Havahart 5134G-B User manual

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: [phone]
Certification Exhibit
FCC ID: SNA-RFB
FCC Rule Part: 15.247
IC Radio Standards Specification: RSS-210
ACS Report Number: 10-0086.W03.55.A
Manufacturer: Woodstream Corporation
Model: 5134G-B
Manual

Instruction Manual
Radial-Shape
Wireless Dog Fence
Model 5134G

Co
n
t
r
o
ll
e
r
Congratulations and thank you for choosing the Radial-Shape
Wireless Dog Fence from Havahart®Wireless - the leading innovator
of digital wireless fence solutions.
Featuring breakthrough, patented wireless technology, the Radial-
Shape Wireless Dog Fence is designed to provide maximum freedom
and safety for your dog and peace of mind for you with minimal effort,
investment and impact on your property. It is the industry’s most-
advanced, do-it-yourself, INSTANT-CIRCULAR dog containment system.
It is the first to offer a Roaming Area that can extend from 40 up to
400 feet in all directions with technology housed in a Controller that is
smaller than a Frisbee. There are no wires to bury or break, no back pains
from digging, and no wasted money on trenching —just a fast & easy
setup and freedom for your dog to roam!
Proper training of your dog is the most critical element in ensuring
the successful operation of your wireless dog fence. Consult the
training section of this manual once you have set up your wireless
dog fence.
To ensure your complete satisfaction
and your dog’s safety, please read
and follow all of these instructions
carefully. Should you need
assistance, our Consumer Care
Specialists are ready to help. Call
1-800-800-1819, Option 1.
Thank you for purchasing the
Radial-Shape Wireless Dog Fence
from Havahart®Wireless!
1
Welcome
Havahart®Radial-Shape Wireless Dog Fence
www.havahartwireless.com

2
Table of Contents
Table of Contents
IMPORTANT SAFETY REMINDERS ..........................................................................................................................
SYSTEM COMPONENTS ..............................................................................................................................................
KEY DEFINITIONS, TECHNOLOGY & HOW IT WORKS ....................................................................................
- Roaming Area
- Trigger Zone
- Controller
- Havahart®Collar
GETTING STARTED ........................................................................................................................................................
- Planning Your Wireless Fence System
- Quick Checklist
INSTALLING THE RADIAL-SHAPE WIRELESS DOG FENCE ..............................................................................
Setting Up the Controller .........................................................................................................................
- Installing & Activating the Controller
Setting Up the Collar ...................................................................................................................................
- Installing a Battery
- Checking Battery Status
- Recharging a Battery
- Activating a Collar
- Adjusting the Correction Level of a Collar
- Turning a Collar Off/On
- Removing a Collar
Setting Up the Fence Boundary/Trigger Zone ...............................................................................
- Establishing the Fence Boundary/Trigger Zone Distance
- Placing Training Flags
- Turning the Trigger Zone Off/On
- Display Options
(Viewing Distance to Dog and Battery Status, Turning the Display Off/On, Setting Alarm Options)
Fitting a Collar ................................................................................................................................................
TRAINING YOUR DOG ...................................................................................................................................................
FREQUENTLY ASKED QUESTIONS ............................................................................................................................
FACTORS AFFECTING SIGNAL STRENGTH ............................................................................................................
TROUBLESHOOTING ....................................................................................................................................................
TERMS OF USE AND LIMITATION OF LIABILITY .................................................................................................
WARRANTY INFORMATION ......................................................................................................................................
WIRELESS FENCE PLANNING GRID ..........................................................................................................................
1
2
3
4
Havahart®Radial-Shape Wireless Dog Fence
1-800-800-1819, Option 1
3
4
5
7
9
9
11
14
18
20
27
32
33
36
37
38

To ensure the safe and effective operation of your Radial-Shape Wireless Dog Fence, please read and follow all
safety guidelines and instructions:
sThe Radial-Shape Wireless Dog Fence is designed for dogs older than 6 months that weigh more
than 8 pounds.
sThe Controller must be installed indoors and should not be exposed to moisture (e.g. rain or snow).
sThe Controller must be plugged into a properly grounded 120V AC outlet.
sChanges or modifications to any system component may cause permanent system damage and void
manufacturer warranties.
sTo prevent system damage due to unexpected power surges, it is recommended that you unplug the
Controller from the wall outlet during thunderstorms. All settings will be retained in system memory. Also do
not attempt to install the system during stormy weather.
sTo help prevent skin irritation and increase battery life, do not leave the Collar on your dog for more than
12 consecutive hours.
sAlways remove the Collar from your dog before adjusting any of the system components or settings.
sThe system is intended to provide safe containment of your dog. All components should be kept out of
the reach of children.
sFollow your established leash laws. There may be cases where this system will be prohibited by law.
sProper training of your dog is the most critical element in ensuring the safe and successful operation
of your wireless dog fence.
Important Safety Reminders
Important Safety Reminders
3Havahart®Radial-Shape Wireless Dog Fence
www.havahartwireless.com
DO NOT RETURN THIS PRODUCT
TO THE STORE FOR ANY REASON
CONTACT HAVAHART®WIRELESS DIRECTLY!
CALL 1-800-800-1819, OPTION 1.

Controller
AC Adapter Power Cord
Removable Wall-Mount Adhesive Strips
Screw
Wall Anchor
Collar
2 RCR123A Batteries For Collar
Other Items You May Need:
sScissors
sDrill
sTape Measure
sScrew Driver
sPliers
sPermanent Marker
sIsopropyl Rubbing Alcohol
sSoft Cloth
Extra Set Of Collar Probes For Short-Haired Dogs
Heart-Shaped Collar Tester
75 Training Flags
Battery Recharger
Instructional DVD
Instruction Manual
Quick Setup Guide
System Components
System Components
4
A
A
I
B
J
C
D
E
F
G
H
B
C
D
E
F
G
H
K
J
Model 5134G
Accessories:
sExtra Collar - 5134GX
s25 Flag Pack - HW25FLAGPACK
sHeart-Shaped Collar Tester - HWHEARTSCT
s2 Controller Antennas - HW2ANT
s2 Pack Of Batteries - HW2REBATPACK
sBattery Recharger - HWBATRECHARG
sCollar Battery Cap - HWCBATCAP
s2 Long Probes - HW2LPROBES
s2 Short Probes - HW2SPROBES
sAC Adapter - HWACCORD
Havahart®Radial-Shape Wireless Dog Fence
1-800-800-1819, Option 1
Ensure that the following components are
included with your system. If a component is
missing, please call 1-800-800-1819, Option 1.
K

Controller
Key Definitions:
Roaming Area: Area between the Controller and the Trigger Zone where your dog is free to roam and play.
Capable of expanding from 40 feet up to 400 feet in all directions.
Trigger Zone: The zone, which may be up to 13 feet wide, located outside the Roaming Area that establishes the
fence boundary. Correction is triggered by your dog crossing into the Trigger Zone which can be set to tone-only
(auditory alarm) or static correction. The correction is not constant but cyclical. It will continue through its cycle for
up to 30 seconds while your dog is outside the Roaming Area or until your dog returns approximately 10 feet back
into the Roaming Area.
Controller: Through auditory alerts and an
LCD screen, the Controller provides intuitive
navigation for setting up, activating and
managing your fence. The Controller
houses a state-of-the-art transceiver
and displays the real-time distance to
your dog. It will notify you if your dog
breaches the fence boundary, if there
is a problem with any of the system
components or if the battery life of
the Collar is running low. You can
use your Controller to set and
manage up to 2 Collars.
Havahart®Collar: The comfortable,
water-proof Collar houses a rechargeable
RCR123A battery, two correction Probes and
a state-of-the-art radio transceiver with
advanced antenna assembly. The Collar
communicates continuously with the Controller
to track the real-time location of your dog. Using the
Controller, the Collar can be programmed to tone
only (auditory correction) or one of 5 different static correction
levels depending upon the size, age and temperament of your dog.
The default correction level is tone only. Use long or short Probes depending upon the thickness of your dog’s
coat. The Havahart® Collar features exclusive Integrated Motion Sensor Technology to optimize battery life.
The Technology Behind the System:
The Havahart®Radial-Shape Wireless Dog Fence is driven by two nanoLOC TRX 2.4 GHz transceivers that have been
enhanced with complex algorithms, strategic distortion filtering and modular signal amplification to deliver time-
of-flight ranging technology. These enhancements comprise the core of the patented elements that allow the
Havahart®Radial-Shape Wireless Dog Fence to provide an unparalleled level of technical sophistication in the
wireless dog fencing industry.
Key Definitions, Technology & How it Works
Key Definitions, Technology & How it Works
5Havahart®Radial-Shape Wireless Dog Fence
www.havahartwireless.com

Antennas
LCD Screen
Power Buttton
Antennas
Indicator Light
Battery Container
Battery Cap
Probes
Washers
Up, Enter & Down Buttons
DC Power Connection
How it Works:
Both the Havahart®Collar and the Controller contain nanoLOC TRX 2.4 GHz transceiver chipsets that send and
receive radio transmissions from one another like 2-way radios. When radio signals are sent from the antennas of
either component to the other, they propagate in an omni-directional or spherical manner. The ranging process,
performed by the nanoLOC chipsets with their associated antenna pairs, where data is continuously captured,
filtered and refined, yields the distance between the Havahart®Collar and the Controller.
The Controller is designed so that a custom fence radius of 40 to 400 feet can be set. This radius between the
Controller and the Trigger Zone is what defines the circular Roaming Area for your dog. The Havahart®Collar and
the Controller range continuously to calculate the distance between them so that the system can track the real-
time location of your dog. When the user-defined fence radius distance is reached inside the Trigger Zone, the
Controller sends a command to the Collar to take action and correct (tone or static ---based on user settings). The
Collar will correct your dog until one of these two conditions are met:
1. Your dog returns approximately 10 feet within the Roaming Area.
2. The Collar’s Safety Time-Out Feature stops the correction cycle after 30 seconds.
In the first case, the system automatically returns to normal operating mode. After the correction cycle times out
in the second case, your dog will NOT be corrected for returning to the Roaming Area. The Collar will revert
to normal operating mode only when your dog is at least 10 feet back inside the Roaming Area. After that, the
Controller will not send another correction command until your dog moves back into the Trigger Zone.
Key Definitions, Technology & How it Works
6
A
A
B
B
C
C
D
D
E
E
I
J
K
I
F
FF
G
G
H
H
Controller Features Collar Features
Havahart®Radial-Shape Wireless Dog Fence
1-800-800-1819, Option 1
J
K

Getting Started
Getting Started
7Havahart®Radial-Shape Wireless Dog Fence
www.havahartwireless.com
Plan Your Wireless Fence Boundary:
The most important step in setting up your Havahart®Radial-Shaped
Wireless Dog Fence is determining the proper location to mount the
Controller on a wall. The system creates a circular boundary that can
extend from 40 feet up to 400 feet in all directions from the Controller.
Choose a wall inside your home nearest the center of the desired circular
containment area. This is where you will install the Controller. Be sure
that there is a standard 120V AC power outlet outlet that the 6 foot AC
adapter power cord can reach. Remember, proper training is essential for
your dog to learn the boundary that you set.
Use the Wireless Fence Planning Grid on page 38 to help with positioning
of the Controller.
The following are sample layouts for your reference:
R
O
AMING AREA
Trigger Zone
Trigger Zone
Controller
10’
RO
AMING ARE
A
Trigger Zone
Trigger Zone
Controller
ROAMING AREA
ROAMING AREA
Trigger Zone
Trigger Zone
Controller
R
O
AMING ARE
A
Trigger Zone
Trigger Zone
Controller
10’
Dog has full access to house and yard within the Roaming
Area.
Roaming Area contains part of neighbors’ property and
extends onto the road. Dog will have access to neighbors’
property and to the road. Consequences could be severe.
Dog has limited access to house and yard within Roaming
Area. Collar should be removed upon entering house,
otherwise your dog will be corrected inside the home.
Dog has full access to house and yard within the Roaming
Area.
Good Good
May Cause Problems May Cause Problems
Your Fence Boundary/ Trigger Zone
should NOT be closer than 6 feet to ANY
ROAD, SIDEWALK OR THOROUGHFARE
FOR YOUR DOG’S SAFETY.
!
IMPORTANT MESSAGE

8
Getting Started
Havahart®Radial-Shape Wireless Dog Fence
1-800-800-1819, Option 1
Before you begin the installation process, be sure to check the following:
sMake sure that you have all system components ready and available.
sInsert a new battery in the Collar.
sRead the Quick Setup Guide and watch the instructional DVD.
sCommit to set aside time to properly train your dog.
QUICK CHECKLIST

Setting Up the Controller
Installing & Activating the Controller:
1. Position the Controller inside your home on a wall nearest the
center of your desired containment area. (see Illustration A)
Make sure a standard 120 V AC power outlet is nearby. Mount
the Controller on the appropriate wall, approximately 6 feet
off the ground or at eye level. (see Illustration B)
2. Use the removable wall-mount adhesive strip or screw
& wall anchor to attach the Controller to the wall.
NOTE: It is recommended to use the removable wall mount
adhesive strip in the event that you later determine the
Controller is not in the correct place and it needs to be relocated.
If the strip will not work on the wall of your choice and you want
to get a rough idea of where the Fence Boundary/Trigger Zone
will exist before you attach the Controller to the wall, find a
way to keep the Controller propped upright and as close to the
desired final position as possible.
Make sure the power supply cord will reach the Controller
from a standard electrical outlet.
Installing the Radial-Shape Wireless Dog Fence
9
1
Setting Up the Controller
Sw
in
ROAMING AREA
10’
Illustration A
Illustration B
Havahart®Radial-Shape Wireless Dog Fence
www.havahartwireless.com
Position the controller at least 3 feet
away from large metal objects and major
appliances as these items may reduce the
size and shape of your Roaming Area.
!
IMPORTANT MESSAGE

To attach using the removable wall-mount adhesive strips:
sClean the surface of the desired location of the Controller
with isopropyl rubbing alcohol, wipe gently with a soft cloth
and let dry. DO NOT USE household cleaners. (see Figure 1.1)
sSeparate strips (if still connected) at the perforation.
sPeel the liner from the back of one of the strips and attach it
vertically to the middle of the Controller with the release-tab
pointed upward toward the antennas. (see Figure 1.2a)
sConnect another strip to the strip on the Controller by
pressing the fasteners of both strips firmly together until
they snap. The release-tab on the other strip should point
downward away from the antennas - the opposite direction
of the release-tab of the strip on the Controller (see Figure 1.2b).
sPeel the liner from the back of the other strip and attach it
to the wall with the release-tab facing downward toward the
floor and the Controller antennas facing upward toward the
ceiling. (see Figure 1.3)
To remove the adhesive strips:
sPull the Controller gently from the wall by disconnecting
the fasteners. DO NOT pull the strips off the Controller or
the wall.
sStart with the strip on the wall. Press one hand on the end of
the strip opposite of the release-tab and use your other hand
to pull the release-tab slowly straight down against the wall
stretching it at least 12 inches until the strip releases. Repeat
for the strip attached to the Controller (see Figures 1.4a & b).
10
Setting Up the Controller
3. Plug the Controller (DC power connection located on
the bottom of the Controller) into a nearby standard
electrical outlet.
4. ”Havahart Wireless Fence.” will display (see Screen 1.1)
5. Press “Enter”
Screen 1.1
Figure 1.1
Figure 1.2a
Figure 1.3
Havahart®Radial-Shape Wireless Dog Fence
1-800-800-1819, Option 1
NOTE: When the unit is first activated, you may receive a
“POWER FAILURE DETECTED!!!” warning. Disregard this
message and Press ENTER.
Figure 1.4a
NOTE: The removable wall-mount adhesive strips are not
recommended for wallpaper. Apply to surfaces above 50˚F .
Adhesive could soften and lose adhesion above 105˚F.
Figure 1.2b
Figure 1.4b

11
Setting Up the Collar
2
Setting Up the Collar
Installing the Radial-Shape Wireless Dog Fence
Havahart®Radial-Shape Wireless Dog Fence
www.havahartwireless.com
The Collar should not be placed on your
dog until after you have successfully
installed it on the system.
Install one Collar at a time. The system
allows you to activate up to 2 Collars.
The default correction level of the Collar
is set to Tone Only, which you need to use
to set up your fence boundary.
!
IMPORTANT MESSAGE
Figure 1.
Battery Installation
CR123A 3V +
-
Screen 1.3
Screen 1.2
Screen 1.4
Installing a Battery:
1. Make sure a battery is fully charged before installing it in the
Collar (see Recharging a Battery). Turn the battery cap on the
Collar counterclockwise about 1/4 turn and pull it out. With the
positive side facing outward, install one RCR123A battery into
the Collar. (see Figure 1.5) Replace the battery cap and turn it
clockwise to lock it in place.
2. A green light should flash every 5 seconds. If it does not, check
the direction that the battery was installed --- positive side
should be facing outward.
NOTE : The Collar is always “on” when a good battery is installed. However,
the Collar may be awake or asleep. Integrated Motion Sensor Technology
allows the Collar to conserve battery life when appropriate by putting the
Collar to sleep. The light on the Collar will not flash when the Collar is
asleep. Movement, such as gently shaking the Collar, will awaken it and
the green light will flash. A red light will flash to indicate that the battery
needs to be recharged. The Controller will also produce an auditory tone
to alert you that the battery is low.
Checking Battery Status:
1. Select “Display Options” (see Screen 1.2)
2. Select “Show Collar Monitor” (see Screen 1.3)
Battery
Status Collar is:
NA Asleep to conserve battery life
OK Battery life is shown as a percentage (see screen 1.4). When a
battery needs to be recharged, a Low Battery Alert will
appear (see screen 1.5).
LOW Awake, but battery needs to be recharged soon
Screen 1.5

12
Setting Up the Collar
Havahart®Radial-Shape Wireless Dog Fence
1-800-800-1819, Option 1
Activating a Collar:
1. Hold the Collar within 6 feet of the Controller
2. On the Controller...
sSelect Setup Menu (see Screen 1.6)
sSelect Collar Setup (see Screen 1.7)
sSelect Add a Collar (“Searching for new Collars... ” will
appear on screen (see Screen 1.8)
sGently move or shake the Collar to keep it awake. The
flashing green light will confirm that it is awake.
s“New Collar Found! Collar ID=1” will appear on screen
sPress Enter
sRepeat this process to add more Collars.
3. If no Collar is found, check that the above steps were
completed, the battery is correctly installed, the Collar is
active (green light is flashing) and within 6 feet of the
Controller - then repeat Step 2 again.
Screen 1.6
Screen 1.8
Screen 1.7
NOTE : If using more than one Collar, mark each using a
permanent marker to indicate which is Collar 1 and
which is Collar 2.
Recharging a Battery:
-Remove the low battery from the Collar
-Make sure the battery recharger is properly connected to a grounded
120V AC outlet
-Properly orient the battery in the recharger with the positive side closest
to the lights of the recharger
-Remove the battery when recharging is complete
Recharging Light Colors:
Blue - when on standby (no battery in chamber),
- when the battery is in the chamber the wrong way
- when the battery is fully charged
Red - when the battery is charging
You want to see the red light come on when you place the battery in the recharger. You can charge up to two batteries
at the same time. When the battery is close to being fully charged, the light will flicker red and blue. Do NOT take the
battery out until the light turns full blue. It takes less than 3 hours to fully charge a battery.
Note: Recharging the RCR123A battery is similar to recharging a mobile phone. Always have a spare battery ready to go
when your other battery gets low.
Warning: Do NOT put a non-rechargeable battery in
the battery recharger.
Correct way to
Insert a Battery in
the Recharger.
+
-

13
Setting Up the Collar
Installing the Radial-Shape Wireless Dog Fence
Havahart®Radial-Shape Wireless Dog Fence
www.havahartwireless.com
Turning a Collar Off/On:
1. Hold the Collar within 6 feet of the Controller
2. On the Controller...
sSelect Setup Menu (see Screen 1.6)
sSelect Collar Setup (see Screen 1.7)
sSelect Correction Level (see Screen 1.8)
sSelect Turn Collar off/on (see Screen 1.9)
sPress Enter
Removing a Collar:
1. Hold the Collar within 6 feet of the Controller
2. On the Controller...
sSelect Setup Menu (see Screen 1.6)
sSelect Collar Setup (see Screen 1.7)
sSelect Delete a Collar (see Screen 1.8) - If you have more than
one Collar installed, select the number of the Collar that you
would like to remove
sSelect YES
sSelect OK
sSelect OK Again
Screen 1.9
Screen 1.8
Screen 2.1
Adjusting the Correction Level of a Collar:
1. Hold the Collar within 6 feet of the Controller
2. On the Controller...
sSelect Setup Menu (see Screen 1.6)
sSelect Collar Setup (see Screen 1.7)
s
Select Correction Level - If you have more than one Collar installed,
select the number of the Collar that you would like to change
(see Screen 1.8)
sSelect Correction Level (see Screen 1.9)
sUse the up or down arrow keys to choose the desired
correction level. 5 is the highest static correction level. 1 is
the lowest static correction level. Tone Only is the auditory
correction level (sound only). (see Screen 2.0)
sPress Enter
sSelect Ok
The correction level of the Collar may
be adjusted using the Controller based
on the size, age and temperament of
your dog. There are 5 static correction
levels and one tone level (sound only).
The default correction level of the
Collar is Tone Only.
It is recommended to start with a
lower correction level when training
your dog.
You may need to gently move or shake
the Collar to keep it awake so that it will
accept changes from the Controller.
The flashing green light will indicate
that it is awake.
!
IMPORTANT MESSAGE
Screen 2.0

14
Setting Up the Fence
Boundary/Trigger Zone
3
Setting Up the Fence Boundary
F
e
n
c
e
B
o
u
n
d
a
r
y
/
T
r
i
g
g
e
r
Z
o
n
e
Illustration D
Havahart®Radial-Shape Wireless Dog Fence
1-800-800-1819, Option 1
Establishing the Fence Boundary/Trigger Zone Distance:
1. Estimate the distance between the Controller and the
desired boundary location. This distance will be the radius
of the Trigger Zone all the way around the Controller.
TIP : Use the shortest distance to a physical boundary as a
starting point for the radius of the Trigger Zone (see Illustration C).
2. Set the radius on the Controller
sFrom the Set Up Menu, select Fence Setup (see Screen 1.7)
sUse the up/down arrow to scroll to the desired radial
distance and press Enter. The minimum radius is 40 feet,
and the maximum radius is 400 feet from the Controller
in all directions (see screen 2.1).
sSelect OK to Save Your Settings
3. Test the Trigger Zone
sTo confirm that the location of the actual boundary is
correct...
- Hold the Collar by the strap with your arm fully
extended down by your side (see Figure 1.6). Make
sure that your body does not get between the Collar
and the Controller as your body may affect the signal
and cause the boundary to shift inward (see Factors
Affecting Signal Strength on page 32).
- Walk toward the boundary while gently moving the
Collar until the Collar beeps and the Collar light flashes
red. To confirm that the distance is correct, step back 6
feet until the Collar stops beeping and then walk in the
same direction until the Collar beeps and the Collar light
flashes red again. Note how far from desired location
the actual setting is.
4. Adjust the Fence Distance on the Controller accordingly
using the instructions in Step 2 until the desired boundary
location is established.
TIP : Place a flag at the boundary location (see Illustration D).
Your Trigger Zone should be NO closer
than 6 feet to ANY ROAD, SIDEWALK
OR THOROUGHFARE FOR YOUR DOG’S
SAFETY.
The actual distance from the Trigger
Zone to the Controller may be less than
the set radius. This reduced boundary
may be the result of Factors Affecting
Signal Strength (page 32).
!
IMPORTANT MESSAGE
ROAMING ARE
A
10’
Figure 1.6
Illustration C

Controller
Installing the Radial-Shape Wireless Dog Fence
Setting Up the Fence Boundary/Trigger Zone
15
Placing Training Flags:
Once your boundary is established, it’s time to place the Training Flags.
Training Flags are critical for the effective training of your dog and
should be placed every 6 feet at the fence boundary to enclose the
Roaming Area, where it will be safe for your pet to roam and play.
1. Hold the Collar by the strap or grey battery container. Do not hold
the area where the strap meets the Collar on either side as this is
where the antennas are located (see the raised areas of the strap)
and your hand may interfere with the signal. Fully extend your arm
down by your side. Make sure that your body does not get between
the Collar and the Controller as your body may affect the signal and
cause the boundary to shift inward (see Factors Affecting Signal
Strength on page 32).
2. Walk toward the boundary while gently moving the Collar until
the Collar beeps and the Collar light flashes red (see Figure 1.7). To
make sure that the distance is correct, step back 6 feet into the
Roaming Area until the Collar stops beeping and then walk
forward in the same direction until the Collar beeps and the
Collar light flashes red again. ( see Illustration E )
The fence boundary may not form a
perfect circle. Large metal objects such
as a car or refrigerator can slightly distort
the roundness of your fence boundary.
However, once set, the boundary location
will remain consistent over time.
(see Factors Affecting Signal Strength
on page 32. )
Havahart®Radial-Shape Wireless Dog Fence
www.havahartwireless.com
IMPORTANT MESSAGE !
F
e
n
c
e
B
o
u
n
d
a
r
y
/
T
r
i
g
g
e
r
Z
o
n
e
Illustration E
TIP : 6 feet is about 2 paces.

16
4. Repeat this process by walking toward the fence boundary
(about 6 feet over from the last flag), placing a flag, and
then stepping back into the Roaming Area until the entire
containment area is surrounded. (see Illustration E.)
NOTE: These flags represent the location of your wireless
fence and will be used later to train your dog. Be sure that
the flags form an enclosed area and that your dog has safe,
adequate entry to your house.
Turning the Trigger Zone Off/On:
1. Navigate to the Menu where Setup Menu and Display
Options are listed. (see Screen 2.3)
2. Press the blue flashing Power Button to Turn Off the
Trigger Zone. (see Screen 2.4)
3. Press the Power Button again to Turn On the
Trigger Zone.
NOTE: All settings will be retained in system memory
when you Turn Off the System.
Setting Up the Fence Boundary/Trigger Zone
Placing Training Flags: (continued):
3. Place a Boundary Training Flag in the ground (see Figure 1.8).
Move back into the Roaming Area until the Collar stops beeping.
TIP: If hard ground makes it difficult to place a flag, use a
screwdriver to poke a hole in the ground, place the flag in
the new hole and make sure it is upright.
Screen 2.3
Screen 2.4
Po
Po
P
P
Po
Po
o
we
we
w
e
w
we
we
we
w
w
e
r
r
r
r
r
r
Havahart®Radial-Shape Wireless Dog Fence
1-800-800-1819, Option 1
Figure 1.7
Figure 1.8
!
IMPORTANT MESSAGE
If you have difficulty hearing the tone of the
Collar, you can use the Heart-Shaped Collar
Tester to visually confirm the boundary.
Hold the metal contact points located inside
the holes of the Heart-Shaped Collar Tester
against the Probes of the Havahart®Collar
so that metal is touching metal. Carry the
Havahart®Collar by the grey battery container
of the Collar with the Heart-Shaped Collar
Tester held against the Probes. Fully extend
your arm down by your side. Make sure that
your body does not get between the Collar
and the Controller as your body may affect
the signal and cause the boundary to shift
inward. Walk to a boundary point and watch
the Heart-Shaped Collar Tester illuminate.

17
Installing the Radial-Shape Wireless Dog Fence
Display Options
Display Options:
Viewing Distance to Dog and Battery Status: (see Screen 2.7)
sSelect Display Options (see Screen 2.5)
sSelect Show Collar Monitor (see Screen 2.6)
NOTE: See Battery Status Level meanings on page 11.
Turning the Display Off/On: (see Screen 2.6)
sSelect Display Options (see Screen 2.5)
sSelect Display Off (see Screen 2.6)
sPress Enter to turn display back on
Setting Alarm Options:
Set Alarm Volume Level: (see Screen 2.8)
sSelect Display Options (see Screen 2.5)
sSelect Alarm Options (see Screen 2.6)
sSelect Alarm Volume Level (see Screen 2.8)
sUse the up or down arrow keys to choose the desired alarm
level. Select HIGH, LOW, or OFF (see Screen 2.9)
sPress Enter
sSelect OK to save
NOTE: It is recommended to select HIGH.
Turning Boundary Breach Alert Off/On: (see Screen 3.0)
sSelect Display Options (see Screen 2.5)
sSelect Alarm Options (see Screen 2.6)
sSelect Boundary Breach (see Screen 2.8)
sUse the up or down arrow keys to turn the boundary breach
alert OFF or ON (see Screen 3.0)
sPress Enter
sSelect OK to save
NOTE: It is recommended to keep the Boundary
Breach Alert ON.
Screen 2.7
Screen 2.8
Screen 2.9
Screen 3.0
Havahart®Radial-Shape Wireless Dog Fence
www.havahartwireless.com
Screen 2.5
Screen 2.6

Fitting a Collar
To ensure safe and effective operation of the system, it is
important to make sure that the Collar is fitted properly.
1. Be sure the fence is turned off at the Controller.
(see page 16)
2. With your dog standing comfortably, position the Collar
high on your dog’s neck, underneath the chin with the
Probes facing upward centered on your dog’s neck. The
word “Havahart®” should be right side up when you look
at your dog.
3. Make sure the Probes maintain contact with skin.
sCollar is factory installed with long Probes for thick or
long-haired breeds.
sShort Probes for short-haired dogs are included
sTo change the Probes, simply unscrew the long Probes
and replace them. Be sure the rubber washer is
between the probe and the grey battery container.
Use your fingers to tighten the Probes as far as you can.
Do not over tighten.
5. Adjust the Collar to fit snugly but not tightly. You should
be able to slide the tip of one finger between your dog’s
coat and one of the Probes on the Collar. The tip of your
finger should not be able to slip between the two easily,
but with some effort. It should be a tight squeeze.
Separately, you should be able to slide one finger
between the strap of the Collar and the back of your
dog’s neck. (see Figure 1.9)
6. Once the Collar is adjusted to correct length, remove the
Collar and trim the excess using scissors. (see Figure 2.0)
4The Collar should be snug enough so that
it does not move when your dog moves.
To help prevent skin irritation, it is
recommended that you never leave
the Collar on your dog for more than
12 consecutive hours at a time.
Figure 1.9
Figure 2.0
IMPORTANT MESSAGE !
NOTE: If your dog is going to continue to grow or grows a
long winter coat, leave extra room before trimming off
the excess.
NOTE: It may be necessary to trim the hair around the
Probes to ensure reliable contact.
Fitting a Collar
18
Havahart®Radial-Shape Wireless Dog Fence
1-800-800-1819, Option 1