Ohlins KA 216 User manual

Öhlins shock absorber 36 E
Your Öhlins shock absorber type 36 E features
the following adjusters:
Spring preload adjuster
Adjustments are made by turning the rings on
the shock absorber body. Clockwise for harder
adjustment, counter clockwise too release the
preload.
NOTE!
When delivered the Öhlins shock absorber is
dialed to recommended settings for the specific
brand and make of the motorcycle. If you have
changed the setting check like this:
The adjusters have a normal right hand thread. Turn
the damping adjusters clockwise to fully closed (pos.
zero [0]). Turn counter clockwise to open and count
the clicks until you reach the recommended number
of clicks. See Setup data at last page.
CAUTION!
Do not use to much force, delicate sealing surfaces
can be damaged.
Spring
preload
adjuster
Owners Manual
Mounting instruction Öhlins shock absorber
KA 216 for Kawasaki Street Line
© Öhlins Racing AB. All rights reserved. Any reprinting or unauthorized use without the
written permission of Öhlins Racing AB is prohibited. Printed in Sweden.
Bike on a stand. Bike on the ground. Bike with rider on.
Checking sag and ride height
Front suspension
F1. Bike on a stand with the
suspension fully extended = ............
F2. Bike on the ground without rider = ............
F3. Bike on the ground with rider = ............
Free sag F1 - F2 = ............
Ride height F2 - F3 = ............
Rear suspension
R1.Bike on a stand with the
suspension fully extended = ............
R2.Bike on the ground without rider = ........... .
R3.Bike on the ground with rider = ............
Free sag R1 - R2 = ............
Ride height R2 - R3 = ............
NOTE!
If ride height is higher than recommended,
softer spring/springs must be used.
If ride height is lower than recommended,
harder spring/springs must be used.
Contact your Öhlins dealer for advice.
Setup data
Total length 347 mm
Stroke 92 mm
Preload spring 19 mm
F1
R1
F2
R2
F3
R3
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone [phone]. Fax [phone]
www.ohlins.com
KA 216. Issued 02 08 12

Before installation
Öhlins Racing AB can not be held responsible for
any damage whatsoever to suspension compo-
nents or vehicle, or injury to persons, if the in-
structions for fitting and maintenance are not
followed exactly.
Similarly, the warranty will become null and void
if the instructions are not adhered to.
WARNING!
1. Installing a shock absorber, that is not
approved by the vehicle manufacturer, may
affect the stability of your vehicle. Öhlins
Racing AB cannot be held responsible for
any personal injury or damage whatsoever
that may occur after fitting the suspension
components. Contact an Öhlins dealer or
other qualified person for advice.
2. Please study and make certain that you
fully understand all the mounting instructions
and the owners manuals before handling this
shock absorber kit. If you have any questions
regarding proper installation procedures,
contact an Öhlins dealer or other qualified
person.
3. The vehicle service manual must be
referred to when installing the Öhlins
suspension components
Safety signals
Important information concerning safety is
distinguished in this manual by the
following notations:
The Safety alert symbol means:
Caution! Your safety is involved.
WARNING!
Failure to follow warning instructions
could result in severe or fatal injury
to anyone working with, inspecting or
using the suspension, or to bystanders.
CAUTION!
Caution indicates that special pre-
cautions must be taken to avoid dam-
age to the suspension.
NOTE!
This indicates information that is of
importance with regard to procedures.
Öhlins products are subject to continual improve-
ment and development. Consequently, although
these instructions include the most up-to-date
information available at the time of printing, there
may be minor differences between your
suspension and this manual. Please consult your
Öhlins dealer if you have any questions with
regard to the contents of the manual.
NOTE!
During storage and transportation, especially
at high ambient temperature, the oil and
grease used for assembling may run out
inside the packing and damage the expanded
polystyrene packing material. This is not
unusual and is in no way detrimental to the
suspension components.
Kit contents
Before installing the suspension components,
please check the contents of the kit, listed on
the front page of this instruction. If anything is
missing, contact your Öhlins dealer.
Description Part No. Pcs.
Shock absorber Type 36E KA216 2
C-spanner 0710-01 2
Washer 3118-03 2
Sticker Öhlins 0192-01 2
Owners manual 1
WARNING!
1. It´s advisable to have an Öhlins dealer or other
qualified person to fit your shock absorber.
2. Instructions in the vehicle service manual are
to be followed when changing the shock
absorber.
3. When working on a lifted vehicle it must be
securely supported to prevent it from falling.
Mounting instructions
1
Put the motorcycle on a stand so the rear wheel
is clear of the ground. Make sure it's steadily po-
sitioned and will not fall over.
2
Loosen and remove the standard shock
absorber(s). See the motorcycle's Workshop
Manual.
3
Fit the Öhlins shock absorber(s) in the same po-
sition as the standard shock absorber.
NOTE!
Make sure that all bolts are tightened to the cor-
rect torque and that nothing fouls or restricts the
movement of the shock absorber when the sus-
pension is being fully compressed or extended.
WARNING!
Certain modifications may be necessary when
installing the Öhlins shock absorber/suspension.
It is essential that the Mounting instructions are
carefully followed.
4
Continue your work according to the Owners
Manual, section Adjustments.