Ohlins KA 464 User manual

Shock absorber for Kawasaki H2 SX
KA 464
Mounting Instructions
Note!1
Please note that there can be small differences
between your product and the images in
these instructions.
Note!1
Please note that during storage and transport,
especially at high ambient temperature, some
of the oil and grease used for assembly may
leak and stain the packaging. This will not cause
damage to the product, wipe off the excessive
oil or grease with a cloth.
Note!1
Before you install this product, check the kit
contents. If anything is missing, please contact
an Öhlins dealer.
Warning!⚠
Before you install this product, read the Öhlins
Owner’s manual. This product is an important
part of the vehicle and the vehicle stability.
Kit Contents
Description Part No Pcs
Shock absorber KA 464 1
Tie rap 00231-01 2
Screw M8x45 01046-49 1
Screw M6x12 05404-01 2
Sticker Öhlins 10207-01 1
Sticker Memo notes 01180-01 1
Owner´s manual 07242-07 1

2
1
Put the bike on a stand so that the rear wheel
is off the ground.
2
Loosen the original preload adjuster.
3
Loosen the pull rods at the triangle link.
Note!1
You may need to loosen the exhaust clamp to
get the pull rod screw out.
4
Loosen the lower end of the shock absorber.
5
Loosen the upper end of the shock absorber
and remove it downwards.
Note!1
You may need to press the plastic cover above
the screw upwards slightly to get the screw out.
6
Mount the Öhlins unit in the opposite way.
Lower the vehicle so that the suspension
is slightly compressed and then tighten the
screws.
MOUNTING INSTRUCTIONS
Warning!⚠
We strongly recommend to let an Öhlins dealer
install this product.
Warning!⚠
If you work with a lifted vehicle, make sure that it
is safely supported to prevent it from tipping over.
Note!1
When you work with this product, see the
vehicle service manual for vehicle specic
procedures and important data.
Note!1
Before you install this product clean the vehicle.
3

3
MOUNTING INSTRUCTIONS
7
Mount the Öhlins preload adjuster at the
silencer bracket. Use supplied screw M8x45.
8
Tie the hose using supplied ty-raps.
9
Fasten the brake uid reservoir using supplied
screws M6x12.
7

Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone [phone]
fax [phone]
© Öhlins Racing AB. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
SETUP DATA
Warning!⚠
Before you ride/drive, always make sure that the
setup is according to the recommended setup
data. Read about adjustments and setting up
in the Öhlins Owner’s Manual before you make
any adjustments. Contact an Öhlins dealer if you
have any questions about setting up.
ADJUSTMENTS
Part no. MI_KA464_0
Issued 2018-08-13
Length 318 +6/0 mm
Stroke 57 mm
Rebound 14 clicks
Compression 14 clicks
Spring preload 12 mm
Spring 21040-44
Spring rate 120 N/mm
Spring free length 160 mm
Recommended free sag and ride height
R1-R3 50 mm
F1-F3 48 mm
Spring
preload
adjuster
Compression
damping
adjuster
Rebound
damping
adjuster
Length
adjuster