Hioki 7016 User manual

OPERATION GUIDE
SIGNAL SOURCE
7016

i
Contents
Contents
Introduction ............................................................... 1
Chapter 1 Source Function 3
1.1 Basic Sourcing Procedure........................... 4
1.2 Constant-Voltage Source (DCCV)............... 6
1.3 Constant-Current Source (DCCC)............... 8
1.4 Pulse Source (PULSE).............................. 10
1.5 Using Memory Function
(SCAN and RAMP).................................... 12
1.5.1 Using the SCAN Function .............. 12
1.5.2 Using the RAMP Function.............. 17
Chapter 2 Measurement Function 21
2.1 Basic Measurement Procedure
(Common Procedure)................................ 21
2.2 Measuring Voltage .................................... 23
2.3 Measuring Current..................................... 25
2.4 Measuring Frequency................................ 27
2.5 Measuring the Resistance......................... 28
2.5.1 Continuity Test ............................... 30
2.6 Diode Test ................................................. 31
2.7 Measuring Temperature ............................ 32

Contents
ii
Chapter 3 Special Measurement
Functions 33
3.1 Recording Function ................................... 34
3.2 Data Hold / Refresh Hold Function ........... 36
3.3 Relative (relative display) Function ........... 38
3.4 1-ms Peak Hold Function.......................... 39
3.5 Dual Display Function ............................... 41

1
Introduction
This manual describes the basic operation of
HIOKI 7016 SIGNAL SOURCE.
❖Details→Instruction manual for the 7016
Introduction
Symbols
❖Indicates the reference.
Indicates quick references for operation.

Introduction
2

3
Source Function Chapter 1
Important!
• The yellow labels around the outer circum-
ference of the function selector indicate
signal source/generation
• functions.
• The [SHIFT] button must first be pressed
to enable the source-related button func-
tions.

1.1 Basic Sourcing Procedure
4
1.1 Basic Sourcing Procedure
1. Set the slide switch to the
[M/S] position.
2.
Set the function
selector to the follow-
ing position.
(ex. Sourcing constant-
current)
Sourcing constant-voltage [CV]
Sourcing constant-current [CC]
Sourcing pulse [PULSE]
Using memory function Voltage source: [CV]
Current source: [CC]

5
1.1 Basic Sourcing Procedure
4. Press the [MODE] button as necessary to select
the source mode or the parameter on the second-
ary display.
5. Making the settings with the [W], [X], [S], or [T]
button.
7. Press the [OUTPUT] button again to disable out-
put. Verify that is no longer displayed.
3.
Press the [SHIFT] button
and confirm that is
displayed on the LCD. (Ex. Voltage Source)
The source-related button functions are now enabled.
6.
Press the [OUTPUT] but-
ton and output the setting
value. Verify that is
displayed on the LCD. (Ex. Voltage Source)

1.2 Constant-Voltage Source (DCCV)
6
This mode outputs a constant current at the set
value regardless of load.
Procedure
1.2 Constant-Voltage Source (DCCV)
1. Set the slide switch. [M/S]
2. Set the function selector. [CV]
3. Press the [SHIFT] button. Confirm that
is displayed.
4.
Press the [ MODE ] button as nec-
essary to select the source mode
on the secondary display.
Source Mode
• Constant-voltage
source 1.5 V range
• Constant-voltage
source 15 V range
• Constant-voltage
SCAN source 1.5 V
range
• Constant-voltage
SCAN source 15 V
range
• Constant-voltage
RAMP source 1.5
V range
• Constant-voltage
RAMP source 15 V
range