HEATSTRIP Classic THH1500AUL Instruction Manual

R A D I A N T O U T D O O R H E A T E R S
OPERATION, INSTALLATION AND MAINTENANCE MANUAL
HEATSTRIP® Indoor
The heater that is a design f e a ture!
R A D I A N T O U T D O O R H E A T E R S
HEATSTRIP® Class ic ( T H H -AUL)
The heater that is a design f e a ture!
OPERATION, INSTALLATION AND MAINTENANCE MANUAL

2
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electric shock, and injury to persons, including the following:
1 Read all instructions before installing or using this heater.
2 This heater is hot when in use . To avoid burns, do not let bare skin touch hot surfaces.
Keep combustible materials, such as furniture, pillows, bedding, papers, clothes,
etc. and curtains at least feet (0.9mm) from the front of the heater and keep them away
from sides and rear restrictions apply to location dedicated heaters only.)
3 Extreme caution is necessary when any heater is used by or near children or invalids
and whenever the heater is left operating and unattended.
4 Do not operate any heater after it malfunctions. Disconnect power at service panel and
have heater inspected by a reputable electrician before reusing .
5 To disconnect heater, turn controls to off, and turn off power to heater circuit at main
disconnect panel ( or operate internal disconnect switch if provided)
6 A heater has hot and arcing or sparking parts inside. Do not use it in areas where gaso-
line, paint, or flammable vapours or liquids are used or stored.
7 Use this heater only as described in this Manual. Any other use not recommended by
the manufacturer may cause fire, electric shock, or injury to persons .
“SAVE THESE INSTRUCTIONS”

INSTALLATION 3
1 This equipment shall be installed only by qualified personal who are familiar with the
construction and operation of the apparatus and hazard involved.
2 The heater is fitted with an electrical connection box and should be connected as a fixed
installation by a licensed electrical professional in accordance with the relevant electrical
code.
3 Within USA, electrical installation shall be made in accordance with the National Electri-
cal code.
4 Within Canada, electrical installation shall be made according to the provisions of section
62 of the Canadian electrical code Part 1.
5 This appliance must be grounded.
6 An over current protection device (or circuit breaker) is required for proper installation.
The rating of the device should be 150% of the rating of the product.
7 The THX series heaters are designed for domestic/ commercial heating applications
within indoor or outdoor area and should not be used for any other purpose. Any other use
not recommended by the manufacturer may cause fire, electric shock or injury to persons.
8 Before commencing installation make sure the electrical supply voltage is the same as
that shown on the rating plate of the heater.
9 The heater must be mounted at least 6 feet(1.8m) above ground level when installed in
USA and 8 feet (2.4) above ground level when installed in Canada . For other clearances
please refer to the diagram included in these instructions.
10 Do not use heater in areas where gasoline, paint or flammable liquids are used or
stored.
11 The heater is not intended for use in bathrooms, laundry areas or similar indoor areas.
Never locate heater where it may fall into a bathtub, pool, spa or other water container.
12 Do not operate the heater after the heater malfunctions, or has been dropped or dam-
aged in any manner. Return heater to authorised service facility for examination or me-
chanical adjustment or repair.
13 There are no user serviceable parts inside the heater any servicing other then cleaning
of the heater should be performed by an authorised service representative
CAUTION:
High temperature risk of fire, keep electrical cords, drapery, furnishings and other
Combustibles At least feet (0.9m) from front of heater and away from side and rear of
heater.

R A D I A N T O U T D O O R H E A T E R S
4
Product Overview Rev D JUN14
Why choose Heatstrip
®
electric radiant heaters for your outdoor or hard-to-heat indoor area?
As there is typically constant air movement in an outdoor or open indoor area, many conventional patio heaters rely on
convection heating which works by heating the surrounding air. This can be quite impractical for these areas, as this
heated air can easily blow away with natural air movement. Radiant style heaters transfer heat directly to objects through
infra-red waves.
Whilst convection heaters heat the air in between objects, radiant heaters heat the surface of the objects themselves.
HEATSTRIP
®
electric radiant heaters are more effective within an outdoor or uninsulated indoor area because they
provide targeted warmth directly to the people and objects in their path.
Discrete, stylish heating for undercover outdoor and indoor open areas
Using the radiant heating principle, HEATSTRIP
®
can provide effective and energy efficient comfort heating for undercover
outdoor and indoor open areas. HEATSTRIP
®
has successfully enabled many entertainment venues such as restaurants,
pubs and clubs to utilise their outdoor dining areas day and night, through all seasons. Within your workplace or business,
HEATSTRIP
®
can provide comfort heating for designated outdoor smoking and leisure areas, as well as for workstation
spot heating in factories, warehouses and showrooms. Within your home, HEATSTRIP
®
can provide comfort heating for
undercover alfresco dining and BBQ area, patios, verandas, courtyards and balconies.
Subtle, minimalist design
The stylish, slimline black face of the HEATSTRIP
®
does not emit light or glow when in use, blending elegantly into your
décor. Ceiling, wall and umbrella mounting options ensure that your valuable floor and table space is not wasted.
APPLICATION THH
Indoor insulated areas, classrooms, offices, bathrooms, wet areas, drying rooms √
Outdoor under cover, café, veranda, patio, balcony ceiling height 3m or less √
Indoor open area, warehouse, factory, production areas, sports facilities √
Indoor spot heating, above tables, assembly areas √
This is a general guide only, please refer to the Product Manual for each product, for more information.
HEATSTRIP
®
Classic (THH models) is a premium high temperature heater and is primarily used for outdoor rooms where
there is 1,2 , or 4 enclosed sides, with an ideal mounting height of 82” to 105” (2.1 m to 2.7m.)

R A D I A N T O U T D O O R H E A T E R S
5
Efficient, cost effective electric heating
The innovative design of the HEATSTRIP
®
enables comfortable and even heat dispersion from the surface with minimal
operating costs.
Design flexibility
Three HEATSTRIP
®
models are available, ensuring the heating requirements of any undercover outdoor or open
indoor area is possible. Brackets for direct ceiling or wall/ceiling angled mounting are supplied as standard.
Optional HEATSTRIP
®
accessories include beam or fixed umbrella mount brackets, extension mount brackets,
chain suspension brackets, twin mount brackets and flush mounting enclosures.
Minimal maintenance
The HEATSTRIP
®
incorporates no internal moving parts ensuring quiet and virtually maintenance free operation.
Australian made
Designed, engineered and assembled in Australia the HEATSTRIP
®
,is fully backed by a 12 month warranty.
Stylish design— The Heater that is a Design Feature!
The attractive HEATSTRIP
®
comes with a standard black face and anodised alloy rear casing.
Easy to use
The standard HEATSTRIP
®
is controller by a simple on/off operation, either when plugged directly into a power point, or
hard-wired via a wall mounted on/off switch. The unit takes approximately 15 minutes to heat up to maximum temperature
and approximately 0 minutes to cool down, depending upon the ambient temperature. Please don’t forget to turn it off.

R A D I A N T O U T D O O R H E A T E R S
6
Specifications - AUL
MODEL POWER
(WATTS)
CURRENT
(AMPS)
DIMENSIONS
(inches)
WEIGHT
(lbs)
THH1500AUL 1500 12.2 6” x 6.5” x 2” 11
THH2400AUM 2400 11. 5 .5” x 6.5” x 2” 17.5
THH 200AUM 200 15 70” x 6.5” x 2” 22
VOLTAGE
(VOLTS)
120
208
208
THH2400AUL 2400 240 10 5 .5” x 6.5” x 2” 17.5
THH 200AUL 200 240 1 70” x 6.5” x 2” 22
NAME
HEATSTRIP MINI
HEATSTRIP REGULAR
HEATSTRIP LARGE
HEATSTRIP CAFE
HEATSTRIP RESTAURANT
MODEL
HEATER TYPE High intensity electric radiant overhead heater with high surface area
profiled alloy
OUTPUT Refer to model code chart above
POWER 120, 208 or 240 Volts Nominal at 50—60 Hertz, Single Phase
CONNECTION Gangbox
APPROVALS CSA/UL E 21448
MOUNTING HEIGHT MINIMUM
RECOMMENDED
MAXIMUM
82” (2.1 m)
90” to 105” (2. m to 2.7 m)
117” ( .0 m) For higher ceiling heights, units can be
lowered using optional bracket kits or refer to the
Heatstrip Max range
PROTECTION RATING IP55 Protection from water ingress from all directions
COUNTRY OF MANUFACTURE Australia
MOUNTING OPTIONS Suitable for ceiling, wall, beam, fixed umbrella and recess mounting. Also
available for extension mount using rigid fixing poles and chain mount
bracket.
6" (924mm)
2" (42mm)
5.5" (164mm)
70" (1774mm)
THH1800A
THH2400A
THH 200A
6.5" (172mm)
6.5" (172mm)
6.5" (172mm)
2" (42mm)
2" (42mm)
THH1500A

R A D I A N T O U T D O O R H E A T E R S
7
BAR
BAR STOOLS
DINING TABLE
LOUNGE
BBQ
2 x THH24006 x THH2400
Spot heating principle
In most outdoor or difficult-to-heat indoor applications, there are 2 options when looking at the size and quantity
of the heater required. Option 1 is to comfort heat the entire area based on the total dimensions of the space,
regarding of whether the entire area is being fully occupied. Option 2 is to spot heat the high use areas, such as
over outdoor tables, BBQ’s, lounges, assembly lines or indoor workstation.
Often it is more practical and efficient to spot heat these areas. Spot heating will help to reduce the initial capital
cost, as well as the running costs. Spot heating will allow the area to be “zoned”, meaning heating only the areas
that are being used, such as tables in a restaurant or outdoor alfresco area.
The top table shows a comparison between spot heating over a table, or heating an entire area.
The bottom table shows the flexibility of using HEATSTRIP
®
to provide a comfortable environment, even when
the layout of the area is very unusual.
6 x HEATSTRIP REGULAR 2 x HEATSTRIP REGULAR

R A D I A N T O U T D O O R H E A T E R S
8
77°F
70°F
1" STANDING HEIGHT
45" SITTING HEIGHT
94" MAXIMUM HEIGHT
54°
7 °F
58"
54"
78"
110"
Radiant footprint
HEATSTRIP
®
electric heater produce radiant heat,
which heats objects rather than the air. Therefore, it is
imperative that objects to be heated (ie. People), are
within the direct radiant footprint of the heater.
The diagram to the left shows the radiant footprint of
HEATSTRIP
®
, and is an approximate guide based on
a fully enclosed, outdoor environment.
This diagram shows that the maximum heat output is
found directly under the heater, and the temperature
decreases as you move away from the heater.
It highlights the importance of maintaining
recommended mounting heights, and positioning the
heater directly above the area to be heated, if possible.
Also, the temperature (ie. surface temperature) is the
same for all models, regardless of the wattage.
However, the size increases and the length of the unit
increases, the radiant footprint will be larger.
The below diagrams show the approximate heating
area for each model, based on both an indoor and
outdoor enclosed environment.
1 7"
82"
70"
LARGE
102"
82"
55"
REGULAR
62"
82"
5"
MINI
HEATED AREA
INDOOR SPOT HEATING
105"
82"
70"
78"
82"
55"
50"
82"
5"
HEATED AREA
OUTDOOR ENCLOSED AREA
MINI
REGULAR
LARGE

R A D I A N T O U T D O O R H E A T E R S
9
Selection guide
Prior to selecting the exact model and quantity required for your application, please ensure the correct model heater is
being used.
HEATSTRIP
®
Classic (THH models) is a premium high temperature heater and is primarily used for outdoor rooms where
there is 1,2 or 4 enclosed sides, with an ideal mounting height of 82” to 105” (2.1 m to 2.7m.) Ideal for hard to heat in-
door applications or moist environments where an IP55 rating is required.
General recommendations for HEATSTRIP
®
Classic:
• Ideal mounting height: 82” to 105” (2.1 m to 2.7m.) Maximum is 117” ( m) in a protected outdoor environment.
• Ideal mounting location: ceiling mounted, directly above area to be heated (eg. above a table)
• Based on the radiant footprint of the previous page, for a protected outdoor area, a minimum of 500W/m2 is re-
quired. For indoor spot heating, a minimum heating capacity of 400W/m2 is recommended.
The below table outlines the coverage of each HEATSTRIP
®
Classic model (in m2), based on different scenarios.
For example, for all outdoor area that is protected from prevailing winds by walls, café blinds etc, Model Heatstrip Mini will
cover 2 ft2 and Model Heatstrip Regular will cover 52 ft2.
MODEL INDOOR PROTECTED (ft
2
) OUTDOOR ENCLOSED (ft
2
) OUTDOOR EXPOSED (ft
2
)
HEATSTRIP MINI
40
( .75 m2)
2
( m2)
26
(2.5 m2)
HEATSTRIP REGULAR
65
(6 m2)
52
(4.8 m2)
4
(4 m2)
HEATSTRIP LARGE
86
(8 m2)
69
(6.4 m2)
57
(5. m2)

R A D I A N T O U T D O O R H E A T E R S
10
Table layout
For the majority of outdoor applications, the most effective method is to spot heat a table or similar area. The below dia-
grams provides an easy selection guide for the approximate model and quantity of heaters required to heat common resi-
dential table settings.
Selections are based on HEATSTRIP
®
Classic being mounted at 94” (2.4m) from the floor and an undercover fully en-
closed outdoor area.
HEATSTRIP MINI HEATSTRIP REGULAR HEATSTRIP LARGE
2 x HEATSTRIP REGULAR
2 x HEATSTRIP LARGE
2 x HEATSTRIP MINI
4 x HEATSTRIP MINI
HEATSTRIP REGULAR
HEATSTRIP LARGE

R A D I A N T O U T D O O R H E A T E R S
11
CEILING
Installation Requirements
The ideal mounting position for the HEATSTRIP
®.
Classic is on the ceiling, directly above the area to be heated. If this is
not possible, HEATSTRIP
®.
can be mounted on a wall and angled downwards. In this situation, ensure the mounting
height is in the range of 82” to 105” (2.1 m to 2.7m) and the table is within 98” (2.5m) of the wall.
For mounting heights more than 117” ( m,) we recommend the use of the optional accessories to reduce the height of the
heater to 82” to 105” (2.1 m to 2.7m.) This will increase the effectiveness of your HEATSTRIP
®.
Refer to the Mounting
Accesory section for more information.
Electrical connections/GPO’s should not be located at the back of the heater. They should be located outside the physical
footprint of the units to minimize heat build-up behind the units.
If the heater is to be mounted on an incline (eg. Vaulted ceiling), ensure the electrical connection is located at the lowest
point of the heater.
The heating surface must never be directed toward the ceiling
CEILING
CEILING
INCORRECT
INSTALLATION
CORRECT
INSTALLATION
CEILING
CEILING

R A D I A N T O U T D O O R H E A T E R S
12
40" Min.
82" Min.
96" Min.
ANGLED CEILING INSTALLATION
2 1/2" Min.
2 1/2" Min.
CEILING
FLOOR
Wall
SURFACE BELOW HEATER
LIGHT, FAN OR SPRINKLER MUST
NOT BE BELOW THE HEATER
CEILING
FLOOR
Wall
SURFACE BELOW HEATER
LIGHT, FAN OR SPRINKLER MUST
NOT BE BELOW THE HEATER
40" Min.
2 1/2" Min.
12" Min.
40" Min.
82" Min.
96" Min.
40" Min.
82" Min.
6" Min.
6" Min.
CEILING
LIGHT, FAN OR SPRINKLER MUST
NOT BE BELOW THE HEATER
FLOOR
Wall
SURFACE BELOW HEATER
Installation location —the below diagrams confirm the minimum recommended clearances.
Angled Ceiling Installation
Ceiling Installation
Angled Wall Installation

R A D I A N T O U T D O O R H E A T E R S
1
STANDARD
BRACKET
CEILING
TWIN MOUNT
BRACKET
EXTENSION
MOUNT
BRACKET
SUSPENSION
MOUNT
BRACKET
FLUSH
MOUNT
ENCLOSURE
Mounting options
The installation of HEATSTRIP
®
Classic is simple and easy with the standard mounting brackets supplied. For other more
challenging locations there are a range of mounting options available - refer to below diagrams.
The HEATSTRIP
®
Classic can be mounted directly to the ceiling, angled downwards on a wall, fitted flush with the ceiling;
suspended on chains or poles; attached to beams or poles; mounted end-to-end, or 2 units together. Refer to the following
pages for more detailed information on each mounting option.
STANDARD MOUNTING BRACKETS
INCLUDED IN BOX
FLUSH MOUNT ENCLOSURE
END TO END MOUNTING BRACKET
TWIN MOUNT BRACKET
SUSPENSION MOUNT BRACKET
EXTENSION MOUNT KIT WITH POLES

R A D I A N T O U T D O O R H E A T E R S
14
STANDARD MOUNTING BRACKET
B
Standard mounting brackets
The HEATSTRIP
®
Classic comes with a pair of standard mounting brackets. These adjustable brackets allow direct ceiling
or wall mount, and come with preset angle options of parallel, 22.5° and 45°.
The brackets need to be mounted onto a secure frame or wall with a minimum distance between the two brackets. The
minimum distance (“B”) for each model is listed in the table below.
When completing the installation, ensure all screws are tight and unit is secure.
There are 4 silicon strips included in the mounting bracket kit. Use these strips to bend around the end of the bracket and
slide into the rear casing.
PART No PACKAGED
DIMENSIONS (inches)
WEIGHT
(lbs)
ZBRAK-10 6” x 6” x 2”
(150 x 150 x 50mm)
1
(0.5kg)
MATERIALS
16 SS
Standard Mounting Bracket
MODEL “B”
MINIMUM DISTANCE (inches)
MINI 21” (550mm)
REGULAR 40” (10 0mm)
LARGE 58” (1470mm)
1.6" 4"
2"
6.5"

R A D I A N T O U T D O O R H E A T E R S
15
Flush Mount Enclosure
The Flush Mount Enclosure is an ideal way to neatly install the HEATSTRIP
®
into a ceiling. They are available for
all HEATSTRIP
®
Classic models, and are supplied as a one-piece unit for mounting of heaters. Flush mounting
can be used with plaster or wood lined ceiling materials.
An ideal mounting height is 90” - 105” (2.5m-2.7m), with a maximum ceiling height of 117” ( .0m) in an outdoor en-
closed environment. Maximum mounting heights should be strictly followed, otherwise the performance of the units
may be reduced.
The facia of the enclosure is manufactured from 16 Stainless Steel and the rear casing is black zinc coated steel.
Please refer to the Installation Manual for more detailed installation information.
SUITABLE FOR
MODELS
PART No HOLE CUTOUT
DIMENSIONS (inches)
OVERALL
DIMENSIONS
(inches)
WEIGHT
(lbs)
MINI THHAC-009 8.5” x 9”
(980 x 2 0mm)
40. ” x 11” x 4.9”
10 0 x 280 x 125
12
(5.5kg)
REGULAR THHAC-011 55.5” x 9”
(1420 x 2 0mm)
57.5” x 11” x 4.9”
(1470 x 280 x 125mm)
18
(8kg)
LARGE THHAC-012 72.5” x 9”
(18 0 x 2 0mm)
7 .6” x 11” x 4.9”
(1880 x 280 x 125mm)
22
(10kg)

R A D I A N T O U T D O O R H E A T E R S
16
Twin mounting bracket
PART No PACKAGED
DIMENSIONS
(inches)
WEIGHT
(lbs)
THHAC-016 12” x 2’ x 2”
( 00 x 50 x 50mm)
0.7 lbs
(0.25kg)
MATERIALS
16 SS
The optional Twin Mount bracket allows for two (2) units of HEATSTRIP
Classic to be mounted side-by-side, either in parallel or angled as per the
diagram on the right. This is ideal for applications when a wider heat
coverage is required, or when there is mounting restrictions/limitations
(such as running between 2 rows of tables etc.)
The Twin Mount bracket can also be used with the Extension Mount
bracket and Pole Kit, to lower the units from a high ceiling.

R A D I A N T O U T D O O R H E A T E R S
17
End to end mounting bracket
PART No PACKAGAED
DIMENSIONS (inches)
WEIGHT
(lbs)
THHAC-017 12” x 6” x 2”
( 00 x 150 x 50mm)
1lb
(0.5kg)
MATERIALS
16 SS
The end to end bracket allows multiple units to be joined in a straight line for maximum heat performance
and aesthetic appeal. This is ideal for applications such as long rows of tables and assembly lines, where a
constant heat coverage is required.
The bracket allows for a 2” (50mm) gap between units and an opening for the power connection. As per the
diagram below, units should be mounted with the power leads apart.
2"

R A D I A N T O U T D O O R H E A T E R S
18
The Suspension Mount bracket provides a cheap, easy and effective option for lowering the HEATSTRIP
®
Classic from high ceilings. If the ceiling height is more than 118” ( .0m) is an enclosed outdoor environment,
or 105” (2.7m) in an exposed site, it is recommended to lower the heaters to an ideal mounting height of 90”
to 105” (2. m to 2.7 m).
The bracket is designed to be used with chains or wires. There can be multiple chain/wire arrangement op-
tions, as per the below diagram.
PART No PACKAGED
DIMENSIONS (inches)
WEIGHT (lbs)
THHAC-002 28” x 6” x 2”
(700 x 150 x 50mm)
2.2 lbs
(1 kg)
MATERIALS
16 SS
THHAC-00 48” x 150” x 2”
1200 x 120 x 50
5 lbs
(2 kg)
16 SS
SUITABLE FOR
MODELS
MINI
REGULAR
& LARGE
Suspension mount bracket

R A D I A N T O U T D O O R H E A T E R S
19
Extension Mount Bracket
PART No PACKAGED
DIMENSIONS (mm)
WEIGHT
(lbs)
THHAC-007 6” x 12” x 2”
(900 x 150 x 50mm)
6 lbs
(2.5 kgs)
MATERIALS
16 SS
THHAC-004 12” x 12” x 2”
(150 x 150 x 50mm)
2 lbs
(1 kg)
16 SS
THHAC-006 24” x 12” x 2”
(600 x 150 x 50mm)
5 lbs
(2 kgs)
16 SS
THHAC-005 12” x 12” x 2”
( 00 x 150 x 50mm)
5 lbs
(2 kgs)
16 SS
THHAC-008 48” x 12” x 2”
(1200 x 150 x 50mm)
7 lbs
( kgs)
16 SS
NOTES
Brackets only
(for use with 25x25x1mm tube)
Kit includes 2 x 12” ( 00mm) extension pole,
screws and brackets
Kit includes 2 x 24” (600mm) extension pole,
screws and brackets
Kit includes 2 x 6” (900mm) extension pole,
screws and brackets
Kit includes 2 x 48” (1200mm) extension pole,
screws and brackets
The Extension Mount bracket allows HEATSTRIP
®
Classic units to be lowered from high ceilings, using rigid
connections. The brackets are for use with 1” x 1” (25mm x 25mm x 1mm tube) (SHS), and can be supplied as
brackets only for customising the length of the drop on site; or supplied as a complete kit with brackets, pre-cut
poles and connections. The standard length options as part of the kit are 12” ( 00mm), 24” (600mm),
6” (900mm) and 48” (1200mm).
The kits include all brackets, poles and screws necessary for connection to the heaters, however it does not
include screws for attachment to the ceiling.
*screws to ceiling are not included
12" ( 00mm)
24" (600mm)
6" (900mm)
48" (1200mm)
48.5" (12 mm)
6.7" (9 mm)
24.9" (6 mm)
1 .1" ( mm)

R A D I A N T O U T D O O R H E A T E R S
20
Safety
HEATSTRIP
®
Classic has an IP rating of 55. This means it is safe for water ingress from all directions. The HEATSTRIP
®
can be safely hosed down.
HEATSTRIP
®
has undergone extensive testing both in laboratory conditions; in Thermofilm’s manufacturing facility in
Melbourne and field trials in Australia and overseas. It has been this testing that gives the purchaser the confidence of a
high quality product.
Independent laboratory testing has confirmed Thermofilm’s full compliance with Australian and other International
Standards. This includes CE, AS/ANZ, UL/CSE.
The heater comes in 1500W, 2400W and 200W versions. In all events the fixed wiring must be installed by a licensed
electrician in accordance with the relevant wiring regulations.
HEATSTRIP
®
is Class 1 equipment and must be earthed.
In operation, this heater is VERY HOT— do not touch any part of the heater while it is turned on. Do not touch any part
until 0 minutes after it is turned off.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or intellectual
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the
appliance.
Do not allow any cables, furnishings, flammable materials or other items come in contact with any surface of the heater.
If installed in wet areas, the heater switches or controls must be located so that they cannot be touched by persons in the
bath or shower.
The heater needs to be installed as per the installation instructions paying special attention to the minimum clearances.
The heater needs to be mounted on a rigid bracket or fixing.
The heater must not be mounted immediately below or in front of a socket outlet.
In case of a heater fault or damaged supply lead, the appliance should be returned to the point of purchase for return to
Thermofilm for repair.
Maintenance
The HEATSTRIP
®
is made from durable materials, however regular care and maintenance of your heater will help prolong
the life of the heater.
It is recommended that you hose down the heater and with a soft cloth gently wipe the surfaces of the heater with a mild
detergent to remove the built up contaminants from the environment. Then rinse all detergent off the heater.
All chemicals in the atmosphere including cigarette smoke, pollution etc. will tarnish the surface of the heater. In this case,
additional cleaning and maintenance may be required. The cleaning process at least every three months will reduce the
amount of build up and keep it looking as best it can. If the heater is in a corrosive environment eg. salt spray, we
recommend that you clean your heater with a light spray of fresh water every week. After cleaning, turn the heater on for
20 minutes to dry any water residue and prevent water staining.
Before cleaning or inspection activity, the heater must be switched off and cooled down completely.
Do not use any abrasive materials or products to clean the heater, this includes solvents, citrus based cleaners or other
harsh cleaning products.
When handling the heater, ensure that your hands are clean or that you use clean gloves as grease or dirt can mark the
surface of the heater.
Do not use high pressure water to clean heaters, light water spray only.