Hay BOWLER TABLE 185664 User manual

INSTRUCTION MANUAL
BOWLER TABLE
By Shane Schneck

Shane Schneck’s Bowler Table is a compact side
table that is ideal for small spaces. The single tube
that extends upwards creates a defined profile,
which doubles as a functional handle too. The
stem, handle and tray are made in powder coated
steel, with a solid granite base that provides
stability, yet it is still lightweight enough to move
around. Bowler comes flat packed and is easy
to assemble, making it suitable for all kinds of
domestic and corporate environments.
INTRODUCTION

CAUTION
With a little care you can prolong the life of your
furniture. Follow the instructions for the materials of
your specific product to make sure that it stays in
the best shape for as long as possible.
The information below is only intended as a general
guideline. For more information on how to remove
specific stains, please enquire where you bought
the furniture.
• Always remove stains quickly before they can do
any permanent damage to the furniture.
• When you move the table, make sure you lift it
rather than pulling or pushing it to avoid damaging
the floor, legs and mountings.
• Use coasters under damp, hot or coloured objects
to avoid permanent stains.
• Be careful not to scratch or damage the surface
with sharp objects.
• Avoid improper use such as putting your feet on
the table or standing on it.
CARE AND MAINTENANCE

POWDER COATED STEEL
• Wipe with a clean cloth wrung in water or in a
solution of water and a neutral detergent. Remove
soap residue immediately using a clean, dry cloth.
• Avoid using scouring cream or scouring pads, as
they may scratch the surface.
• Do not use solvents as they may have an adverse
effect on the coating.
• Never use acetic acid or citric acid.
GRANITE
• As granite is a natural material, each stone has
unique colours, patterns and textures. Therefore, the
surface’s colour and finish may vary slightly from
product to product.
• Wipe with a clean cloth wrung in water or in a solu-
tion of water and a neutral detergent, soap flakes or
stone soap. Remove soap residue immediately using
a clean, dry cloth.
• Using excessive cleaning products can leave a film
and cause streaks.
• Avoid using scouring cream or scouring pads, as
they may scratch the surface.
• Never use vinegar, ammonia, acetic acid or citric
acid or abrasive cleaners.
• To optimally maintain the naturally beautiful
appearance of the granite, we recommend you reg-
ularly treat the furniture’s surface with stone soap
or soap flakes. With regular treatment, the surface
will gradually gain a higher resistance to stains and
acquire a silkier, more matte look.
CARE AND MAINTENANCE

Tube (B)Tray (A)
Allen Key Large (I) Allen Key Small (J)Screw (G) Screw (H)
PARTS
Granite base (C) Plastic washer (F)Spring washer (D) Washer (E)

1.
Insert the tube (B) into the granite base (C). Make sure the small hole on top of the tube is facing the
long side of the granite base. Insert the screw (H), spring washer (D) and washer (E) from the bottom, and
secure them with the large Allen key (I). Wait until the next step before fully tightening the screw.

2.
To fully fasten the screw, turn the base upside down in your lap to get a good
grip, and then tighten the screw completely.

3.
Mount the plastic washer (F) to the pin on the bottom of the tray (A).

4.
Insert the tray’s pin (A) into the tube (B).
Secure the connection by fastening the screw (G) with the small Allen key (J).
Make sure the long side of the tray is facing the long part of the base.
Re-tighten both bottom and top screws after the table has been fully assembled.

5.

Havnen 1 8700 Horsens Denmark
[phone] / [e-mail]
ITEM NO. 706377
25012019