Ohlins DU 569 User manual

Shock absorber for Ducati Panigale V2/959/899
DU 569
Mounting Instructions
Note!1
Please note that there can be small differences
between your product and the images in
these instructions.
Note!1
Please note that during storage and transport,
especially at high ambient temperature, some
of the oil and grease used for assembly may
leak and stain the packaging. This will not
cause damage to the product, wipe off the
excessive oil or grease with a cloth.
Note!1
Before you install this product, check the kit
contents. If anything is missing, please contact
an Öhlins dealer.
Warning!⚠
Before you install this product, read the Öhlins
Owner’s manual. This product is an important
part of the vehicle and the vehicle stability.
Kit Contents
Description Part No Pcs
Shock absorber DU 569 1
C-spanner 00710-06 2
Sticker Memo notes 01180-01 1
Sticker set Öhlins 1
Owner’s manual 07242-07 1
Note!1
For Panigale 899: Shorten the shock absorber
5 mm by turning the end eye 5 turns in, before
mounting the shock.
For Panigale 959: Shorten the shock absorber
3 mm by turning the end eye 3 turns in, before
mounting the shock.

2
1
Put the motorcycle on a work stand so that the
rear wheel barely touches the ground.
2
Remove the original shock absorber.
MOUNTING INSTRUCTIONS
Warning!⚠
We strongly recommend to let an Öhlins dealer
install this product.
Warning!⚠
If you work with a lifted vehicle, make sure that it
is safely supported to prevent it from tipping over.
Note!1
When you work with this product, see the
vehicle service manual for vehicle specic
procedures and important data.
Note!1
Before you install this product clean the
vehicle.
3
Install the Öhlins shock absorber in the same
position as the original shock absorber.
Note!1
Lower the vehicle so that the suspension
is slightly compressed before you tighten
the screws.
4
Remove the plastic spring cover from the
original shock absorber and install it on the
Öhlins shock absorber.
5
Remove the seat.
6
Remove the bracket at the rear end of the tank.
7
Remove the cover around the ignition lock.
76
4

3
MOUNTING INSTRUCTIONS
9
8
10
8
Carefully lift the rear end of the tank, note
the grounding wire on the left side and make
sure not to squeeze or stretch any cables.
Disconnect the grounding wire and the electric
cable to get access to the screws for the left
side cover.
9
Remove the left side cover, see gure.
10
Separate the left side cover into 2 parts. Install
the rear part.
11
Connect the grounding wire and the electric
cable, install the cover, bracket and the seat.
Caution!✋
Make sure that you tighten all screws to the
correct torque and that nothing fouls or restricts
movement of the shock absorber/front fork/
steering damper when the suspension is fully
compressed or extended.

Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone [phone]
fax [phone]
© Öhlins Racing AB. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
SETUP DATA
Warning!⚠
Before you ride/drive, always make sure that the
setup is according to the recommended setup
data. Read about adjustments and setting up
in the Öhlins Owner’s Manual before you make
any adjustments. Contact an Öhlins dealer if
you have any questions about setting up.
ADJUSTMENTS
Part no. MI_DU569_0
Issued 2020-03-11
Length 317 +4/-8 mm
Stroke 65 mm
Rebound 19 clicks
Compression 16 clicks
Spring preload 17 mm
Spring 01092-24
Spring rate 80 N/mm
Free spring length 170 mm
Recommended sag and ride height
R1-R3 29 mm
F1-F3 40 mm
Spring
preload
adjuster
Length
adjuster
Rebound
damping
adjuster
Compression
damping
adjuster