Heatilator ST-CFL-24NG User manual

1
NOTE: Followingtheinstructionsgivenbe-
low is very important (Flat spots will guide
you throughout the process). Use the log
numbers to identify your logs. Check to
makesurethetabsonthe side oftheburner
legsare bentoutward.Aftersettingtheburn-
er, set the identical log grates one on each
sideoftheburner. Set them down and slide
eachonetowardburner.Makesurerightand
leftgratebarsslideon outside of the burner
legs. Push the grate toward burner. Place
“dimesize”piecesofmineralwoolontopof
burner, spaced dimes width apart. For log
placement place each log standing at the
correct side of burner. Please refer to the
side desired prior to each log setting.
LOG #1: (SRV569-710)
Standingatthe side opposite the valve, set
log #1 in front of the burner, between the
burner and the grate with the bark detail
facingawayfrom the burner. Pushthegrate
along with the log to come in contact with
theburner.
569-925D 4/04
LOG #2 & #3: (SRV569-711)
Standingat thevalveside,set log#2and#3
on the other side of the burner. Rest the
bottomtwonotchesover extended material
oftheburner leg. Push theloguntilit comes
in contact with the burner.
2
1
1
2
LOG PLACEMENT INSTRUCTIONS
Model: ST-CFL-24NG/LP
33

2
LOG #7: (SRV569-709)
LOG #6: (SRV569-708)
LOG #4 & #5: (SRV481-755)
Standing at the valve side, set logs #4 and
5 between the grate and logs #2 and 3 with
the bark detail towards the outside. Logs
#4 and 5 should be even with logs #2 and 3
from one side to the other. Slide gate to
hold in place.
Standing at the side opposite of the valve,
setlog#6onthetopoflog#1andtheburner
to the left by following the flat spot pattern.
Standingat the valve side, set log #7 on the
top of log #2 and the burner to the left by
followingthe flat spots pattern.
4
6
7
7
6
4
FLAT SPOTS (For log #8)
FLAT SPOTS (For log #7)
FLAT SPOT (For log #6)
5
5

3
LOG # 10: (SRV569-707)
LOG #9: (SRV569-706)
LOG #8: (SRV569-704)
Standingatthesideoppositeofthevalve,set
log #8 on th top of logs #1 and 7 (across the
burner)byfollowingtheflatspotpattern.Note:
The narrower end is on the top of log #1.
Standing at the valve side, set log #9 on
the top of log #3 to the right, using the flat
spot on log #3. Lay the log on the top and
across log #8, using the flat spot pattern.
Standing at the side opposite of the valve,
set log #10 on the top of log #1 to the right
using the flat spot on log #1. Lay the log to
rest on the top of log #8. When this log is
placed it rests on the flat spot in the corner
of log #8.
8
9
10
8
9
10
FLAT SPOTS (For log #9)
FLAT SPOTS (For log #10)
FLAT SPOTS (For log #11)

4
LOG #13: (SRV569-705)
LOG #12: (SRV569-703)
LOG #11: (SRV569-702)
Standingatthe side opposite the valve, set
log #11 on the top and across logs #9 and
6, using the flat spots on these logs.
Standing at the side opposite of the valve,
set log # 12 on top and across logs # 6 and
9, using the flat spots on these logs.
Standing at the valve side, set log # 13 on
thetop of log # 3 using the flat spot on log #
3. Lay it onto the flat spot of log #9, this log
curves to the right.
11
12
13
13
12
11
FLAT SPOTS (For log #13)
FLAT SPOTS (For log #12)