HEATSTRIP THH 1500 Instruction manual

Models Watts Dimensions Ratings
THH 1500, THH 1500SS 1550 850 x 170 x 40mm 230V 50Hz a.c
THH 2400, THH 2400SS 2500 1330 x 170 x 40mm 230V 50Hz a.c
THH 3200, THH 3200SS 3350 1770 x 170 x 40mm 230V 50Hz a.c
Note: THH series HEATSTRIPS have an IPX5 rating for protection against water ingress. Prior to
installing and operating the heater, read these instructions carefully and retain for future reference.
Preparation
The THH Series HEATSTRIPS are high intensity Radiant Strip Heaters designed for Domestic /1.
Commercial heating applications within indoor or outdoor undercover areas, and should not be
used for any other purpose.
Before commencing installation, make sure the electrical supply voltage is the same as that2.
shown on the rating plate of the heater.
The heater is fitted with a length of flexible cable for electrical connection. The heater should3.
be connected as a fixed installation by a licensed electrical person, according to the relevant
electrical standards.
All pole disconnection from the supply mains must be provided in fixed wiring in accordance with4.
the wiring rules.
This appliance must be earthed.5.
The heater is required to be fitted with an “ON/OFF isolation switch and can also be controlled6.
via thermostat, timer or dimmer type control. A wall switch should be installed on fixed wire
installations. Optional connection to a R.C.D is recommended.
If the heater or supply lead is damaged, the appliance must be returned to the distributor /7.
manufacturer for repair.
Installation Location
For both wall and ceiling mounting, the lowest part of the heater must be located a minimum of*
2100mm above floor level.
The heater must not be closer than 300mm to adjacent walls, with a minimum of 60mm*
between back of heater and any surface.
Allow 1000mm from the bottom of the heater to any surface below.*
Do not allow thermal insulation, cables, flammable materials or any other items to come into*
contact with any surface of the heater; purpose design brackets excluded.
The heater must not be located immediately below a socket outlet.*
If installed in wet areas, the heater must be installed so that switches and other controls cannot*
be touched by persons in the bath or shower.
Electric Radiant Outdoor Heater
Installation, Operation & Maintenance Manual
EUROPE / UNITED KINGDOM - ENGLISH
ENGLISH 1

Self Tapping Screw
M5 Machine
Thread Screw
Dim “A”
M5 Hex Nut
Mounting Instructions
Using the centre distances shown in DIM “A”, mount the brackets to the ceiling or wall.*
Ensure fixing method will adequately support weight of heater.*
Then, fix brackets to heater using the nuts provided on the studs at rear of heater.*
Ensure screw fixing two halves of bracket is fully tightened.*
Use the two small self tapping screws to lock the two halves of the bracket at the desired angle.*
The heating surface must never be directed toward the ceiling.*
The power cable must be at the lower end of the heater if the heater is installed at an angle.*
Operation Instructions
[To be kept by the user of this appliance]
The heater is required to be fitted with an “ON/OFF” isolation switch and can also be controlled via
thermostat, timer or dimmer type control. Once the unit is turned On via a switch or other control
device, it will take approximately 10 minutes to warm up to normal operating temperature. Make
sure the unit is turned OFF after use.
Note: THH series HEATSTRIPS have an IPX5 rating for protection against water ingress.
CAUTION
The front panel of the heater can reach temperatures of up to 380°c.*
Do not touch any part of the heater while in operation or for 30 minutes after turning off.*
This appliance is not intended for use by young children or infirm persons.*
Caution must be exercised when operating this appliance.*
Do not allow any cables, furnishings, flammable materials or other items to come into contact*
with any surface of the heater.
The heater must have a minimum 300mm clearance to adjacent walls and minimum 60mm*
clearance from the back of the heater to any mounted surface.
Do not operate heater unless there is a clearance of 1000mm or more from bottom of the heater*
to any surface below.
The heater should be connected as a fixed installation by a licensed electrical person, according*
to the relevant electrical standards.
All pole disconnection from the supply mains must be provided in fixed wiring in accordance with*
the wiring rules.
Model DIM “A”
THH 1500 300mm
THH 2400 600mm
THH 3200 900mm
ENGLISH 2

Distributed by:
GRAND HALL EUROPE
Hanzepoort 31
7575 DB Oldenzaal, The Netherlands
Tel [phone]
Fax [phone]
[email protected]
www.grandhall.eu
The heater must not be located immediately below a socket outlet.*
If installed in wet areas, the heater must be installed so that switches and other controls cannot*
be touched by persons in the bath or shower.
If the heater or supply lead is damaged, the appliance must be returned to the distributor /*
manufacturer for repair.
In case of heater fault, the appliance must be returned to the distributor / manufacturer for repair.*
Prior to installation remove all packaging including the card board spacers at each end of radiator*
panel and all plastic film on stainless steel models.
Cleaning & General Maintenance
It is important that THH HEATSTRIP units installed in outdoor locations are regularly cleaned to
ensure a long and efficient operating life. In coastal locations in particular, salt in the air can cause
rusting and staining of metal. Even in city locations, pollution in the air can also contaminate
surfaces and will affect the ability of the coatings and material of your THH HEATSTRIP to protect
from rust and stains. This applies to both the painted and stainlesss steel models. As the THH
HEATSTRIP has a protection rating for water ingress of IPX-5, they can be safely washed and
cleaned with water. The heater can be lightly sprayed with a hose, but the preferred method of
cleaning is to rinse the heaters using a soft cloth with warm water and a mild detergent. Ensure any
soap residue is rinsed off after cleaning.
CAUTION:
Before any cleaning activity, the heater must be switched off and cooled down completely. (The*
heaters can be turned on briefly after washing to dry them off quickly.)
DO NOT use a high pressure hose or high pressure water equipment to clean the heaters.*
As a guide, THH HEATSTRIP units should be cleaned whenever you are cleaning the outdoor*
furniture in the same area. In coastal areas, an additional rinsing on a fortnightly basis with a
light spray from a hose will provide extra protection.