Heatilator CFL-18NG User manual

1
LOG #1 & #2: (SRV481-766)
Setlogs#1and2infrontoftheburner. Rest
the bottom two notches over the extended
material of the burner legs. Slide it towards
the burner until it comes in contact with the
burner.
481-925C 3/04
LOG #3 & #4: (SRV481-755)
NOTE:An additionalpiece of INSULATION
is shipped with your log set. If this piece is
missing,DONOTPROCEED. Callyourdeal-
er. Following theinstructions givenbelow is
very important (Flat spots will guide you
throughout the process). Use the log num-
berstoidentifythe logs. Check to make sure
the tabs on the side of burner legs are bent
outward. After setting burner, place insula-
tionprovidedwithlogsetbeneathburneras-
semblyandabove valve. Make surevalveis
totallycovered.WARNING: Failure to doso
willcause the unitto malfunction and create
apotentialdangeroussituation.Set og grate
byresting it downandsliding it towardburn-
er. Make sure right and left grate bars slide
onoutsideofburnerlegsbetweentabs.Place
“dime size” pieces of mineral wool on the
topof the burner,spaceddimes widthapart.
Set logs #3 and 4 between the grate and
logs #1 and 2 with the bark detail towards
the outside. Logs #3 and 4 should be even
withlogs#1and2fromoneside to the other.
Slide grate to hold log in place.
1 3
1
3
INSULATION
1
3
BRACKETS
(For use to place log #5)
LOG PLACEMENT INSTRUCTIONS
Models: CFL-18NG/LP
CFL-18NG/LP-B
2 4
5 6 7 8 9 10
4
4
2
2

2
LOG #7: (SRV446-702)
LOG #6: (SRV481-705)
LOG #5: (SRV481-701)
This log sits towards the back on top of the
bracketslocated on theright and theleft. The
two notches on the bottom of the log should
rest over these brackets. For NG units the
back of this log should line up with the back
end of the brackets. For LP units the back of
this log should be recessed a 1/2-inch from
the back of the brackets.
Setlog#6onthe topoflog#1andtheburner
towardstheleftbyfollowingtheflatspotmark
(onlog #1). Makesurethat the logwill clear
the ports on the top of the burner.
Set log #7 on the top of log #2 to the right
(use flat spot). The pointed end should be
towardsthecenteroftheburner,andshould
rest underneath the pointed end of log #6.
(Youshouldtiltuplog#6whileyouaredoing
that). Make sure that the log will clear the
ports on the top of the burner.
5
6
5
6
77
FLAT SPOT (For use to place log #6)
FLAT SPOT (For log #7)
FLAT SPOTS (For log #8)

3
LOG #10: (SRV446-706)
LOG #9: (SRV402-701)
LOG #8:
Holdlog #8 with the barkdetail towards the
left.Lay the backend of thislog on theright
flat spot located on the top of the back log.
Restthe front endof this logon the flatspot
to the left of the burned area of log #1.
Hold log #9 with the pointed end towards
the back and the bark detail towards the
top.Set the frontendon the flatspots of log
#2 towards the right, then lay the back end
(pointedend)onto the flat spot ofthecorner
of log #8.
Hold log #10 with bark detail towards the
top and the burned area towards the right.
Set the back end of the log on the left flat
spot located on the top of log #5. Rest the
front end of the log on the top flat spot of
log #6. 10
9
8
9
8
10
FLAT SPOTS (For log #10)
FLAT SPOTS (For log #9)