Heatilator CFL-24NG User manual

Heat & Glo • CFL-24NG/LP, CFL-24NG/LP-B, CFL-24NG/LP-C • 481-926 Rev. E • 9/21 1
LOG PLACEMENT
INSTRUCTIONS
Log Set Assembly:
Models: CFL-24NG/LP
CFL-24NG/LP-B
CFL-24NG/LP-C
33
11
44
22
55
3311
881010
66
44
77
22
99
55
BRACKETS
(Use to place log #5)
LOG #1 & #2: (SRV481-766)
Set logs #1 and 2 in front of the burner. Rest the bottom
two notches over the extended material of the burner legs.
Slide it towards the burner until it comes in contact with
the burner.
LOG #3 & #4: (SRV481-755)
Set logs #3 and #4 between the grate and logs #1 and 2
with the bark detail toward the outside. Logs #3 and #4
should be even with logs #1 and #2 from one side to the
other. Slide grate to hold log in place.
LOG #5: (SRV481-701)
This log sits toward the back on top of the brackets located
on the right and the left. The two notches on the bottom of
the log should rest over these brackets. The back of this
log should line up with the back end of the brackets.
FLAT AREA (Use to place log #6)
LOG #6: (SRV481-705)
Set log #6 on the top of log #1 and the burner toward the
left by following the at area mark (on log #1). Make sure
that the log will clear the ports on the top of the burner.
FLAT AREA (For log #7)
66
BURNER STYLE MAY VARY
Follow the instructions for log placement using gures
and instructions below. Use the “at areas” indicated in
the photos to guide you through the process. Use the
log numbers to identify the logs. Check to make sure
the tabs on the side of burner legs are bent outward. Set
log grate by resting it down and sliding it toward burner.
Make sure right and left grate bars slide on outside of
burner legs between tabs.
CAUTION: Carefully remove the logs from the
packaging. Logs are fragile!
NOTICE: To simplify the installation process,
positively identify each individual log before
beginning installation.
NOTICE: Burner styles may vary.

Heat & Glo • CFL-24NG/LP, CFL-24NG/LP-B, CFL-24NG/LP-C • 481-926 Rev. E • 9/21 2
LOG #7: (SRV446-702)
Set log #7 on the top of log #2 to the right (use at area).
The pointed end should be toward the center of the burner,
and should rest underneath the pointed end of log #6.
Tilt up log #6 to accommodate the placement of log #7.
Make sure that the log will clear the ports on the top of
the burner.
88
1010
77
99
FLAT AREAS (For log #8)
LOG #8: (SRV481-703)
Hold log #8 with the bark detail toward the left. Lay the back
end of this log on the right at area located on the top of
the back log. Rest the front end of this log on the at area
to the left of the burned area of log #1.
LOG #10: (SRV446-706)
Hold log #10 with bark detail toward the top and the
burned area toward the right. Set the back end of the log
on the left at area located on the top of log #5. Rest the
front end of the log on the top at area of log #6.
LOG #9: (SRV402-701)
Hold log #9 with the pointed end towards the back and
the bark detail towards the top. Set the front end on the
at areas of log #2 toward the right, then lay the back end
(pointed end) onto the at area of the corner of log #8.
FLAT AREAS (For log #10)
FLAT AREAS (For log #9)

Heat & Glo • CFL-24NG/LP, CFL-24NG/LP-B, CFL-24NG/LP-C • 481-926 Rev. E • 9/21 3
Install Mineral Wool
Remove the mineral wool from the packaging and place
dime size pieces on the top of the burner, spaced a dime’s
width apart. Care should be taken to avoid placing ember
material directly over ports and to avoid using excessive
amounts of ember material.
WARNING! Risk of Explosion! Follow ember placement
instructions. DO NOT place embers directly over burner
ports. Replace ember material annually. Improperly
placed embers interfere with proper burner operation.
• Embers CANNOT be placed directly over ports. Care
should be taken not to cover the lighting trail of ports
(from back to front).
• When placing Glowing Embers onto the burner care
should be taken so that the ports are not covered. Place
the dime-size ember pieces near the port holes in the
burner top. Failure to follow this procedure will likely cause
lighting and sooting problems.
Install Vermiculite
Vermiculite may be used for aesthetic enhancement, if
desired. Sprinkle the vermiculite on the interior oor of the
replace as shown in the gure below. Do not place ver-
miculite on burner. Care should be taken to avoid using
excessive amounts of vermiculite.
WARNING! Risk of Explosion or Delayed Ignition! DO
NOT place vermiculite on burner.
Place Vermiculite