Havis-Shields 2006-2007 Dodge Charger and Magnum... Configuration guide

INSTALL INSTRUCTIONS
C-VS-2400-CHGR & C-VS-2400-CHGR-1
2006 – 2007 DODGE CHARGER and MAGNUM
2008 DODGE CHARGER and MAGNUM
TOOLS REQUIRED:
Ratcheting wrench
Sockets - 7/16”, 10mm, 8mm
Screwdriver set
T-20 Torx bit
HARDWARE:
ITEM QTY DESCRIPTION PART#
1 1 Console housing assembly C-VS-2400-CHGR-H
2 1 Front support bracket CM001593
3 2 Side trim panels - 2006 – 2007 Charger CM001598-D and P
3 2 Side trim panels - 2008 Charger CM002164 and CM002165
4 1 Front floor bracket CM001595
5 1 Sensor guard CM001638
6 1 Rear floor panel CM001642
7 6 #10 x ½” machine screws GSM33118
8 2 #10 keps nuts GSM30028
9 4 #10 flat washers GSM31003
10 4 ¼” flat washer GSM31005
11 4 ¼” x ½” carriage bolt GSM31999
12 4 ¼” Nylock nut GSM30016
2 ¼” x ¾” self threading bolt GSM33060-1
2 ¼” x 1” fender washer GSM31014
2 6mm hex nut GSM30201
1 1-1/16” diameter plug GSM20017-1
1 Hardware Kit C-HK
1 Torx Hardware Kit C-HK-1
10, 11, 127, 9
7, 9
1
6
5 - Not shown, approximate location
4
3
2

C-VS-2400-CHGR_INST_12-07
2
Always!
 Read all instructions before installing any Havis-Shields Equipment Corp products.
 Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
 Use hardware provided with install kit
 For product support, visit the Install Instructions Section of our website at
http://havis.com/Installation/Installation.html, email [email protected] or call 1-800-
524-9900.
2006-2007 Charger OEM Setup Remove OEM track/plate &
plastic trim covering
Loosely attach, (driver side 1st),
front support bracket to OEM
b
racket located under radio controls.
Use #10 x ½” screw & keps nut
(Item 2, 7, 8, 9)
Attach passenger side, and tighten
hardware on both sides
(Item 2, 7, 8, 9)
Attach front floor bracket to front
support bracket and floor of vehicle
using #10 x ½” machine screws,
washers, and reuse OEM floor nuts or
supplied 6mm nuts and fender washers
(Item 2, 4, 7, 9)
OEM or 6mm
hardware
Note. To avoid crushing harness
route cable over top of floor
bracket
Note: Due to some sli
g
ht di
ff
erences on the OEM
f
loor mount bracket, tabs with mountin
g
hole ma
y
need to be bent slightly to accommodate the console front support bracket. Bending these tabs can
easily be done using pliers.

C-VS-2400-CHGR_INST_12-07
3
Position sensor guard to align
with OEM floor nut serts
(Item 5)
Position rear-floor panel, continue to
align with OEM floor nut serts
(Item 6)
Place console housing assembly,
continuing to align with OEM
floor nut serts (Item 1)
Using OEM rear bolts or ¼” x ¾” sel
f
threading bolts, loosely attach main
console housing, sensor guard, and
rear cover panel to floor
(8mm or 7/16” socket)
Attach main console housing to
previously installed floor bracket
using ¼” carriage bolts and nylock
nuts. Use a scribe or awl to help align
(7/16” socket, awl)
Tighten all hardware
(7/16”, 8mm, 10mm socket)
Attach side trim panels using #10 x ½”
machine screw & washer
(Phillips screwdriver) (Item 3)
Wire and mount
equipment controls
2006 - 07 2008