 lbs. (36 kg)
220-230 (CE) 730-799 3.3-3.5 CEE 7/7 Schuko 80 lbs. (36 kg)
230-240 (CE) 799-870 3.5-3.6 BS-1363 80 lbs. (36 kg)
GRSDS-30HW 120 1450 12.1 NEMA 5-15P* 80 lbs. (36 kg)
GRSDS-36 120 935 7.8 NEMA 5-15P 92 lbs. (42 kg)
220E 864 3.9 CEE 7/7 Schuko 92 lbs. (42 kg)
240E 1030 4.3 BS-1363 92 lbs. (42 kg)
220-230 (CE) 865-946 3.9-4.1 CEE 7/7 Schuko 92 lbs. (42 kg)
230-240 (CE) 946-1030 4.1-4.3 BS-1363 92 lbs. (42 kg)
GRSDS-36HW 120 1775 14.8 NEMA 5-15P* 92 lbs. (42 kg)
GRSDS-41 120 1090 9.1 NEMA 5-15P 96 lbs. (44 kg)
200 1062 5.3 No Plug 96 lbs. (44 kg)
220E 1003 4.6 CEE 7/7 Schuko 96 lbs. (44 kg)
240E 1195 5.0 BS-1363 96 lbs. (44 kg)
220-230 (CE) 1003-1097 4.6-4.8 CEE 7/7 Schuko 96 lbs. (44 kg)
230-240 (CE) 1097-1195 4.8-5.0 BS-1363 96 lbs. (44 kg)
GRSDS-41HW 120†2070 17.3 NEMA 5-20P 96 lbs. (44 kg)
GRSDS-52 120 1400 11.7 NEMA 5-15P 102 lbs. (46 kg)
220E 1275 5.8 CEE 7/7 Schuko 102 lbs. (46 kg)
240E 1520 6.3 BS-1363 102 lbs. (46 kg)
220-230 (CE) 1275-1396 5.8-6.1 CEE 7/7 Schuko 102 lbs. (46 kg)
230-240 (CE) 1396-15 20 6.1-6.3 BS-1363 102 lbs. (46 kg)
GRSDS-52HW 120/208-240 2710 14.8 NEMA L14-20P 102 lbs. (46 kg)
GRSDS-60 120 1715 14.3 NEMA 5-15P* 108 lbs. (49 kg)
220E 1665 7.6 CEE 7/7 Schuko 108 lbs. (49 kg)
240E 1715 7.2 BS-1363 108 lbs. (49 kg)
220-230 (CE) 1665-1820 7.6-7.9 CEE 7/7 Schuko 108 lbs. (49 kg)
230-240 (CE) 1575-1715 6.8-7.2 BS-1363 108 lbs. (49 kg)
†Not available in Canada
* NEMA 5-20P for Canada

Form No. GRSDM-1207 6
SPECIFICATIONS
ELECTRICAL RATING CHART – GRSDS MODELS - SLANT DUAL SHELF
* NEMA 5-20P for Canada
Shaded area pertains to Export Models only
‡Unit comes equipped with two cord and plug sets, requiring two separate 15 amp power circuits.
Unit comes equipped with two cord and plug sets, requiring two separate 20 amp power circuits.
♦
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSDS-24D 120 1355 11.3 NEMA 5-15P 128 lbs. (58 kg)
220E 1352 6.1 CEE 7/7 Schuko 128 lbs. (58 kg)
240E 1611 6.7 BS-1363 128 lbs. (58 kg)
220-230 (CE) 1352-1479 6.1-6.4 CEE 7/7 Schuko 128 lbs. (58 kg)
230-240 (CE) 1479-1611 6.4-6.7 BS-1363 128 lbs. (58 kg)
GRSDS-24DHW 120/208-240 2290 9.7 NEMA L14-20P 128 lbs. (58 kg)
GRSDS-30D 120 1530 12.8 NEMA 5-15* 140 lbs. (64 kg)
220E 1419 6.5 CEE 7/7 Schuko 140 lbs. (64 kg)
240E 1690 7.0 BS-1363 140 lbs. (64 kg)
220-230 (CE) 1419-1552 6.5-6.8 CEE 7/7 Schuko 140 lbs. (64 kg)
230-240 (CE) 1552-1690 6.8-7.0 BS-1363 140 lbs. (64 kg)
GRSDS-30DHW 120†1400/1450‡11.7/12.1‡(2) NEMA 5-15P‡140 lbs. (64 kg)
120/208-240 2850 12.1 NEMA L14-20P 140 lbs. (64 kg)
GRSDS-36D 120 1810 15.1 NEMA 5-20P 158 lbs. (72 kg)
220E 1669 7.6 CEE 7/7 Schuko 158 lbs. (72 kg)
240E 1990 8.3 BS-1363 158 lbs. (72 kg)
220-230 (CE) 1670-1827 7.6-7.9 CEE 7/7 Schuko 158 lbs. (72 kg)
230-240 (CE) 1827-1990 7.9-8.3 BS-1363 158 lbs. (72 kg)
GRSDS-36DHW 120/208-240 3490 14.8 NEMA L14-20P 158 lbs. (72 kg)
GRSDS-41D 120†1090/1030‡9.1/8.6‡(2) NEMA 5-15P‡178 lbs. (81 kg)
120/208-240 2120 9.1 NEMA L14-20P 178 lbs. (81 kg)
200 2098 10.5 No Plug 178 lbs. (81 kg)
220E 1951 8.9 CEE 7/7 Schuko 178 lbs. (81 kg)
240E 2325 9.7 BS-1363 178 lbs. (81 kg)
220-230 (CE) 1951-2135 8.9-9.3 CEE 7/7 Schuko 178 lbs. (81 kg)
230-240 (CE) 2135-2325 9.3-9.7 BS-1363 178 lbs. (81 kg)
GRSDS-41DHW 120†2010/2070♦16.8/17.3♦(2) NEMA 5-20P♦178 lbs. (81 kg)
120/208-240 4080 17.3 NEMA L14-20P 178 lbs. (81 kg)
GRSDS-52D 120†1400/1325‡11.7/11.0‡(2) NEMA 5-15P‡205 lbs. (93 kg)
120/208-240 2725 11.7 NEMA L14-20P 205 lbs. (93 kg)
220E 2483 11.3 CEE 7/7 Schuko 205 lbs. (93 kg)
240E 2960 12.3 BS-1363 205 lbs. (93 kg)
220-230 (CE) 2485-2718 11.3-11.8 CEE 7/7 Schuko 205 lbs. (93 kg)
230-240 (CE) 2718-2960 11.8-12.3 BS-1363 205 lbs. (93 kg)
GRSDS-52DHW 120/208-240 5340 22.6 NEMA 14-30P 205 lbs. (93 kg)
GRSDS-60D 120/208-240 3340 14.3 NEMA L14-20P 238 lbs. (108 kg)
220E 3240 14.7 CEE 7/7 Schuko 238 lbs. (108 kg)
240E 3340 13.9 BS-1363 238 lbs. (108 kg)
220-230 (CE) 3240-3541 14.7-15.4 CEE 7/7 Schuko 238 lbs. (108 kg)
230-240 (CE) 3067-3340 13.3-13.9 BS-1363 238 lbs. (108 kg)
ELECTRICAL RATING CHART – GRSDS MODELS - SLANT TRIPLE SHELF
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSDS-24T 120†2015 16.8 NEMA 5-20P 183 lbs. (83 kg)
GRSDS-36T 120/208-240 2685 14.6 NEMA L14-20P 225 lbs. (120 kg)
†Not available in Canada
†Not available in Canada

SPECIFICATIONS
Form No. GRSDM-12077
ELECTRICAL RATING CHART – GRSDS/H MODELS - SLANT/HORIZONTAL DUAL SHELF
* NEMA 5-20P for Canada
Shaded area pertains to Export Models only
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSDS/H-30D 120 1530 12.8 NEMA 5-15P* 140 lbs. (34 kg)
220E 1419 6.5 CEE 7/7 Schuko 140 lbs. (34 kg)
240E 1690 7.0 BS-1363 140 lbs. (34 kg)
220-230 (CE) 1419-1552 6.5-6.8 CEE 7/7 Schuko 140 lbs. (34 kg)
230-240 (CE) 1552-1690 6.8-7.0 BS-1363 140 lbs. (34 kg)
GRSDS/H-30DHW 120/208-240 245012.1 NEMA L14-20P 140 lbs. (34 kg)
GRSDS/H-36D 120 1810 15.1 NEMA 5-20P 158 lbs. (72 kg)
220E 1669 7.6 CEE 7/7 Schuko 158 lbs. (72 kg)
240E 1990 8.3 BS-1363 158 lbs. (72 kg)
220-230 (CE) 1670-1827 7.6-7.9 CEE 7/7 Schuko 158 lbs. (72 kg)
230-240 (CE) 1827-1990 7.9-8.3 BS-1363 158 lbs. (72 kg)
GRSDS/H-36DHW 120/208-240 291014.8 NEMA L14-20P 158 lbs. (72 kg)
120/240 349014.8 NEMA L14-20P 158 lbs. (72 kg)
GRSDS/H-41D 120/208-240 2120 9.1 NEMA L14-20P 178 lbs. (81 kg)
220E 1951 8.9 CEE 7/7 Schuko 178 lbs. (81 kg)
240E 2325 9.7 BS-1363 178 lbs. (81 kg)
220-230 (CE) 1951-2135 8.9-9.3 CEE 7/7 Schuko 178 lbs. (81 kg)
230-240 (CE) 2135-2325 9.3-9.7 BS-1363 178 lbs. (81 kg)
GRSDS/H-41DHW 120/208-240†346017.3 NEMA L14-20P 178 lbs. (81 kg)
High wattage on top shelf only.
†Not available in Canada

8
HORIZONTAL - SINGLE SHELF
Width Depth Height*† Height
Model (A) (B) (C) (D)
GRSDH-24 24" 19-1/2" 12-1/8" 7-1/8"
(610 mm) (495 mm) (308 mm) (181 mm)
GRSDH-30 30" 19-1/2" 12-1/8" 7-1/8"
(762 mm) (495 mm) (308 mm) (181 mm)
GRSDH-36 36" 19-1/2" 12-1/8" 7-1/8"
(914 mm) (495 mm) (308 mm) (181 mm)
GRSDH-41 41" 19-1/2" 12-1/8" 7-1/8"
(1041 mm) (495 mm) (308 mm) (181 mm)
GRSDH-52 52" 19-1/2" 12-1/8" 7-1/8"
(1321 mm) (495 mm) (308 mm) (181 mm)
GRSDH-60 60" 19-1/2" 12-1/8" 7-1/8"
(1524 mm) (495 mm) (308 mm) (181 mm)
SPECIFICATIONS
DIMENSIONS - GRSDH MODELS
HORIZONTAL - DUAL SHELF
Width Depth Height*† Height
Model (A) (B) (C) (D)
GRSDH-24D 24" 19-1/2" 22-1/2" 7-1/8"
(610 mm) (495 mm) (572 mm) (181 mm)
GRSDH-30D 30" 19-1/2" 22-1/2" 7-1/8"
(762 mm) (495 mm) (572 mm) (181 mm)
GRSDH-36D 36" 19-1/2" 22-1/2" 7-1/8"
(914 mm) (495 mm) (572 mm) (181 mm)
GRSDH-41D 41" 19-1/2" 22-1/2" 7-1/8"
(1041 mm) (495 mm) (572 mm) (181 mm)
GRSDH-52D 52" 19-1/2" 22-1/2" 7-1/8"
(1321 mm) (495 mm) (572 mm) (181 mm)
GRSDH-60D 60" 19-1/2" 22-1/2" 7-1/8"
(1524 mm) (495 mm) (572 mm) (181 mm)
A
D
B
B
D
D
C
C
A
* Add 3-1/8"(79 mm) to height for electronic controls.
† Add 3"(76mm) to height when using 4"(102mm) legs.
* Add 3-1/8"(79 mm) to height for electronic controls.
† Add 3"(76mm) to height when using 4"(102mm) legs.
Form No. GRSDM-1207

9
SPECIFICATIONS
SLANT MODEL - SINGLE SHELF
Width Depth Height† Height
Model (A) (B) (C) (D)
GRSDS-24 24" 24" 17-5/8" 8-1/4"
(610 mm) (610 mm) (448 mm) (210 mm)
GRSDS-30 30" 24" 17-5/8" 8-1/4"
(762 mm) (610 mm) (448 mm) (210 mm)
GRSDS-36 36" 24" 17-5/8" 8-1/4"
(914 mm) (610 mm) (448 mm) (210 mm)
GRSDS-41 41" 24" 17-5/8" 8-1/4"
(1041 mm) (610 mm) (448 mm) (210 mm)
GRSDS-52 52" 24" 17-5/8" 8-1/4"
(1321 mm) (610 mm) (448 mm) (210 mm)
GRSDS-60 60" 24" 17-5/8" 8-1/4"
(1524 mm) (610 mm) (448 mm) (210 mm)
DIMENSIONS - GRSDS MODELS
SLANT MODEL - DUAL SHELF
Width Depth Height† Height
Model (A) (B) (C) (D)
GRSDS-24D 24" 24" 29-3/8" 8-1/4"
(610 mm) (610 mm) (746 mm) (210 mm)
GRSDS-30D 30" 24" 29-3/8" 8-1/4"
(762 mm) (610 mm) (746 mm) (210 mm)
GRSDS-36D 36" 24" 29-3/8" 8-1/4"
(914 mm) (610 mm) (746 mm) (210 mm)
GRSDS-41D 41" 24" 29-3/8" 8-1/4"
(1041 mm) (610 mm) (746 mm) (210 mm)
GRSDS-54D 54" 24" 29-3/8" 8-1/4"
(1321 mm) (610 mm) (746 mm) (210 mm)
GRSDS-60D 60" 24" 29-3/8" 8-1/4"
(1524 mm) (610 mm) (746 mm) (210 mm)
B
D
C
C
A
B
C
C
D
D
A
Form No. GRSDM-1207
† Add 3"(76mm) to height when using 4"(102mm) legs.
† Add 3"(76mm) to height when using 4"(102mm) legs.

10
SPECIFICATIONS
Form No. GRSDM-1207
SLANT/HORIZONTAL MODEL - DUAL SHELF
Width Depth HeightHeight *Height
Model (A) (B) (C) (D) (E)
GRSDS/H-30D 30" 24" 33 1/2" 12" 10-3/8"
(762 mm) (610 mm) (851 mm) (305 mm) (264 mm)
GRSDS/H-36D 36" 24" 33 1/2" 12" 10-3/8"
(914 mm) (610 mm) (851 mm) (305 mm) (264 mm)
GRSDS/H41D 41" 24" 33 1/2" 12" 10-3/8"
(1041 mm) (610 mm) (851 mm) (305 mm) (264 mm)
GRSDS/H-30DHW 30" 24" 33 1/2" 12" 10-3/8"
(762 mm) (610 mm) (851 mm) (305 mm) (264 mm)
GRSDS/H-36DHW 36" 24" 33 1/2" 12" 10-3/8"
(914 mm) (610 mm) (851 mm) (305 mm) (264 mm)
GRSDS/H-41DHW 41" 24" 33 1/2" 12" 10-3/8"
(1041 mm) (610 mm) (851 mm) (305 mm) (264 mm) B
D
C
C
A
DIMENSIONS - GRSDS/H MODELS
Height includes 4" (102 mm) legs attached.
SLANT MODEL - TRIPLE SHELF
Width Depth HeightHeight
Model (A) (B) (C) (D)
GRSDS-24T 24" 24" 43 7/8" 8-1/4"
(610 mm) (610 mm) (1114 mm) (210 mm)
GRSDS-36T 36" 36" 43 7/8" 8-1/4"
(914 mm) (914 mm) (1114 mm) (210 mm)
DIMENSIONS - GRSDS MODELS
E
C
A
B
D
D
D
C
Height includes 4" (102 mm) legs attached.
* Optional 15" (381mm) shelf spacing available, adds 3" (76mm) to height of unit.

11
INSTALLATION
ALL MODELS
Glo-Ray®Merchandising Display Warmers are
shipped with most components pre-assembled.
Care should be taken when unpacking shipping
carton to avoid damage to unit and components
enclosed.
WARNING
To prevent any injury or damage to the unit
do not pull unit by power cord.
WARNING
To prevent any injury, discontinue use if power
cord is frayed or worn.
1. Remove unit from box.
2. Remove information packet. To prevent delay
in obtaining warranty coverage, fill out and
mail in the warranty card.
3. Remove tape and protective packaging from all
surfaces of unit.
CAUTION
The National Sanitation Foundation (NSF)
requires units over 36" (914 mm) in length or
weighing more than 80 lbs. (36 kg) to be either
sealed or raised on the installation surface. If
this unit cannot be sealed at the point of use, 4"
(102 mm) legs are included to allow for proper
cleaning access below unit.
WARNING
Do not lay unit on the side with the control panel
or damage to unit could occur.
4. Carefully lay unit on its side and install the four
legs. (Figure 6.)
5. Slide each side glass panel into the upper
channel, then lower the panel into the lower
channel. (Figure 7.)
6. The unit is supplied with product divider bars.
To install them, place the bars in the channels
provided. (Figure 8.) The bars can be readily
adjusted to separate your holding areas as
needed.
LOCATION
NOTE: Unit must be transported in the upright
position.
For proper operation and maximum performance,
locate the Merchandising Display Warmer in an area
where the ambient air temperature is constant
and is a minimum of 70°F (21°C). Areas which are
Figure 8. Installing Product Divider Bars
Figure 6. Leg Installation
Figure 7. Side Glass Panel Installation
Form No. GRSDM-1207
susceptible to active air movements or currents
should be avoided, i.e., near exhaust fans or hoods
and air conditioning ducts.
WARNING
For safe and proper operation, the unit must be
located a reasonable distance from combustible
walls and materials. If safe distances are not
maintained, discoloration or combustion could
occur.
CAUTION
To avoid any injury or damage locate the unit
at the proper counter height, in an area that
is convenient for use. The location should be
level to prevent the unit or its contents from
accidentally falling, and strong enough to
support the weight of the unit and food
displayed.

12
OPERATION
80˚F
28˚C
200˚F
93˚C
Figure 9. Controls
The Merchandising Display Warmer main power
is controlled by the ON/OFF toggle switches
(Figure 9.) Each switch must be in the ON position
for the unit to function.
The thermostat controlled base can be set to any
desired heating level as indicated on the control
plate.
NOTE: Main power toggle switch must be in the
ON position for the heated base to function.
NOTE: If the unit is equipped with LED Temperature
Controls, see ACCESSORIES for operation.
CAUTION
Some exterior surfaces on the unit will get hot.
Use caution when touching these areas to avoid
injury.
WARNING
For safe and proper operation do not place food
product directly onto hardcoat surface. Food
product must be wrapped, boxed or on a food
pan.
CAUTION
Unit is not weatherproof. For safe and proper
operation locate the unit indoors where
the ambient air temperature is constant
and is a minimum of 70°F (21°C).
ON/OFF Toggle Switch Thermostat Control
Form No. GRSDM-1207

13
MAINTENANCE
GENERAL
Hatco Glo-Ray®Merchandising Display Warmers
are designed for maximum durability and
performance, with minimum maintenance.
WARNING
To avoid any injury, turn the power switch OFF,
unplug the unit from the power source and allow
to cool before performing any maintenance.
WARNING
To prevent any injury, discontinue use if power
cord is frayed or worn.
WARNING
To avoid electrical shock or personal injury, do
not steam clean or use excessive water on the
unit.
WARNING
Unit is not waterproof. To avoid electrical shock
or personal injury DO NOT submerge in water.
Do not operate if it has been submerged in
water.
CLEANING NOTICE
Use only non-abrasive cleaners. Abrasive
cleaners could scratch the finish marring its
appearance and making it susceptible to dirt
accumulation.
NOTICE
Only soft cleaning cloths with mild soap and
water should be used to clean breath
protector(s). Breath protector(s) are made of
shatterproof polycarbonate and will scratch or
crack if proper care is not taken.
To preserve the bright finish of the Glo-Ray
Merchandising Display Warmer, it is recommended
that the exterior and interior surfaces be wiped daily
with a damp cloth. Stubborn stains may be removed
with a good non-abrasive cleaner. Hard-to-reach
areas should be cleaned with a small brush and mild
soap.
Clean the glass side panels using a common
glass cleaner.
DISPLAY LIGHT BULB REPLACEMENT
The display light is an incandescent light bulb which
illuminates the warming area. The bulb has a
special coating to guard against injury and food
contamination in the event of breakage.
1. To replace a light bulb, disconnect the power
supply and wait until the unit has cooled.
2. Light bulbs have a threaded base. Unscrew the
light bulb from the unit and replace it with a new
specially-coated incandescent light bulb.
NOTE: Hatco shatter-resistant light bulbs meet
N.S.F. standards for food holding and display areas.
For 120 and 120/208-240 volt applications, use
Hatco part Number 02.30.043.00. For 200, 220,
240, 220-230 and 230-240 volt applications, use
Hatco part Number 02.30.058.00.
WARNING
Only light bulbs which meet or exceed N.S.F.
standards, specifically designed for food
holding areas must be used. Breakage of light
bulbs not specially coated could result in
personal injury and/or food contamination.
WARNING
If service is required on this unit, contact your
Authorized Hatco Service Agent, or contact
the Hatco Service Department at 800-558-0607
or 414-671-6350; fax [phone] or
International fax [phone].
WARNING
This product has no “user” serviceable parts.
To avoid damage to the unit or injury to
personnel, use only Authorized Hatco Service
Agents and Genuine Hatco Replacement Parts
when service is required.
WARNING
Genuine Hatco Replacement Parts are specified
to operate safely in the environments in which
they are used. Some aftermarket or generic
replacement parts do not have the
characteristics that will allow them to operate
safely in Hatco equipment. It is essential to use
Hatco Replacement Parts when repairing Hatco
equipment. Failure to use Hatco Replacement
Parts may subject operators of the equipment to
hazardous electrical voltage, resulting in
electrical shock or burn.
Form No. GRSDM-1207

14
ACCESSORIES
LED TEMPERATURE CONTROL
Units may be equipped with an LED temperature
control device which regulates the base
temperature and also indicates the current base
temperature.
NOTE: This option is factory installed only, not
available for retrofit.
NOTE: Units with the LED temperature control do
not have an additional separate base thermostat. All
temperature regulation is performed by the
controller.
NOTE: Units with LED temperature controls
manufactured for use outside the United States use
devices that indicate temperature in Celsius (°C).
The programming instructions are as follows:
1. To set the temperature, turn the red Mode Switch
counterclockwise to the SP-1 position indicated
on the controller. (Figure 10.)
2. Adjust the Setpoint Screw to the desired
temperature, then turn the red Mode Switch to
the TEMP position. The surface temperature
range is room temperature to 185°F (85°C).
4" (102 mm) ADJUSTABLE LEGS
CAUTION
The National Sanitation Foundation (NSF)
requires units over 36" (914 mm) in length or
weighing more than 80 lbs. (36 kg) to be either
sealed or raised on the installation surface. If
this unit cannot be sealed at the point of use, 4"
(104 mm) legs are included to allow for proper
cleaning access below unit.
WARNING
Do not lay unit on the side with the control panel
or damage to unit could occur.
Carefully lay unit on its side. Install legs to bottom
of unit.(Figure 11.) Hand tighten legs until snug. Do
not overtighten. Return unit to the upright position.
NOTE: Legs are adjustable for leveling the unit. Use
a 5/8" (16 mm) open-end wrench to make leveling
adjustments once the unit is placed in final position.
STAINLESS STEEL SIDE PANELS
Optional stainless steel end panels can be ordered
in place of the glass side panels.
SP1
TEMP ˚F
SP1
Figure 10. Optional LED Temperature Control
Mode
Switch
Setpoint
Screw
Figure 11. Adjustable Legs
Figure 12. Sign Holder
Leg Adjustment
Adjust leg using
a 5/8” (16 mm) open-end
wrench and turning
bottom of leg accordingly. Leg Installation
DISPLAY SIGN HOLDER
A display sign holder (sign not included) is available
for installation on the top or intermediate shelf.
Remove screws from unit and install sign holder
using same screws (See Figure 12.)
BACKLIT SIGN HOLDER
Slant Models 30" - 52"
(762 - 1321 mm) Length Only
A backlit sign holder (sign not included) is available
for installation on the front top shelf.
DESIGNER COLORS
Choose an optional Designer color in place
of the stainless steel exterior finish to match décor.
(Not available for retrofit.)
Form No. GRSDM-1207

WARNINGS
To avoid any injury, turn the power switch OFF,
unplug the unit from the power source and allow
to cool completely before performing any
maintenance or cleaning.
WARNINGS
This product has no “user” serviceable parts. To
avoid damage to the unit or injury to personnel,
use only Authorized Hatco Service Agents and
Genuine Hatco Parts when service is required.
TROUBLESHOOTING
SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION
Light bulb not working. Light bulb defective.
Power turned OFF.
Replace light bulb.
Turn unit ON.
Food cavity not hot enough. Temperature control set too low.
Heating element(s) not working.
Temperature control not working
properly.
Excessive air movement around
unit.
Adjust temperature control to a
higher setting.
Contact Authorized Service
Agent or Hatco for assistance.
Contact Authorized Service
Agent or Hatco for assistance.
Restrict or redirect air movement
(i.e. air conditioning duct or
exhaust fan) away from unit or
install flip-up doors on unit to
contain heat and block air flow.
Food cavity too hot. Temperature control set too high.
Temperature control not working
properly.
Adjust temperature control to a
lower setting.
Contact Authorized Service
Agent or Hatco for assistance.
No heat, but light works. Temperature control set too low.
Heating element(s) not working.
Temperature control not working
properly.
Adjust temperature control to a
higher setting.
Contact Authorized Service
Agent or Hatco for assistance.
Contact Authorized Service
Agent or Hatco for assistance.
No heat and no light. Unit turned OFF.
Circuit breaker tripped.
Turn unit ON.
Reset circuit breaker. If circuit
breaker continues to trip contact
Authorized Service Agent or
Hatco for assistance.
15 Form No. GRSDM-1207

Form No. GRSDM-1207 16
HATCO LIMITED WARRANTY
1. PRODUCT WARRANTY
Hatco warrants the products that it manufactures
(the “Products”) to be free from defects in materials
and workmanship, under normal use and service,
for a period of one (1) year from the date of
purchase when installed and maintained in
accordance with Hatco’s written instructions or
18 months from the date of shipment from Hatco.
Buyer must establish the product’s purchase date by
returning Hatco’s Warranty Registration Card or by
other means satisfactory to Hatco in its sole
discretion.
Hatco warrants the following Product components to
be free from defects in materials and workmanship
from the date of purchase (subject to the foregoing
conditions) for the period(s) of time and on the
conditions listed below:
a) One (1) Year Parts and Labor PLUS One (1)
Additional Year Parts-Only Warranty:
Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Food Warmer Elements (metal sheathed)
Display Warmer Elements
(metal sheathed air heating)
Holding Cabinet Elements
(metal sheathed air heating)
Built-In Heated Well Elements
(metal sheathed)
b) One (1) Year Parts and Labor PLUS Four (4)
Years Parts-Only Warranty on pro-rated
terms that Hatco will explain at Buyer’s
request: 3CS and FR Tanks
c) One (1) Year Parts and Labor PLUS Nine (9)
Years Parts-Only Warranty on: Electric
Booster Heater Tanks Gas Booster Heater
Tanks
THE FOREGOING WARRANTIES ARE
EXCLUSIVE AND IN LIEU OF ANY OTHER
WARRANTY, EXPRESSED OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE
OR PATENT OR OTHER INTELLECTUAL
PROPERTY RIGHT INFRINGEMENT. Without
limiting the generality of the foregoing, SUCH
WARRANTIES DO NOT COVER: Coated
incandescent light bulbs, fluorescent lights, lamp
warmer heat bulbs, glass components, Product
failure in booster tank, fin tube heat exchanger, or
other water heating equipment, caused by liming,
sediment buildup, chemical attack or freezing,
Product misuse, tampering or misapplication,
improper installation or application of improper
voltage.
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy
hereunder will be limited solely, at Hatco’s option,
to repair or replacement by a Hatco-authorized
service agency (other than where Buyer is
located outside of the United States, Canada,
United Kingdom or Australia in which case
Hatco’s liability and Buyer’s exclusive remedy
hereunder will be limited solely to replacement of
part under warranty) with respect to any claim
made within the applicable warranty period
referred to above. Hatco reserves the right to
accept or reject any such claim in whole or in part.
Hatco will not accept the return of any Product
without prior written approval from Hatco, and all
such approved returns shall be made at Buyer’s
sole expense. HATCO WILL NOT BE LIABLE,
UNDER ANY CIRCUMSTANCES, FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES,
INCLUDING BUT NOT LIMITED TO LABOR
COSTS OR LOST PROFITS RESULTING FROM
THE USE OF OR INABILITY TO USE THE
PRODUCTS OR FROM THE PRODUCTS
BEING INCORPORATED IN OR BECOMING A
COMPONENT OF ANY OTHER PRODUCT OR
GOODS.

17
NOTES
Form No. GRSDM-1207

HATCO CORPORATION
P.O. Box 340500, Milwaukee, WI 53234-0500 U.S.A.
[phone] [phone]
Parts & Service Fax [phone] Int’l. Fax [phone]
www.hatcocorp.com
HATCO AUTHORIZED PARTS DISTRIBUTORS
Printed in U.S.A. December 2007
ALABAMA
Jones McLeod Appl. Svc.
Birmingham 205-251-0159
ARIZONA
Auth. Comm. Food Equip.
Phoenix 602-234-2443
Byassee Equipment Co.
Phoenix 602-252-0402
CALIFORNIA
Industrial Electric
Commercial Parts & Service, Inc.
Huntington Beach 714-379-7100
Chapman Appl. Service
San Diego 619-298-7106
P & D Appliance
Commercial Parts & Service, Inc.
S. San Francisco 650-635-1900
COLORADO
Hawkins Commercial Appliance
Englewood 303-781-5548
FLORIDA
Whaley Foodservice Repair
Jacksonville 904-725-7800
Nass Service Co., Inc.
Orlando 407-425-2681
B.G.S.I.
Pompano Beach 954-971-0456
Comm. Appliance Service
Tampa 813-663-0313
GEORGIA
TWC Services
Smyrna 770-438-9797
Heritage Service Group
Norcross 866-388-9837
Southeastern Rest. Svc.
Norcross 770-446-6177
HAWAII
Burney’s Comm. Service, Inc.
Honolulu 808-848-1466
Food Equip Parts & Service
Honolulu 808-847-4871
ILLINOIS
Parts Town
Lombard 708-865-7278
Eichenauer Elec. Service
Decatur 217-429-4229
Midwest Elec. Appl. Service
Elmhurst 630-279-8000
Cone’s Repair Service
Moline 309-797-5323
INDIANA
GCS Service
Indianapolis 317-545-9655
IOWA
Electric Motor Service Co.
Davenport 319-323-1823
Goodwin Tucker Group
Des Moines 515-262-9308
KENTUCKY
Certified Service Center
Lexington 859-254-8854
Certified Service Center
Louisville 502-964-7007
LOUISIANA
Chandlers Parts & Service
Baton Rouge 225-272-6620
MARYLAND
Electric Motor Service
Baltimore 410-467-8080
GCS Service
Silver Spring 301-585-7550
MASSACHUSETTS
Ace Service Co., Inc.
Needham 781-449-4220
MICHIGAN
Commercial Kitchen Service
Bay City 517-893-4561
Bildons Appliance Service
Detroit 248-478-3320
Midwest Food Equip. Service
Grandville 616-261-2000
MINNESOTA
GCS Service
Minneapolis 612-546-4221
MISSOURI
General Parts
Kansas City 816-421-5400
Commercial Kitchen Services
St. Louis 314-890-0700
Kaemmerlen Parts & Service
St. Louis 314-535-2222
NEBRASKA
Anderson Electric
Omaha 402-341-1414
NEVADA
Burney’s Commercial
Las Vegas 702-736-0006
Hi. Tech Commercial Service
N. Las Vegas 702-649-4616
NEW JERSEY
Jay Hill Repair
Fairfield 973-575-9145
Service Plus
Flanders 973-691-6300
NEW YORK
Acme American Repairs, Inc.
Brooklyn 718-456-6544
Alpro Service Co.
Brooklyn 718-386-2515
Appliance Installation
Buffalo 716-884-7425
Northern Parts Dist.
Plattsburgh 518-563-3200
J.B. Brady, Inc.
Syracuse 315-422-9271
NORTH CAROLINA
Authorized Appliance
Charlotte 704-377-4501
OHIO
Akron/Canton Comm. Svc. Inc.
Akron 330-753-6635
Certified Service Center
Cincinnati 513-772-6600
Commercial Parts and Service
Columbus 614-221-0057
Electrical Appl. Repair Service
Independence 216-459-8700
E. A. Wichman Co.
Toledo 419-385-9121
OKLAHOMA
Hagar Rest. Service, Inc.
Oklahoma City 405-235-2184
Krueger, Inc.
Oklahoma City 405-528-8883
OREGON
Ron’s Service, Inc.
Portland 503-624-0890
PENNSYLVANIA
Elmer Schultz Services
Philadelphia 215-627-5401
FAST Comm. Appl. Service
Philadelphia 215-288-4800
Appliance Installation & Service
Pittsburgh 412-809-0244
K & D Service Co.
Harrisburg 717-236-9039
Electric Repair Co.
Reading 610-376-5444
RHODE ISLAND
Marshall Electric Co.
Providence 401-331-1163
SOUTH CAROLINA
Whaley Foodservice Repair
W. Columbia 803-791-4420
TENNESSEE
Camp Electric
Memphis 901-527-7543
TEXAS
GCS Service
Fort Worth 817-831-0381
Armstrong Repair Service
Houston 713-666-7100
Commercial Kitchen Repair Co.
San Antonio 210-735-2811
UTAH
La Monica’s Rest. Equip. Service
Murray 801-263-3221
VIRGINIA
Daubers
Norfolk 757-855-4097
Daubers
Springfield 703-866-3600
WASHINGTON
Restaurant Appl. Service
Seattle 206-524-8200
WISCONSIN
A.S.C., Inc.
Madison 608-246-3160
A.S.C., Inc.
Milwaukee 414-543-6460
CANADA
ALBERTA
Key Food Equipment Service
Edmonton 780-438-1690
BRITISH COLUMBIA
Key Food Equipment Service
Vancouver 604-433-4484
MANITOBA
Air Rite, Inc.
Winnepeg 204-895-2300
NEW BRUNSWICK
EMR Services, Ltd.
Moncton 506-855-4228
ONTARIO
Choquette CKS
Ottawa 613-739-8458
R.G. Henderson Ltd.
Toronto 416-422-5580
QUEBEC
Choquette CKS
Montreal 514-722-2000
Choquette CKS
Québec City 418-681-3944
Parts No. 07.04.301.00 Form No. GRSDM-1207