Hirose EnerBee DF60 Series User manual

1. Scope
This document specifies the steps to insert or remove the DF60 series.
It contains general guidelines and precautions for the safe use of the product.
The use of the product in a way not as specified in the document could result in unexpected
troubles such as damage to connectors.
Please make sure to thoroughly read and understand the document prior to the use of the
product.
2. Connectors
Part No.
Description
DF60#-*P-10.16DS(A)
Header
DF60#-*EP-10.16C
In-line Plug
DF60#-*S-10.16C
Socket
DF60#-*S-10.16C-CV
Covercase
DF60#-****SC(F)A
Crimp contact for socket
DF60-****PC(F)A
Crimp contact for In-line plug
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
CHECKED
DATE
1
6
DIS-H-00019386
SN.MIWA
TT.OHSAKO
20231101
名称TITLE
DF60 Series Mating/Unmating Operation Instruction Manual
APPROVED
SJ.OKAMURA
20210728
CHECKED
SZ.ONO
20210728
DESIGNED
TS.MIYAKI
20210728
WRITTEN
TS.MIYAKI
20210728
技術指定書TECHNICAL SPECIFICATION
ETAD-H0654-00
1
1/ 6
FORM HC0011-9-1
HIROSE ELECTRIC CO.,LTD.
△
Fig. 1. DF60 connector
△
DF60-3S-10.16C
+ DF60-####SC(F)A
DF60FS-3S-10.16C
+ DF60FS-3S-10.16C-CV
+ DF60S-####SC(F)A
1
DF60-3P-10.16DSA
DF60-3P-10.16DS
DF60-3EP-10.16C
+ DF60-####PC(F)A

HIROSE ELECTRIC CO.,LTD.
ETAD-H0654-00
1
2 / 6
FORM HC0011-9-2
△
3. Operation procedure
3-1. Insertion
3-1-a. Positioning for insertion:
：Adjust the position for insertion according to the locks of the socket or In-line plug.
3-1-b. Insertion:
Insert the socket till it clicks while retaining the adjusted position.
Then, it is not needed to handle the lock portion
(If it is inserted the socket by pushing the lock portion, it does not hear click sound.)
Fig. 2. Positioning for insertion
Fig. 3. Insertion
Inserting direction
Push in the center
Straight type
Right angle type
Inserting direction
1
1

HIROSE ELECTRIC CO.,LTD.
ETAD-H0654-00
1
3 / 6
FORM HC0011-9-2
△
Attention 1. To avoid degraded quality, do not tilt the socket for insertion as shown in the
figure below.
Attention 2. Avoid insert socket by bundling the cable or
applying stress to the socket like below picture shown.
Fig. 4. Forbidden insertion (1)
Fig. 5. Forbidden insertion (2)

HIROSE ELECTRIC CO.,LTD.
ETAD-H0654-00
1
4 / 6
FORM HC0011-9-2
△
3-1-c. Check fitting:
Make sure the socket has been firmly fit with the header or In-line plug.
(Check that the socket lock has been caught at the header lock or In-line plug lock
by slightly pulling a cable by hand.)
To remove the socket, refer to 3-2. Socket removal.
3-2. Socket removal
3-2-a. Removal:
For straight type
While grasping the cable, use your entire finger to firmly release the lock and remove it.
Attention. If you remove the lock while it is caught, you will not be able to remove
it properly.
Fig. 6. Mating state
-2
Straight type
Right angle type
Gently grab the cable
Push the lock
Fig. 7. Socket removal
1
1

HIROSE ELECTRIC CO.,LTD.
ETAD-H0654-00
1
5 / 6
FORM HC0011-9-2
△
For right angle type
While grasping the side of the crimp socket or the cable, make sure to release the lock with
your entire finger and remove it.
Attention. If you remove the lock while it is caught, you will not be able to remove
it properly.
Attention. When grasping the cable, do not route it in a way that puts stress on the base.
4. Precautions
・Do not insert or remove the socket while electrifying.
・Do not pull the lock as shown below. The lock may be damaged.
Fig. 8. Prohibited uses (Unmating state)
Grab the sides
Gently grab the cable
Push the lock

HIROSE ELECTRIC CO.,LTD.
ETAD-H0654-00
1
6 / 6
FORM HC0011-9-2
△
・Excessive external force applied to connectors could cause fault or damage.
Please be careful not to route the cable in a way that puts a load on the base of the cable,
as shown in the diagram below.
Fig. 9. Prohibited uses (Mating state)
Do not bent from
the root
1